• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.263-266
• /
• 1999

In this work, a A/D converter is implemented to obtain 8bit resolution at a conversion rate of 10MS/s for video applications. This architecture is proposed using the Pipelined architecture for high speed conversion rate and the Successive - Approximation architecture for low power consumption, and consists of two identical stages that consist of sample/hold circuit, low power comparator, voltage reference circuit and MDAC of binary weighted capacitor array. Proposed A/D converter is designed using 0.25${\mu}{\textrm}{m}$ CMOS technology The SNR is 80㏈ at a sampling rate of 10MHz with 1.95MHz sine input signal. When an 8bit 10MS/s A/D converter is simulated, the Differential Nonlinearity / Integral Nonlinearity (DNL/ INL) error are $\pm$0.5 / $\pm$2 LSB, respectively. The power consumption is 13㎽ at 10MS/s.

• Journal of Environmental Science International
• /
• v.18 no.10
• /
• pp.1071-1077
• /
• 2009

A novel pretreatment technique was applied to the conventional Pt/alumina catalyst to prepare for the highly efficient catalyst for the preferential oxidation of carbon monoxide in hydrogen-rich condition. Their performance was investigated by selective CO oxidation reaction. CO conversion with the oxygen-treated Pt/Alumina catalyst increased remarkably especially at the low temperature below $100^{\circ}C$. This result is promising for the normal operation of the proton exchange membrane fuel cell (PEMFC) without CO poisoning of the anode catalyst. XRD analysis results showed that metallic Pt peaks were not observed for the oxygen-treated catalyst. This implies that well dispersed small Pt particles exist on the catalyst. This result was continued by high resolution transmission electron microscopy (HRTEM) analysis. Consequently, it can be concluded that highly dispersed Pt nanoparticles could be prepared by the novel pretreatment technique and thus, CO conversion could be increased considerably especially at the low temperatures below $100^{\circ}C$.

• Proceedings of the KIEE Conference
• /
• 1988.07a
• /
• pp.571-573
• /
• 1988

A new ripple analog-to-digital converter(ADC) has been developed. It consists of two parallel ADCs and a switching network. The circuit operates on the input signal in two serial steps. First a coarse conversion is made to determine the most significant bits by the first parallel ADC. The results control a switching network to connect the series resistor segment, the analog signal is contained within, to the second parallel ADC. At second step, a fine conversion is made to determine the least signification bits by the second parallel ADC. The circuit requires 2(2$\frac{N}{2}$) comparators, 2(2$\frac{N}{2}$) resistors, and 2(2$\frac{N}{2}$) switches for N-bit resolution.

• Current Optics and Photonics
• /
• v.1 no.2
• /
• pp.150-156
• /
• 2017

A diffraction limited optical system for head mounted displays (HMDs) was designed. This optical system consists of four modules, including 1:5 mm and 5:30 mm beam expanders, polarization grating-polarization conversion system (PG-PCS) and refractive/diffractive projection optical module. The PG-PCS module transforms the unpolarized Gaussian beam to a linearly polarized beam and it simultaneously homogenizes the spatial intensity profile. The optical projector module has a $30^{\circ}$ field of view, a 22 mm eye relief, and a 10 mm exit pupil diameter with a compact structure. Common acrylic materials were utilized in the optical design process; therefore, the final optical system was lightweight. The whole optical system is suitable for a 0.7 inch liquid crystal on silicon microdisplay (LCOS) with HDTV resolution ($1920{\times}1080$) and $8.0{\mu}m$ pixel pitch.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.4 no.1
• /
• pp.33-36
• /
• 2009

Incremental converters provide a solution for such measurement applications, as they retain most of the advantages of conventional ${\Delta}{\Sigma}$ converters, and yet they are capable of offset-free and accurate conversion. Most of the previous research on incremental converters was for single-channel and dc signal applications, where they can perform extremely accurate data conversion with more than 20-bit resolution. In this paper, a design technique for implementing multi-channel incremental data converters to convert narrow bandwidth ac signals is discussed. It incorporates the operation principle, topology, and digital decimation filter design. The theoretical results are verified by simulation results.

• Proceedings of the Korean Society of Computer Information Conference
• /
• 2015.07a
• /
• pp.268-271
• /
• 2015

본 논문에서는 고해상도 비디오를 위한 프레임 레이트 변환 방법을 제시한다. 서로 다른 방식이나 포맷을 가진 영상 신호를 변환할 때에는 시각적으로 거슬리는 움직임 지터(motion jitter)나 영상의 모서리에서의 블러링(blurring) 현상이 일어날 수 있다. 제시하는 방법에서는 이러한 문제점을 해결하기 위해 양방향 움직임 추정/보상을 이용하여 프레임 레이트를 증가 변환한다. 또한 보다 정확한 움직임 벡터를 찾기 위해 다중 프레임을 통한 양방향 탐색 방법을 제안한다. 먼저, 픽셀 값을 알고 있는 현재 프레임과 이전 프레임간의 움직임 벡터를 이용하여 양방향 움직임 벡터를 얻는다. 얻은 움직임 벡터는 벡터 스무딩 블록을 거친다. 그 후 OBMC(Overlapped Block Motion Compensation)를 이용하여 보간 프레임을 구성한다. 실험 결과는 기존 방법들보다 제안 방법이 주관적 화질 면에서 우수함을 나타낸다.

