• Fire Science and Engineering
• /
• v.24 no.5
• /
• pp.136-141
• /
• 2010

The purpose of this study is to examine the structure and heat generation mechanism of low voltage switches used to turn on or off the power supply to an indoor lighting system and investigate how the fixtures and movable contacts of the switches are damaged depending on the types of energy sources in order to secure the judgment base for expected PL disputes. Based on the Korean Standard (KS) testing method for incombustibility, this study applied a general flame to the switch. In addition, current was supplied to the switch using the PCITS (Primary Current Injection Test System). The ambient temperature and humidity were maintained at $22{\pm}2^{\circ}C$ and 40~60% respectively while performing the test. It is thought that the switch generated heat due to a defective connection of the wire and clip, insulation deterioration and defective contact of the movable contact, etc. The surface of the switch damaged by the general flame was uniformly carbonized. When the flame source was removed, the fire on the switch was extinguished naturally. From the result obtained by disassembling the switch carbonized by the general flame, it could be seen that fixtures and movable contacts remained in comparatively good shape but the enclosure, clip support, movable contact, indicating lamp, etc. showed carbonization and discoloration. In the case of the switch damaged by overcurrent, the clip connecting the wires, clip support, etc. showed almost no trace of damage, but the fixtures, movable contact, indicating lamp, etc. were severely carbonized. That is, the sections with high contact resistance were intensively damaged and showed a damage pattern indicating that carbonization progressed from the inside to the outside. Therefore, it is possible to judge the initial energy source by analyzing the characteristics of the carbonization pattern and the metal fixtures of damaged switches.

• Journal of the Korea Concrete Institute
• /
• v.15 no.2
• /
• pp.288-296
• /
• 2003

Generally, application of steel pipe pile as deep foundation member needs special requirement for the connection method between steel pipe pile and concrete footing. Even though two types of connection method are suggested in the related specification, type B-method is provident. To investigate real structural behavior of type B connection, several load tests are done with carefully designed experimental system. The purpose of this experiment is mainly focused on the understanding of actual behavior which can be predicted by design theory. At this research stage, vertical and lateral loading test are done for three types of specimen to review stress concentration, formation and behavior of imaginary RC column in the footing and effect of non-slip device installed in the steel pipe pile. The load resistance mechanism in these specific connection method is predicted based on both experimental results. The three-dimensional finite element modeling is also done for the purpose of comparison between numerical and experimental result. With all the results gained from experiment the structural behavior of imaginary RC column in the design concept is confirmed. The role of non-slip device is very important and it affects the resistance capacity with help of composite action of concrete and steel pipe pile.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.1
• /
• pp.512-520
• /
• 2020

Recently, the applications of the standing column well (SCW) ground heat exchanger (GHX) have increased significantly in Korea as a heat transfer mechanism of ground source heat pump systems (GSHP) because of its high heat capacity and efficiency. Among the various design and operating parameters, bleeding was found to be the most important parameter for improving the thermal performance, such as ground thermal conductivity and borehole thermal resistance. In this study, a bleeding analysis model was developed using the thermal response test data, and the effects of bleeding rates and bleeding locations on the thermal performance of anSCW were investigated. The results show that, when the ground water flows into the top of anSCW, the time variation of circulating water temperature decreased with increasing bleeding rate, and the ground thermal conductivity increases by as much as 179% with a 30% bleeding rate. When the ground water flows into the bottom of the SCW, the circulating water temperatures become almost constant after the increase in the beginning time because the circulating water exchanges heat with the ground structure before mixing with the ground water at the bottom.

• The Journal of the Korea Contents Association
• /
• v.15 no.12
• /
• pp.61-72
• /
• 2015

The capitalistic resistance movement attempted in most modern art areas was carried out through a complete convergence of the art and skill, which was the new formation of the symbolic boundary. Although this resistance movement was aimed at restoring artisan art through the revival of tbe work of handicraftsmen, it consequently caused the stratification of the art and became a de-artisan art excluding the autonomous labor. Hereupon, this study would focus on Bauhaus which attempted to dismantle the symbolic boundary through the convergence of the technology and art which actively used the condition the great industry brought only as an effort for the restoration of artisan labor, and would examine the actor-network of Bauhaus. Therefore, this study would examine the Bauhaus' artistic trend, the 16C Renaissance art promotion movement, and the 19C art crafts movement in the network-oriented relation, and would analyze the Bauhaus' ideological source which expressed design democracy through the bridging role of and analyze the artisan art and the mechanism that had the new technology fused. Furthermore, the convergence possibility of the 'collaboration spirit' being embodied as a philosophy of the democracy in the design continues with the tremendous influence of the new technology.

