• Journal of the Korean Wood Science and Technology
• /
• v.36 no.3
• /
• pp.30-38
• /
• 2008

Petroleum-based resin adhesives have extensively been used for the production of wood panels. However, with the increase of manufacturing cost and the environmental issue, such as the emission of volatile organic compounds, of the adhesive resins, it is necessary to be developed new adhesive systems. In this study, the potential of okara, which is a residue wasted from the production of tofu, for the development of bio-based adhesives was investigated. At first, the physical and chemical properties of okara were examined. After okara was hydrolyzed in acidic and/or alkaline solutions, okara-based adhesive resins were formulated with the mixtures of the okara hydrolyzates and phenol formaldehyde (PF) prepolymer. The adhesive resins were used for the fabrication of plywood panels, and then the adhesive strength and formaldehyde emission of the plywood panels were measured to examine the applicability of the resin adhesives for the production of plywood panels. The solids content and pH of the okara used in this study were around 20% and weak acidic state, respectively. In the analysis of its chemical composition, the content of carbohydrate was the highest, and followed by protein. The shear strengths of plywood fabricated with okara-based resin adhesives exceeded a minimum requirement of KS standard for ordinary plywood, but its wood failure did not reach the minimum requirement. In addition, the formaldehyde emissions of all plywood panels were higher than that of E1 specified in the KS standard. Based on these results, okara has the potential to be used as a raw material of environmentally friendly adhesive resin systems for the production of wood panels, but further researches - biological hydrolysis of okara and various formulations of PF prepolymer - are required to improve the adhesive strength and formaldehyde emission of okara-based resin adhesives.

• Journal of Food Hygiene and Safety
• /
• v.29 no.2
• /
• pp.131-140
• /
• 2014

The objective of this study was to develop a simultaneous method of 8 penicillin antibiotics including amoxicillin, ampicillin, cloxacillin, dicloxacillin, nafcillin, oxacillin, penicillin G and penicillin V in meat using LC-MS/MS. The procedure involves solid phase extraction with HLB cartridge and subsequent analysis by LC-MS/MS. To optimize MS analytical condition of 8 compounds, each parameter was established by multiple reaction monitoring in positive ion mode. The chromatographic separation was achieved on a $C_{18}$ column with a mobile phase of 0.05% formic acid and 0.05% formic acid in acetonitrile at a flow rate of 0.2 mL/min for 20 min with a gradient elution. The developed method was validated for specificity, linearity, accuracy and precision in beef, pork and chicken. The recoveries were 71.0~106%, and relative standard deviations (RSD) were 4.0~11.2%. The limit of detection (LOD) and the limit of quantification (LOQ) were 0.003~0.008 mg/kg and 0.01~0.03 mg/kg, respectively, that are below maximum residue limit (MRL) of the penicillins. This study also performed survey of residual penicillin antibiotics for 193 samples of beef, pork and chicken collected from 9 cities in Korea. Penicillins were not found in all the samples except a sample of pork which contained cloxacillin (concentration of 0.08 mg/kg) below the MRL (0.3 mg/kg).

• Journal of agriculture & life science
• /
• v.46 no.3
• /
• pp.97-108
• /
• 2012

Physical, chemical and biological hazards of strawberry farms at the cultivation stage were analyzed to establish the GAP(Good Agricultural Practice) system. Samples were collected from the plants, cultivation environments(water, soil and air), and personal hygiene (hand, glove, and clothes) of three strawberry farms(A, B, and C) and were tested to analyze physical, chemical (heavy metals and pesticide residues), and biological(sanitary indications and foodborne pathogens) hazards. Physical hazards such as insects and pieces of metal and glass were found in the strawberry farms and can be potential bow for strawberry products. Heavy metal and pesticide residue as chemical hazards were detected at levels lower than the regulation limit. In case of biological hazards, total bacteria and coliform were detected at the levels of 1.6~7.3 and 1.3~5.6 log CFU/g, leaf, mL, hand or $100cm^2$. However, Escherichia coli was not detected in all samples. Bacillus cereus and Staphylococuus aureus were detected at levels of ${\leq}$ 1.1~6.1 log CFU and 4.7~5.4 log CFU/g, mL, hand or $100cm^2$, whereas Listeria monocytogenes, E. coli O157 and Salmonella spp. were not detected in all samples. This study demonstrates that various harzards were in strawberry farms at the growing stage. Therefore proper management such as GAP is needed to prevent the occurrence of food poisoning associated with the hazards revealed in this study.

