• Journal of the Korean Society of Safety
• /
• 제10권2호
• /
• pp.17-23
• /
• 1995

Though the magnitude is decreasing, the compressive residual stress is always distributed during fatigue crack growth near the crack tip. This means that the residual stress is released during fatigue crack growth due to the alternative load. ${\Delta}K_{IV}$ is modified by using the initial residual stress and the redistributed residual stress in uniform and various thickness welded specimens. The former is denoted by ${\Delta}K_{IV.eff.i}$ and the latter is denoted by ${\Delta}K_{IV.eff.i}$. ${\Delta}K_{IV.eff.i}$ gives more accurate relations in da/dN vs. ${\Delta}K_{IV}$ curve, however the difference is very small.

• Journal of Welding and Joining
• /
• 제14권5호
• /
• pp.69-77
• /
• 1996

This study aims to analyze the S. I. F. K value upon Mode I cracks in a finite-width plate of varying thickness, which is expressed in terms of width ratio ($\omega$), thickness ratio ($\beta$) and non-dimensional crack length (λ) by using the 2-dimensional finite element method. Then, by comparing the effectiveness of the results obtained by the two finite element methods, it is seen that the 2-dimensional finite element method can be used in order to analyse the S. I. F. K values upon a various thickness model. A model is developed in order to analyze the effects of initial residual stress upon the fatigue crack growth behavior in various thickness welded specimens. In this model, crack growth rate da/dN appears to be come small as the thickness ratio with the same ΔK is increased. Also, in the initial step, as ΔK is increased with crack growth rate is decreased and then increased because the repeated compressive residual stress retards crack growth rate.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• 제27권3호
• /
• pp.159-167
• /
• 2015

In this paper, the errors found in the existed analytical solutions described the mechanism of residual pore-water pressure accumulation were examined and a new analytical was proposed. The new analytical solution was derived by using a Fourier series expansion and separation of variables was verified by comparison with the existed both analytical and numerical solutions and experimental result. The new analytical solution is very simple that there is no need for numerical integration for deep soil thickness. In addition, the solutions of the residual pore-water pressure for finite, deep, and shallow soil thickness reveled that it is possible to approach from finite to shallow soil thickness, but not possible to deep soil thickness because there was discontinues zone between finite and deep soil thickness.

• Transactions on Electrical and Electronic Materials
• /
• 제15권5호
• /
• pp.253-256
• /
• 2014

$Pb(Zr_{0.52}Ti_{0.48})O_3$ thin films of $1.5{\mu}m$ thickness were grown on $Pt/Ti/Gd_3Ga_5O_{12}$ substrate by RF magnetron sputtering at annealing temperatures ranging from $550^{\circ}C$ to $700^{\circ}C$. We evaluated the residual stress, by using a William-Hall plot, as a function of the annealing temperatures of PZT thin film with a constant thickness. As a result, the residual stresses of PZT thin film of $1.5{\mu}m$ thickness were changed by varying the annealing temperature. Also, we measured the hysteresis characteristic of PZT thin films of $1.5{\mu}m$ thickness to evaluate for application of an optoelectronic device.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.633-636
• /
• 2005

Imprint lithography is a promising method for high-resolution and high-throughput lithography using low-cost equipment. As with other nanoimprint methods, ultraviolet-nanoimprint lithography (UV-NIL) resolution appears to be limited only by template resolution, and offers a significant cost of ownership reduction when compared to other next generation lithography (NGL) methods such as EUVL and 157 nm lithography. The purpose of this paper is to suggest optimum values of control parameters of Imprio 100 manufactured by Molecular Imprint, Inc., which is the first commercially available UV-NIL tool, for sound nanoimprint. UV-NIL experiments were performed on Imprio 100 to find dispensing recipe for avoiding air entrapment. Dispensing recipe related to residual layer thickness and uniformity was optimized and 40 nm thick residual layer was achieved.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• 제29권9호
• /
• pp.1169-1174
• /
• 2005