• Tribology and Lubricants
• /
• v.11 no.5
• /
• pp.128-135
• /
• 1995

Atomic force microscopy/friction force microscopy (AFM/FFM) techniques are increasingly used for tribological studies of engineering surfaces at scales, ranging from atomic and molecular to microscales. These techniques have been used to study surface roughness, adhesion, friction, scratching/wear, indentation, detection of material transfer, and boundary lubrication and for nanofabrication/nanomachining purposes. Micro/nanotribological studies of single-crystal silicon, natural diamond, magnetic media (magnetic tapes and disks) and magnetic heads have been conducted. Commonly measured roughness parameters are found to be scale dependent, requiring the need of scale-independent fractal parameters to characterize surface roughness. Measurements of atomic-scale friction of a freshly-cleaved highly-oriented pyrolytic graphite exhibited the same periodicity as that of corresponding topography. However, the peaks in friction and those in corresponding topography were displaced relative to each other. Variations in atomic-scale friction and the observed displacement has been explained by the variations in interatomic forces in the normal and lateral directions. Local variation in microscale friction is found to correspond to the local slope suggesting that a ratchet mechanism is responsible for this variation. Directionality in the friction is observed on both micro- and macro scales which results from the surface preparation and anisotropy in surface roughness. Microscale friction is generally found to be smaller than the macrofriction as there is less ploughing contribution in microscale measurements. Microscale friction is load dependent and friction values increase with an increase in the normal load approaching to the macrofriction at contact stresses higher than the hardness of the softer material. Wear rate for single-crystal silicon is approximately constant for various loads and test durations. However, for magnetic disks with a multilayered thin-film structure, the wear of the diamond like carbon overcoat is catastrophic. Breakdown of thin films can be detected with AFM. Evolution of the wear has also been studied using AFM. Wear is found to be initiated at nono scratches. AFM has been modified to obtain load-displacement curves and for nanoindentation hardness measurements with depth of indentation as low as 1 mm. Scratching and indentation on nanoscales are the powerful ways to screen for adhesion and resistance to deformation of ultrathin fdms. Detection of material transfer on a nanoscale is possible with AFM. Boundary lubrication studies and measurement of lubricant-film thichness with a lateral resolution on a nanoscale have been conducted using AFM. Self-assembled monolyers and chemically-bonded lubricant films with a mobile fraction are superior in wear resistance. Finally, AFM has also shown to be useful for nanofabrication/nanomachining. Friction and wear on micro-and nanoscales have been found to be generally smaller compared to that at macroscales. Therefore, micro/nanotribological studies may help def'me the regimes for ultra-low friction and near zero wear.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.82-82
• /
• 2009

Although leakage at a low carbon steel pipe made by electrical resistance welding(ERW) was reported due to grooving corrosion, the cause for the corrosion has not yet been cleared. So lots of researches were carried out already about grooving corrosion mechanism of ERW carbon steel pipe but there is seldom study for water hammer happened by fluid phenomenon and corrosion rate by flow velocity. In this study, the corrosion test carried out using the ERW carbon steel pipe by changed the water speed and heat input in a month. The level of dissolved oxygen is maintained 5~5.5mg/l(amount of dissolved oxygen in tap water). The water speed for corrosion test is 1m/s, 2m/s, 3m/s. As the results, grooving corrosion rate is increased cause by water speed in the pipe. In the case of the ERW pipe with more heat input, grooving corrosion rate is decreased. It is therefore that welding heat input should be controlled based on the carbon content of the pipe in order to improve the corrosion reistance of the ERW pipe.