• Journal of Food Hygiene and Safety
• /
• v.34 no.5
• /
• pp.413-420
• /
• 2019

In this study, a sample preparation method and a simultaneous determination method by ultra-high performance liquid chromatography coupled with tandem mass spectrometry for 9 isomers of chlorogenic acid and arbutin in fruits were developed. The samples were extracted using 90% methanol (pH 3.0), with the solutions being shaken and then sonicated for 10 min each. After centrifugation at 4,000 rpm for 10 min, the extraction was concentrated under a vacuum at $40^{\circ}C$ using a vacuum evaporator. The residue was dissolved in 5 mL of 5% methanol and filtered through a $0.45{\mu}m$ membrane before UHPLC-MS/MS analysis. The separations were performed on a C18 column with gradient elution of water (containing 0.1% formic acid) and methanol (containing 0.1% formic acid). The specificity, linearity, limit of detection, limit of quantification, accuracy, and precision of the proposed methods were also evaluated.

• Korean Journal of Soil Science and Fertilizer
• /
• v.18 no.4
• /
• pp.325-335
• /
• 1985

Biogas production from agricultural wastes were summarized as follows: 1. Biogas Generation Characteristics of Various Manures and Residues a. Gas yield from crop residues like rice straw, rice hull, corn stalk and coconut husk can be improved by addition of animal manures. b. Gas yield from coconut husk can be improved through aerobic fermentation for at least one week before loading in the digester. c. Gas yield from fresh rice straw is better than from pre-fermented one, whether alone or in combination with animal manures. d. Initial study has shown that fresh azolla can be substituted for animal manures in manurerice straw combinations and gas yield derived based on unit volatile solids loaded is actually better than for manure-residue combinations. e. Gas production is highly sensitive to substrate pH and becomes almost nil at a pH of below 6. 2. Effect of ambient conditions and other factors on biogas production in a house hold-size digester. a. Results showed that compaction of rice straw in straw-manure combination can reduce gas yield compared with loosely mixed straw. b. The effective gas production period extended to 70 days using freshly threshed rice straw and fresh cattle manure as feed material. c. Underground and above ground digesters with shade have relatively more stable substrate temperature than aboveground exposed digesters. This relative temperature instability may likely be the reason for lower gas yield for the exposed aboveground digester loaded with loose straw-cattle manure substrate, compared with the underground digester with the same substrate. 3. Economic Analysis a. Based on prevailing costs of fuel, materials, and labor in the Philippines, biogas produced from the household size system is cheaper than either LPG or kerosene. b. If other benefits like organic fertilizer, pollution control and convenience are considered, biogas will surely be the best alternative fuel source.

• Journal of Food Hygiene and Safety
• /
• v.34 no.1
• /
• pp.13-21
• /
• 2019

A method was developed for the simultaneous detection of an antibiotic fungicide, streptomycin, and its metabolite (dihydrostreptomycin) in agricultural products using liquid chromatography-tandem mass spectrometry (LC-MS/MS). The samples were extracted using methanol adjusted to pH 3 using formic acid, and purified with a HLB (Hydrophilic lipophilic balance) cartridge. The matrix-matched calibration curves were constructed using seven concentration levels, from 0.001 to 0.1 mg/kg, and linearity of five agricultural products (hulled rice, potato, soybean, mandarin, green pepper), with coefficients of determination $(R^2){\geq}0.9906$, for streptomycin and dihydrostreptomycin. The mean recoveries at three fortification levels (LOQ, $LOQ{\times}10$, $LOQ{\times}50$, n = 5) were from 72.0~116.5% and from 72.1~116.0%, and relative standard deviations were less than 12.3% and 12.5%, respectively. The limits of quantification (LOQ) were 0.01 mg/kg, which are satisfactory for quantification levels corresponding with the Positive List System. All optimized results satisfied the criteria ranges requested in the Codex guidelines and the Food Safety Evaluation Department guidelines. The present study could serve as a reference for the establishment of maximum residue limits and be used as basic data for detection of streptomycin and dihydrostreptomycin in food.

• Journal of Food Hygiene and Safety
• /
• v.36 no.3
• /
• pp.239-247
• /
• 2021

In order to confirm the impact of the Positive List System (PLS) being applied to all agricultural products from January 1, 2019, we analyzed 28,693 points of inspection-related data on agricultural products distributed in Gyeonggi-do from 2018 to 2020. The ratio of cases exceeding the standard for the total inspection performance was 1.0% in 2018, 1.2% in 2019, and 1.2% in 2020. Out of the 114 cases exceeding the standard in 2019, 55 were applied on a Maximum Residue Limit (MRL) of 0.01 mg/kg, and out of the 115 cases exceeding the standard in 2020, 66 were applied on a MRL of 0.01 mg/kg. To improve this, it seems necessary to manage unintentional pollution, conventional use for unregistered crops, and illegal pesticides. Fluquinconazole detection resulted from unintentional contamination, and diazinon, chlorothalonil, and methabenzthiazuron detection resulted from conventional use in unregistered crops. Chinomethionat is a pesticide component that was discarded in the past and its current use has been attributed to the smuggling of pesticides. This study and future monitoring data can be used as reference data for system supplementation and on-site management reinforcement.