• Proceedings of the KIEE Conference
• /
• 1993.07a
• /
• pp.450-452
• /
• 1993

In this study, a method is suggested to design the A/D conversion system which has high resolution to convert load cell signal. First, hardware was designed to reduce the offset voltage of integrator and comparator. And then, a calibration software technique was performed to obtain the stable data from A/D converter. The optimal parameters of each elements in the circuits was selected using the SPICE simulation. The main advantage of our method is high precision A/D converter can be constructed with low cost and high confidence. Therefore proposed method is expected to be used in the industrial field where a high precision measurement is required.

• Korean Journal of Optics and Photonics
• /
• v.14 no.6
• /
• pp.573-577
• /
• 2003

We report an effect of photon pairs on single-photon detection rates, while Hong-Ou-Handel's two-photon interference experiment is performed with photons produced in noncollinear type-I parametric down-conversion. Photon pairing behavior or spatial bunching is measured and shown to cause a decrease in the single photon counting rate. Such a dip is found to result from the fact that the single-photon timing resolution of photodetectors is much longer compared to the time interval between the two photons incident on the single-photon detector.

• KSBB Journal
• /
• v.23 no.3
• /
• pp.257-262
• /
• 2008

In this study, the reaction conditions for lipase-catalyzed resolution of racemic naproxen 2,2,2-trilfluoroethyl thioester were optimized, and the effect of surfactants was investigated. Among the organic solvents tested, the isooctane showed the highest conversion (92.19%) in a hydrolytic reaction of (S)-naproxen 2,2,2-trifluoroethyl thioester. In addition, the isooctane induced the highest initial reaction rate of (S)-naproxen 2,2,2-trifluoroethyl thioester ($V_s=2.34{\times}10^{-2}mM/h$), the highest enantioselectivity (E = 36.12) and the highest specific activity ($V_s/(E_t)=7.80{\times}10^{-4}mmol/h{\cdot}g$) of lipase. Furthermore, reaction conditions such as temperature, concentration of the substrate and enzyme, and agitation speed were optimized using response surface methodology (RSM), and the statistical analysis indicated that the optimal conditions were $48.2^{\circ}C$, 3.51 mM, 30.11 mg/mL and 180 rpm, respectively. When the optimal reaction conditions were used, the conversion of (S)-naproxen 2,2,2-trifluoroethyl thioester was 96.5%, which is similar to the conversion (94.6%) that was predicted by the model. After optimization of reaction conditions, the initial reaction rate, lipase specific activity and conversion of (S)-naproxen 2,2,2-trifluoroethyl thioester increased by approximately 19.54%, 19.12% and 4.05%, respectively. The effect of surfactants such as Triton X-100 and NP-10 was also studied and NP-10 showed the highest conversion (89.43%), final reaction rate of (S)-naproxen 2,2,2-trifluoroethyl thioester ($V_s=1.175{\times}10^{-2}mM/h$) and enantioselectivity (E = 59.24) of lipase.

• Journal of Environmental Science International
• /
• v.29 no.1
• /
• pp.95-108
• /
• 2020

Silver nanoparticles were loaded onto g-C₃N₄ (CN) with a nanoroll-type morphology (Ag/CN) synthesized using a co-polymerization method for highly selective conversion of toxic nitrobenzene to industrially-valuable aminobenzene. Scanning electron microscopy and high-resolution transmission electron microscopy (HRTEM) images of Ag/CN revealed the generation of the nanoroll-type morphology of CN. Additionally, HRTEM analysis provided direct evidence of the generation of a Schottky barrier between Ag and CN in the Ag/CN nanohybrid. Photoluminescence analysis and photocurrent measurements suggested that the introduction of Ag into CN could minimize charge recombination rates, enhancing the mobility of electrons and holes to the surface of the photocatalyst. Compared to pristine CN, Ag/CN displayed much higher ability in the photocatalytic reduction of nitrobenzene to aminobenzene, underscoring the importance of Ag deposition on CN. The enhanced photocatalytic performance and photocurrent generation were primarily ascribed to the Schottky junction formed at the Ag/CN interface, greater visible-light absorption efficiency, and improved charge separation associated with the nanoroll morphology of CN. Ag would act as an electron sink/trapping center, enhancing the charge separation, and also serve as a good co-catalyst. Overall, the synergistic effects of these features of Ag/CN improved the photocatalytic conversion of nitrobenzene to aminobenzene.