• 전기학회논문지
• /
• 제66권4호
• /
• pp.643-650
• /
• 2017

This pap4er analyzes resonance characteristics of a slave motor that is not controlled by load and parameter differences between Dual motors during parallel operation in middle-low speed. Dual SPMSMs(Surface mounted Permanent Magnet Synchronous Motor) connected in parallel to a single inverter controlled by the master and slave control in this paper. Based on the stability analysis of the SPMSM for a variation of torque angle, the 6th nonlinear state equation of the torque angle variation in the SIMM(Single Inverter Multi Motor) structure is derived according to a mathematical model for the dual motors. In general, an analysis of the 6th order nonlinear state equation is complex. Therefore, a resonance frequency generated from the slave motor is found from the characteristic equation of the 2nd order system obtained by linearization and model reduction near steady state operation point. Through simulations and experiments, it is confirmed that the stability analysis of the SPMSMs and state equation models are useful for the variation of the torque angle analyzed in this paper.

• 한국소음진동공학회논문집
• /
• 제20권9호
• /
• pp.849-855
• /
• 2010

Damping may change the response characteristics of nonlinear oscillations due to the parametric excitation of a thin cantilever beam. When the natural frequencies of the first bending and torsional modes are of the same order of magnitude, we can observe the one-to-one combination resonance in the perturbation analysis depending on the characteristic parameters. The nonlinear behavior about the combination resonance reveals a chaotic motion depending on the natural frequencies and damping ratio. We can analyze the chaotic dynamics by using the eigenvalue analysis of the perturbed components. In this paper, we derived the equations for autonomous system and solved them to obtain the characteristic equation. The stability analysis was carried out by examining the eigenvalues. Numerical integration gave the physical behavior of each mode for given parameters.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제11B권3호
• /
• pp.98-103
• /
• 2001

This paper presents the numerical analysis of piezoelectric devices using three-dimensional finite element analysis. The characteristic of piezoelectric transducer, such as mechanical displacement and electrical are analyzed and the validity is confirmed by experiments Applying the finite element routine to a piezoelectric transformer, the resonance features electrical impedance. the ratio of step-up voltage and vibration mode of piezoelectric transformer are calculated numerically By using three-dimensional finite element method effects of width variation to resonance features, electrical input impedance and the voltage step-up ratio for a piezoelectric transformer, can be considered in design procedure.

• Journal of Power Electronics
• /
• 제18권3호
• /
• pp.746-756
• /
• 2018

Harmonic resonance exists in grid-connected inverter systems. In order to determine the network components that contribute to harmonic resonance and the composition of the resonant circuit, sensitivity theory is applied to the resonance characteristic analysis. Based on the modal analysis, the theory of sensitivity is applied to derive a formula for determining the sensitivities of each network component parameter under a resonance circumstance that reflects the participation of the network component. The solving formula is derived for both parallel harmonic resonance and series harmonic resonance. This formula is adopted to a 4-node grid-connected test system. The analysis results reveal that for a certain frequency, the participation of parallel resonance and series resonance are not the same. Finally, experimental results demonstrate that the solving formula for sensitivity is feasible for grid-connected systems.

• 한국기계가공학회지
• /
• 제21권7호
• /
• pp.21-27
• /
• 2022

This study was conducted to evaluate the structural stability of a CNC automatic lathe structure and avoid resonance. The analysis conditions were analyzed by applying the weight of the upper assembly. From the structural analysis, the stress and deformation were low, and the safety factor was high. From the dynamic characteristic analysis, it was determined that resonance does not occur because the natural frequency is outside the driving range. The error between the dynamic characteristic analysis and vibration test results is very low; thus, the reliability of the analysis results can be secured.

• Journal of Magnetics
• /
• 제18권3호
• /
• pp.250-254
• /
• 2013

In this research, the linear electrical generator in wave energy farm utilizing resonance power buoy system is studied. The mechanical resonance characteristics of the buoy and the wave are analyzed to maximize the kinetic energy in a relatively small wave energy area where WRPS is operated. In this research, we chose an analog model of the linear electrical generator of which size is one-hundredth of an actual size of it in WPRS (Wave energy farm utilizing Resonance Power buoy System) prior to verifying the characteristics of actual model of linear electrical generator in WRPS. In addition, the finite element analysis is conducted using commercial electromagnetic analysis software named MAXWELL to examine the electric characteristic of linear generator. Finally, for the verification of dynamic and electric characteristics of linear generator, the prototype was manufactured and the experiments to measure the displacement and the output electric power were performed.

• 한국전기전자재료학회논문지
• /
• 제22권2호
• /
• pp.142-150
• /
• 2009

We constructed a Class I flextensional transducer, and analyzed the variation of the resonance frequency of the transducer in relation to its structural and material variables. We used the FEM for the analysis. Total length of the transducer, thickness and material properties of the shell have large effects on the resonance frequency. While outer radius of the ceramic stack and material properties of the ceramic stack have no effect on the resonance frequency. In addition, the validation of the FE model was verified by manufacturing and comparison of the impedance analysis. Results of the present work can be utilized to design a Class I flextensional transducers of various resonance frequency.

• 비파괴검사학회지
• /
• 제31권2호
• /
• pp.174-180
• /
• 2011

본 연구에서는 초음파원자현미경을 이용하여 비파괴적인 표면탄성이미지 분석과 나노표면에서의 기계적 물성 평가를 연구하였다. 이를 위해 접촉역학 특성에 따른 캔틸레버의 공진주파수 변화를 이론적으로 해석하고 실험적으로 측정하였다. 스프링-질량 모델과 Herzian 이론을 이용하여 계산한 이론적인 접촉공천주파수는 초음파원자현미경 캔틸레버의 실험적인 접촉 공진주파수의 변화와 매우 유사하였다. 결과적으로, 초음파원자현미경의 표면 높이 이미지와 진폭이미지를 성공적으로 얻을 수 있었고 진폭신호를 통하여 시료표면에서의 탄성특성을 정성적으로 평가하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 F
• /
• pp.2033-2035
• /
• 1998

This paper describes a DC-DC converter connected two unites inverters, a half-bridge type of high frequency resonance inverter, at the input with parallel. The proposed paper certified that theorem waveforms are equal to experiment waveforms, in addition, it estimated characteristics such as characteristic of average power, characteristic of average output voltage, characterisic of output voltage ripple etc., for designing the device with normalized parameter value.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권5호
• /
• pp.309-317
• /
• 2004

This paper suggested the vibration characteristic improvement by variation mode of ring type ultrasonic motor. Design for the piezoelectric ceramic and elastic body of stator were calculated by the finite element method(FEM) that consider the resonance frequency, vibration mode and coupling efficiency etc. Through the result of vibration analysis from 6 order mode to 8 mode, the 7 order mode was gained very an excellent results that it was the coupling efficient, minimum power loss and bending vibration value. Here over 7 order mode, this paper was acquired that an output current for input voltage was very a large increased results. The result of vibration calculation, from thickness 0.5[mm] to 2[mm], knew the fact that the vibration displacement at 0.5[mm] is an high value too. From such result, this paper was manufactured the ultrasonic motor of outer diameter 5O[mm] , inter 22[mm] having the about 43.86[KHz] resonance frequency. We have gated that a simulation result is 42.2[KHz] and an experiment result is 43.86[KHzl The propriety of this paper was established though comparison. investigation of simulation and experiment result.