Imprint lithography is a promising method for high-resolution and high-throughput lithography using low-cost equipment. In particular, ultraviolet-nanoimprint lithography (UV-NIL) is applicable to large area imprint easily. We have proposed a new UV-NIL process using an elementwise patterned stamp (EPS), which consists of a number of elements, each of which is separated by channel. Experiments on UV-NIL are performed on an EVG620-NIL using the EPS with 3mm channel width. The replication of uniform sub 70 nm lines using the EPS is demonstrated. We investigate the nonuniformity of residual layer caused by wafer deformation in experiment with varying wafer thickness. Severely deformed wafer works as an obstacle in spreading of dropped resin, which causes nonuniformity of thickness of residual layer. Numerical simulations are conducted to analyze aforementioned phenomenon. Wafer deformation in the process is simulated by using a simplified model, which is a good agreement with experiments.

• Tribology and Lubricants
• /
• 제26권5호
• /
• pp.297-302
• /
• 2010

This study is focused on the resin layer formation of UV imprinting process by changing imprinting pressure and period. The mold shape is made for the process of window open over the pattern transfer area and the imprinting period is assigned as the time just before the UV light curing. The residual layer is measured by changing the imprinting period and pressure magnitude, and the measured data of residual layer provides useful information for the design of the process conditions of imprinting processes.

• Steel and Composite Structures
• /
• 제33권4호
• /
• pp.489-507
• /
• 2019

In order to obtain high bearing capacity and good ductility simultaneously, a structural column with hybrid normal and high strength steel (HNHSS) welded box section has been developed. Residual stress is an important factor that can influence the behaviour of a structural member in steel structures. Accordingly, the magnitudes and distributions of residual stresses in HNHSS welded box sections were investigated experimentally using the sectioning method. In this study, the following four box sections were tested: one normal strength steel (NSS) section, one high strength steel (HSS) section, and two HNHSS sections. Based on the experimental data from previous studies and the test results of this study, the effects of the width-to-thickness ratio of plate, yield strength of plate, and the plate thickness of the residual stresses of welded box sections were investigated in detail. A unified residual stress model for NSS, HSS and HNHSS welded box sections was proposed, and the corresponding simplified prediction equations for the maximum tensile residual stress ratio (${\sigma}_{rt}/f_y$) and average compressive residual stress ratio (${\sigma}_{rc}/f_y$) in the model were quantitatively established. The predicted magnitudes and distributions of residual stresses for four tested sections in this study by using the proposed residual stress model were compared with the experimental results, and the feasibility of this proposed model was shown to be in good agreement.

• The Journal of Korean Academy of Prosthodontics
• /
• 제36권1호
• /
• pp.18-25
• /
• 1998

The purpose of this study was to determine how to use soft relining material by observing an amount of denture displacement according to the different base area of residual ridge and thickness of soft relining material under masticatory force. Stone models that simulated residual ridge were made with different amount of denture base area and denture was fabricated by conventional heat curing resin with usual manner on the model and relined by silicone type soft relining material with different thickness. Specimen was examined the amount of denture displacement by Instron within range of normal occlusal force. The results were as following : 1. The increasing rate of denture displacement was higher than that of soft relining material thickness. 2. The amount of denture displacement decreased 1.7 times when base area became double at same thickness of soft relining material 3. The increasing rate of denture displacement was higher than that of occlusal force

• Journal of the Korean Society for Precision Engineering
• /
• 제25권9호
• /
• pp.38-44
• /
• 2008

Light guide plate is one of most important components which are composed of back light unit, affecting the quality and performance of LCD. Average brightness and uniformity are especially key factors for designing the light guide unit. These qualities are affected and controlled by the pattern being attached to the back of light guide unit. In order to obtain high brightness and uniformity the optimized pattern design is adopted for LGP. In this study, optimized molding condition for LGP with 0.4 mm thickness was obtained by using the Moldflow simulation software and the optimized pattern for better brightness uniformity was designed for the thickness of the 0.4 mm by trial and error method. The brightness was measured for the different LGP thicknesses and the residual stress analysis was performed for 0.4 mmthickness by the photoelasticity and the results are compared with 0.5 mm, 0.6 mm thickness.