• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1489-1492
• /
• 2005

Compared to other nano-patterning techniques, Nano imprint Lithography (NIL) has some advantages of high throughput and low process cost. To imprint low temperature and pressure, UV Nano imprint Lithography, which using the monomer based UV curable resin is suggested. Because fabrication of high fidelity pattern on topographical substrate is difficult, bi-layer Nano imprint lithography, which are consist of easily removable under-layer and imprinted pattern, is being used. If residual layer is not remained after imprinting, and under-layer is removed by oxygen RIE etching, we might be able to fabricate the bi-layer pattern for easy lift-off process.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.28 no.3
• /
• pp.156-165
• /
• 2005

A new heuristic algorithm for the heterogeneous single container loading problem is proposed in this paper, This algorithm fills empty spaces with the homogeneous load-blocks of identically oriented boxes and splits residual space into three sub spaces starting with an empty container. An initial loading pattern is built by applying this approach recursively until all boxes are exhausted or no empty spaces are left. In order to generate alternative loading patterns, the load-blocks of pattern determining spaces are replaced with the alternatives that were generated on determining the load-blocks. An improvement algorithm compares these alternatives with the initial pattern to find improved one. Numerical experiments with 715 test cases show the good performance of this new algorithm, above all for problems with strongly heterogeneous boxes.

• Journal of Sensor Science and Technology
• /
• v.30 no.5
• /
• pp.273-278
• /
• 2021

Here, we studied the change in the mechanical stiffness of a diaphragm according to the corrugation pattern. The diaphragm consists of a silicon oxide and nitride double layer; a corrugation pattern was formed by dry etching, and the diaphragm was released by wet etching. The fabrication of the thin film was verified using focused ion beam and scanning electron microscopy images. The mechanical stiffness of the diaphragm was obtained by measuring the surface vibration using a laser Doppler vibrometer while applying external sound pressure. Flat squares, diaphragms with square corrugations, and circular corrugation patterns were measured and compared. The stiffness of the diaphragm with a corrugation structure was found to be smaller than that without a corrugation structure; in particular, circular corrugation showed a better effect because of the high symmetry. Furthermore, the effect of corrugation was theoretically predicted. The proposed corrugated diaphragm showed comparable flexibility with the state-of-the-art MEMS microphone diaphragm.

• Journal of Broadcast Engineering
• /
• v.15 no.5
• /
• pp.653-664
• /
• 2010

Generally existing video codec employs entropy coding to deal with residual signals with considering temporal and spatial properties. Scalable Video Coding(SVC) which is extension of H.264/AVC has three technical concepts for removing redundancies between inter-layers. In spite of using novel prediction method between inter-layers in SVC, it is still using same entropy coding method to residual signals. According to the studies, the residual obtained by inter-layer prediction technique has different features of residual signal acquired by spatial or temporal prediction technique. In this paper, we propose an efficient entropy coding method which codes the residual signal obtained by inter-layer prediction with regarding its features adequately. We re-designed the Coded Block Pattern(CBP) table suitably for inter-layer texture prediction. The experiments show that the proposed method can further reduce the BD-Bitrate up to average 2.20% in 4CIF and 1.14% in CIF resolution compared to the existing JSVM 9.18.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.26 no.2
• /
• pp.123-130
• /
• 2013

In this paper, the delamination and failures in frequency selected surface(FSS) caused by residual stresses in the FSS embedded hybrid composites due to the difference between the coefficients of thermal expansion of components and the transmission characteristic changes due to deformation of FSS patterns by residual stresses were studied. FSS may have different electromagnetic characteristics depending on the type of element, design variables, and arrangement. Design variables of dipole FSS were determined using PSO(Particle Swarm Optimization) to obtain the transmission characteristic for the target resonant frequency. Subsequently, the design variables of other types of N-pole(tripole, cross dipole, and Jerusalem cross) were determined based on the dimensions of the dipole for the comparisons of residual stresses of FSS embedded composite structures and transmission characteristics. In addition, effects of FSS pattern, and stacking sequence of composite laminates were considered.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.4
• /
• pp.1900-1907
• /
• 2012

Since the subpanels of polygonal-section shell have the corners of an obtuse angle larger than 90 degree unlike general plate or box-section structures, this could have an influence on forming nodal lines against local plate buckling or stress distributions. However, there is not sufficient material in the relevant study results or design recommendations. The very feasible models of the initial imperfections were acquired through the literature studies and then the parametric studies were conducted along with the initial imperfection models by using the finite element method. The parameters like the size of residual stresses, the portion of compressive residual stresses, and steel grades were considered. From the parametric studies, it was found that the maximum residual stress is more influential factor than the distribution pattern of residual stresses. In addition, The design strength equations for the simply supported plates can be applicable to the determination of the local buckling strength of the polygonal cross-section shell structures.