• Korean Journal of Plant Tissue Culture
• /
• v.24 no.6
• /
• pp.361-367
• /
• 1997

This study was carried out to select cadmium resistant cell lines from leaf-derived calli of diploid and haploid of Nicotiana tabacum cv. BY4, for understanding adaptation mechanism of plants in cadmium contaminated environment. suspended cell clumps were plated onto selection medium containing 0 to 2,000 $\mu$M cadmium. Cadmium resistant colonies were formed on the selection medium after 3 or 4 weeks of culture. The minimum inhibition concentration (MIC) of cadmium on colony formation were 300 $\mu$M in diploid and 200 $\mu$M in haploid plants, respectively. In order to test the resistance to cadmium, selected cell line on MIC were transferred to medium containing high concentration of cadmium. The selected cell lines, especially haploid cell line, were resistant an the high concentration of cadmium. And dry weight, ash weight, and cadmium contents of cell were increased. These results indicated that the selected cell lines showed higher resistance of cadmium than control cells, and haploid plant is more resistant than diploid plant on medium with cadmium.

• The Journal of Society for e-Business Studies
• /
• v.22 no.2
• /
• pp.169-185
• /
• 2017

Juliano Rizzo and Thai Duong, the authors of the BEAST attack [11, 12] on SSL, have proposed a new attack named CRIME [13] which is Compression Ratio Info-leak Made Easy. The CRIME exploits how data compression and encryption interact to discover secret information about the underlying encrypted data. Repeating this method allows an attacker to eventually decrypt the data and recover HTTP session cookies. This security weakness targets in SPDY and SSL/TLS compression. The attack becomes effective because the attacker is enable to choose different input data and observe the length of the encrypted data that comes out. Since Transport Layer Security (TLS) ensures integrity of data transmitted between two parties (server and client) and provides strong authentication for both parties, in the last few years, it has a wide range of attacks on SSL/TLS which have exploited various features in the TLS mechanism. In this paper, we will discuss about the CRIME and other versions of SSL/TLS attacks along with countermeasures, implementations. We also present direction for SSL/TLS attacks resistance in practice.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.3
• /
• pp.1191-1196
• /
• 2013

Among Gram-negative pathogens in Korea, the incidence of resistance to third generation cephalosporins is becoming an ever-increasing problem. The production of extended-spectrum ${\beta}$-lactamase (ESBL) is the main mechanism of bacterial resistance to a third-generation cephalosporins and monobactams. Accurate identification of the ESBL genes are necessary for surveillance and epidemiological studies of the mode of transmission in the hospital. This study was conducted to detect the genes encoding ESBL of 46 K. penumoniae isolated from Daejeon, Chungnam and Chungbuk regional university hospitals from February to August in 2012. The phenotypes of the isolated specimens were examined according to the combination disc test (CDT) by the Clinical and Laboratory Standards Institute (CLSI). Forty two ESBL producing K. penumoniae isolates could be detected using ceftazidime (CAZ) discs with and without clavulanate (CLA). By CDT, 42 K. pneumoniae strains were confirmed to be ESBL strains. Genotyping was performed by multiplex PCR with type-specific primers. By PCR analysis, TEM gene in 46 strains, SHV gene in 37 strains and CTX-M genes in 14 strains were identified. Ten isolates did carry genes encoding ESBLs of all types TEM, SHV and CTX-M. The multiplex polymerase chain reaction (PCR) analysis was better to detect and differentiate ESBL producing K. penumoniae strains in clinical isolates.

• Polymer(Korea)
• /
• v.33 no.1
• /
• pp.39-44
• /
• 2009

Polymer substrates were fabricated by using poly (phenylene ether) as a base resin, N,N'-m-phenylenedimaleimide (PDMI) as a crosslinking agent and decabromodiphenylethane as a flame retardant. The effects of crosslinking agent and flame retardant on physical properties such as dielectric property of the substrate were investigated. Thermal curing feature of PDMI with or without an initiator was analyzed by DSC, and then, PPE-PDMI test compositions were designed based on this result. Composite sheets were cast by film coater, laminated under vacuum and pressure, and then, the changes of dielectric constant, dielectric loss, peel strength, solder heat resistance and inflammability according to increasing amount of PDMI and flame retardant were evaluated, Dielectric constant and dielectric loss showed increasing trend with increasing amount of PDMI and flame retardant, but solder heat resistance and inflammability were improved. Peel strength was obtained higher than 1 kN/m when PDMI above 10 wt% was added, but slightly decreased as the amount of flame retardant increased. From the measured gel contents, the reaction mechanism of PPE-PDMI system was deduced to the formation of network structure by crosslinking PDMI with PPE rather than the formation of semi-IPN structure. In conclusion, the polymer composite substrate materials with dielectric constant of 2.52$\sim$2.65 and dielectric loss below 0.002 at 1 GHz were obtained and they will be proper for high frequency applications.