• Journal of Korean Society of Forest Science
• /
• v.110 no.2
• /
• pp.217-232
• /
• 2021

This study calculated the productivity and cost of extraction and processing of logging residues by cut-to-length (CTL) and whole-tree (WT) harvesting methods. In addition, the comparative analysis of the characteristics of wood chip fuel to examine whether it was suitable for the fuel conditions of the energy facility. In the harvesting and processing system to produce the wood chips of logging residues the system productivity and cost of the CTL harvesting system were 1.6 Gwt/SMH and 89,865 won/Gwt, respectively. The productivity and cost of the WT harvesting system were 2.9 Gwt/SMH and 72,974 won/Gwt, respectively. The WT harvesting productivity increased 1.3times while harvesting cost decreased by 18.7% compared to the CTL harvesting system. The logging residues of wood chips were not suitable for CTL wood chips based on International Organization for Standardization (ISO 17225-4:2021) and South Korea standard (NIFoS, 2020), but the quality (A2, Second class) was improved through screening operation. The WT-unscreened wood chips conformed to NIFoS standard (second class) and did not conform to ISO but were improved through screening operation (Second class). In addition to the energy facility in plant A, all wood chips except CTL-unscreened wood chips were available through drying processing. The WT-unscreened wood chips were the lowest at 99,408 won/Gwt. Plants B, C, and D had higher moisture content than plant A, so WT-unscreened wood chips without drying processing were the lowest at 57,204 won/Gwt. Therefore, the production of logging residues should improve with operation methods that improve the quality of wood chips required for applying the variable biomass and energy facility.

• Resources Recycling
• /
• v.31 no.1
• /
• pp.65-77
• /
• 2022

A study was conducted in Korea on the leaching behavior and possibility of recovery of vanadium and other valuable metals from domestic vanadium titanomagnetite (VTM) by direct acid leaching. In this study, a VTM concentrate containing 0.8% V₂O₅ was used, and the ratio of magnetite to ilmenite was calculated as 1.9:1 by using the HSC program. The leaching behavior of vanadium from the VTM was similar to that of iron, and it was affected by the concentration of sulfuric acid and temperature. Further, titanium could be leached in the form of TiOSO₄ at a temperature higher than 75℃. To improve the leaching efficiency of V, Fe, and Ti in VTM, reductive sulfuric acid and oxidative sulfuric acid leaching were performed. When Na₂SO₃ was used as a reducing agent, the leaching rate of vanadium was 80% of that in that case of leaching by sulfuric acid. Similarly, the leaching rate of titanium increased from 20% to 50%. When Na₂S₂O₈ was used as an oxidation agent, most of the vanadium was leached, and the main residue found by XRD analysis was ilmenite. In studies on the possibility of recovering valuable metals, the selective extraction of metals is hardly achieved by solvent extraction from oxidation leaching solutions; however, in this study, Cyanex 923, a solvation extractant from reductive leaching solutions, could selectively extract Ti.

• The Korean Journal of Nuclear Medicine
• /
• v.32 no.6
• /
• pp.516-524
• /
• 1998

Purpose: Radiolabeled CEA79.4 antibody has a possibility to be used in radioimmunoscintigraphy or radioimmunotherapy of cancer. We investigated the in vitro properties and biodistribution of CEA79.4 antibody labeled with Re-188 or Tc-99m. Materials and Methods: CEA79.4 was reduced by 2-mercaptoethanol to produce-SH residue, and was labeled with Re-188 or Tc-99m. For direct labeling of Tc-99m, methylene-diphosphonate was used as transchelating agent. CEA79.4 in 50 mM Acetate Buffered Saline (ABS, pH 5.3) was labeled with Re-188, using stannous tartrate as reducing agent. In order to measure immunoreactivity and the affinity constant of radiolabeled antibody, cell binding assay and Scatchard analysis using human colon cancer cells SNU-C4, were performed. Biodistribution study of labeled CEA79.4 was carried out at 1, 14 and 24 hr in ICR mice. Results: Labeling efficiencies of Tc-99m and Re-188 labeled antibodies were $92.4{\pm}5.9%$ and $84.7{\pm}4.6%$, respectively, In vitro stability of Tc-99m-CEA79.4 in human serum was higher than Re-188-CEA79.4. Immunoreactivity and affinity constant of Tc-99m-CEA79.4 were 59.2% and $6.59{\times}10^9\;M^{-1}$, respectively, while those of Re-188-CEA79.4 were 41.6% and $4.2{\times}10^9\;M^{-1}$, respectively. After 24 hr of administrations of Re-188 and Tc-99m labeled antibody, the remaining antibodies in blood were 6.32 and 9.35% ID/g respectively. The biodistribution of each labeled antibody in other organs was similar because they did not accumulate in non-targeted organs. Conclusion: In vitro properties and biodistribution of Re-188-CEA79.4 were similar to those of Tc-99m-CEA79.4. It appears that Re-188-CEA79.4 can be used as a suitable agent for radioimmunotheraphy.