• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2003.11a
• /
• pp.368-376
• /
• 2003

In this research, DLC thin films are produced as several hundred nm thickness by PE-CVD method. And then these thin films are estimated tribological characteristics to find out useful possibilities as a protecting film for high-quality function and life extension at MEMs by mechanical properties observation . These are measured thickness and residual stress of DLC coating. Compared after measuring friction coefficient, adhesion force, hardness, cohesive force of coating films. As results all test, we can decide several conclusions. First, friction coefficient decreased, as the load increased. otherwise, friction coefficient increased, as thickness of coating film increased under low load$(1\~50mN)$. Secod, adhesion force increased as thickness of coating films. Third, hardness of coating film is affected by substrate coating film when it is less than thickness of 300nm and it has general hardness of DLC coating film when it is more than thickness of 500nm. Fourth, cohesive force of coating film is complexly affected by hardness, adhesion force, residual stress, etc.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.210-213
• /
• 2002

The Purpose of this study is to know temperature and thermal stress distribution in specimens during processing of WEDM. If it is constant to the cutting speed and the thickness of material, it is very important to the effect of temperature and the thermal stress distribution after cutting processing. This paper show the analysis result of the distribution of temperature and the residual stress along the direction of thickness before processing of WEDM and after when the cooling temperature is$20^{\circ}C$. The maximum temperature of edge of specimens is $1600^{\circ}C$. It has little temperature gradient in the depth which is 5mm away from edge of specimens. Equivalent residual stress is result in 180.7 MPa at maximum temperature.

• Proceedings of the KIEE Conference
• /
• 1998.07g
• /
• pp.2521-2523
• /
• 1998

Freestanding flexible microstructures fabricated from deposited thin films become mechanically unstable when internal stresses exceed critical values. The residual stress and stress gradient of aluminum thin film were examined to make sure of fabricating the reproduceable aluminium structure. For good shape of micro mirror array and microstructures, the experiment was done varying thickness and deposition rate. As the aluminium film thickness increased from 0.8${\mu}m$ to 1.6${\mu}m$, the stress gradient decreased from 11.62MPa/${\mu}m$ to 2.62MPa/${\mu}m$. The residual stress values are from 42.4MPa to 62.24MPa of tensile stresses.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.27 no.2
• /
• pp.103-111
• /
• 2015

In general, no particularly well-established standards have been in place so far, for the method of evaluating the deteriorated level of pipes and ducts of industrial facilities. For that reason, the evaluation depends upon various studies which are based on the analysis of the residual life, thickness thinning, closure rate, and scale thickness that measure a few specific positions of pipes. It also depends upon the expertise in business operation and the specific techniques conducted by the inspection companies and institutions. This research introduces the concept of measuring units per section and the selection method of measurement points per section. Furthermore, specific methodologies were developed to plan and analyze deterioration level of industrial pipes and ducts by engineers and managers using a section map. Consequently, applying the outcomes from this study to the plant equipment of the incineration facility resulted in saving 42% of the repairing and remodeling cost.

• Journal of the Korean institute of surface engineering
• /
• v.43 no.3
• /
• pp.127-131
• /
• 2010

Adhesion of DLC film is very significant property that exhibits wear resistance, chemical inertness and high hardness when being deposited to metal substrate. This study was considered that change adhesion of DLC film produced by Plasma Enhanced Chemical Vapor Deposition can be presented through inserting interlayer (Cr, Si-C:H). The thickness of interlayer was result of changing adhesion and residual stress. It was showed that the maximum 12 N of adhesion is on DLC film of Cr interlayer, and that a tendency is to be increased residual stress depend on the thickness. DLC film of Si-C:H interlayer represented 16 N of adhesion at $1{\mu}m$, whereas adhesion is decreased when the thickness is increased. For the interlayer at multi-layer, it was the best that adhesion of Cr/Si-C:H/DLC film was 33 N. Si-C:H interlayer at DLC film controled adhesion of the whole film. It was relaxed the internal stress of DLC film produced by inserting Cr, Si-C:H interlayer.

• Transactions of Materials Processing
• /
• v.12 no.2
• /
• pp.123-127
• /
• 2003

The cold rolling conditions for the ultra thin steel for tension mask are very important because the residual stress that affects the flatness of strip is generate during the cold rolling. The residual stress in the sheet causes etching curls when it suffers perforation process. The residual stress through the thickness. To estimate the residual stress and deformation due to etching curl. FEM analysis is performed. Numerical simulation employ a ANSY5 5.6 and an elastic-plastic constitutive equation. The simulation results indicate the distribution of residual stress in the rolled sheet can be controlled by selecting the rolling conditions properly.

• Journal of the Korean Society of Safety
• /
• v.23 no.3
• /
• pp.8-11
• /
• 2008

In the present work, the measurement method of residual stresses in thermal barrier coatings(TBCs) which are received the thermal shock is performed numerically. For this, the internal residual stresses are predicted by commercial FEM software ABAQUS because the hole drilling strain gage method measures residual stresses only near the surface of a material. As the results of this study, the residual stresses are linearly increased when the surface temperatures are over $1,200^{\circ}C$. It is also found that the values of residual stress are increased as the coating thickness is thin.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.04a
• /
• pp.176-179
• /
• 2003

This paper deals with the optimum design of thick-walled multi-layered composite tubes by minimizing the process-induced residual stresses under some constraints of structural stiffnesses. An analytic model based on quasi-static thermoelasticity is adopted for the calculation of the residual stresses in the multi-layered composite tubes. The numerical results of optimization show that, in the case of cross-ply CFRP tubes, the residual stresses can be reduced to a certain level by controlling ply thicknesses. However, the optimized tubes may be susceptible to cracking because the transverse residual stress is still large in a strength-based sense. To further suppress the residual stresses, the effects of stacking sequence, wall thickness and axial pretension on the optimum solutions are examined.

• Journal of Welding and Joining
• /
• v.33 no.1
• /
• pp.30-34
• /
• 2015

Residual stresses are inherently introduced into the engineering components during manufacturing including rolling, forging, bending and welding processes. Excessive residual stresses are known to be detrimental to the proper integrity and performance of components. Neutron diffraction has become a well-established technique for the determination of residual stresses in welds. The deep penetration capability of neutrons into most metallic materials makes neutron diffraction a powerful tool for the residual stress measurements through the thickness of the weld specimen. Furthermore, the unique volume-averaged bulk characteristic of the scattering beam and mapping capability in three dimensions is suitable for the engineering purpose. In this presentation, the neutron diffraction measurements of the residual stresses will be introduced and measurement results will highlighted in thick weld plates.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.464-468
• /
• 2008

In most of the passenger side airbag door in hard type IP today is designed with invisible tear-seam line. In order to design the tear-seam invisible, the tear-seam must be designed with required RWT (residual wall thickness) that is just thick enough to be broken by the PAB pressure on deployment and not by other surrounding impact forces. Hence, keeping the right optimum opening force is very important, and finding the right RWT became the key in designing the tear-seam. The study conducted in this paper describes the search for the optimum RWT around the tear-seam by using finite element method and the optimum RWT is suggested for milling type tear-seam having V-shape cross-section.