• Composites Research
• /
• v.24 no.1
• /
• pp.37-44
• /
• 2011

In this paper, Particle Swarm Optimization(PSO) is applied to the design of the Frequency Selective Surface(FSS) and residual stresses of hybrid radome is predicted. An equivalent circuit model with Square Loops arrays was derived and then PSO was applied for acquiring the optimized geometrical parameters with proper resonant frequency. Residual stresses occur in the FSS embedded composite structures after cocuring and have a great influence on the strength of the FSS embedded composite structures. They also effect transmission quality because of delamination. Therefore, the thermal residual stresses of FSS embedded composite structures were analyzed using finite element analysis with considering the effects of FSS pattern, and composite stacking sequence.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.34 no.1
• /
• pp.18-22
• /
• 2014

Residual stresses that occur during the welding process, are the main cause of failure and defects in welded structures. This paper, presents the use of an electronic processing laser speckle interferometer to measure the residual stress of a welded pipe for a nuclear power plant. A tensile testing machine was used to evaluate a welded pipe that failed in compression. The inform plane deformation and modulus of elasticity of the base metal and welds were measured using an interferometer. Varying the load on the welded pipe had a larger effect on the deformation of the base metal the other properties of the base metal and welds. The elastic moduli of the base metal and weld of the welded pipe were 202.46 and 212.14 GPa, respectively, the residual stress was measured to be 6.29 MPa.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.4
• /
• pp.223-231
• /
• 2022

Residual stress that can occur during the metal additive manufacturing process is an important factor that must be properly controlled for the precise production of metal parts through 3D printing. Therefore, in this study, the factors affecting these residual stresses were investigated using an experimental method. For the experiment, a specimen was manufactured through an additive manufacturing process, and the amount of deformation was measured by cutting it. By appropriately calibrating the measured data using methods such as curve fitting, it was possible to quantitatively analyze the effect of process parameters and metal powder reuse on deformation due to residual stress. From this result, it was confirmed that the factor that has the greatest influence on the magnitude of deformation due to residual stress in the metal additive manufacturing process is whether the metal powder is reused. In addition, it was confirmed that process parameters such as laser pattern and laser scan angle can also affect the deformation.

• Journal of Korean Society for Atmospheric Environment
• /
• v.27 no.6
• /
• pp.650-662
• /
• 2011

The statistical tools such as empirical orthogonal function (EOF), and singular value decomposition (SVD) have been applied to analyze the characteristic of air pollutant over southeast Asia as well as to evaluate Zimeke's tropospheric column ozone (ZTO) determined by tropospheric residual method. In this study, we found that the EOF and SVD analyses are useful methods to extract the most significant temporal and spatial pattern from enormous amounts of satellite data. The EOF analyses with OMI $NO_2$ and OMI HCHO over southeast Asia revealed that the spatial pattern showed high correlation with fire count (r=0.8) and the EOF analysis of CO (r=0.7). This suggests that biomass burning influences a major seasonal variability on $NO_2$ and HCHO over this region. The EOF analysis of ZTO has indicated that the location of maximum ZTO was considerably shifted westward from the location of maximum of fire count and maximum month of ZTO occurred a month later than maximum month (March) of $NO_2$, HCHO and CO. For further analyses, we have performed the SVD analyses between ZTO and ozone precursor to examine their correlation and to check temporal and spatial consistency between two variables. The spatial pattern of ZTO showed latitudinal gradient that could result from latitudinal gradient of stratospheric ozone and temporal maximum of ZTO in March appears to be associated with stratospheric ozone variability that shows maximum in March. These results suggest that there are some sources of error in the tropospheric residual method associated with cloud height error, low efficiency of tropospheric ozone, and low accuracy in lower stratospheric ozone.