• 한국수자원학회논문집
• /
• 제34권6호
• /
• pp.725-733
• /
• 2001

본 연구에서는 모형배수지를 이용하여 유출량의 변동여부와 도류벽의 설치여부에 따른 유출수의 잔류염소농도의 변화를 추적하였다. 모형배수지의 실험결과를 고찰해 보면, 유출량을 변동시킨 경우에 있어서 도류벽이 없을 때와 도류벽이 2개 있을 때, 유출수의 평균 잔류염소농도의 차이가 유출량을 일정하게 유지한 경우에 비하여 줄어 들었다. 이는 유출량 변동의 영향에 의한 것으로 유출량의 변동이 심한 배수지에 있어서는 유출량의 변동이 심하지 않은 정수지에서 보다는 도류벽 설치의 효과가 작은 것으로 판단된다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 추계학술발표대회 논문집
• /
• pp.261-264
• /
• 2002

Interfacial evaluation, damage sensing and cure monitoring of single carbon fiber/thermosetting composite with different curing processes was investigated using electro-micromechanical test. After curing, residual stress was monitored by measurement of electrical resistance (ER) and then it was compared to correlate with various curing processes. In thermal curing, curing shrinkage appeared significantly by matrix shrinkage and residual stress due to the difference in thermal expansion coefficient (TEC). The change in electrical resistance (ΔR) on thermal curing was higher than that on ultraviolet (UV) curing. For thermal curing, apparent modulus was the highest and reaching time until same strain was faster. So far thermal curing shows strong durability on the IFSS after boiling test.

• Journal of Welding and Joining
• /
• 제3권2호
• /
• pp.16-26
• /
• 1985

Post weld heat treatment(PWHT), at more than 600.deg. C, is essential to remove residual stress and hydrogen in weld HAZ and improve fatigue characteristics. However, residual stress during PWHT is responsible for PWHT embitterment and it promotes precipitation of impurities to grain boundary. In this paper, the effect of stress simulated residual stress on fatigue failure was evaluated by fatigue test, microhardness test and fractograph. The obtained results are summarized as follows; (1) The fatigue crack growth rate(da/dN) of parent and heat treated parent was affected by microstructure due to heat treatment and it depended on stress intensity factor (.DELTA.k). (2) The fatigue strength of weld HAZ was dependent on applied stress during PWHT and da/dN after PWHT was slower than as-weld. (3) Softening amount of weld HAZ was bigger than any other due to PWHT. Hardness value of weld HAZ was affected by heat treatment under the applied stress of 10 $kgf/mm^2$, but beyond 20 $kgf/mm^2$ it was increased by the applied stress rather than heat treatment. (4) Beyond the applied stress of 20 $kgf/mm^2$ during PWHT, intergranular fracture surface was observed and its amount was increased with applied stress during PWHT. (5) Effect of applied stress during PWHT on aspect of fracture surface was larger rather than that on fatigue crack growth behavior.

• 설비공학논문집
• /
• 제26권11호
• /
• pp.535-540
• /
• 2014

This paper investigates the exhaust effectiveness of smoke, in the case of fire in a large atrium space. Numerical analysis was conducted to simulate transient fire growth in a test room, modeled by the Murcia atrium fire test. Various indices representing the exhaust performance of the exhaust system were obtained, such as the height of the smoke layer, and the instantaneous and accumulative capture efficiency of the smoke. The residual life time of smoke from the fire was also obtained, by injecting tracer gases at the fire location, depending on the airflow rate, and the location of the exhausts. The capture efficiency based on smoke concentration at the exhausts exhibits how much smoke can be removed by the exhaust system; whereas, the exhaust effectiveness based on residual life time indicates how rapidly the smoke can reach the exhaust locations, before being exhausted. The definitions and meanings of the indices to be used in representing the exhaust performance of a smoke exhaust system installed in a large space are discussed.

• 한국지반공학회지:지반
• /
• 제8권2호
• /
• pp.21-30
• /
• 1992

말뚝의 주면마찰력은 전체 지지력중 상당한 하중을 지지할 수 있으나 실제 설계시에는 무시되는 경우가 많이 있다. 주면마찰력을 설계에 반영할 경우에도 계산결과의 신뢰도는 매우 낮은 것이 현실이다. 국내의 사정은, 설계 자료로 활용할 수 있는 것은 표준관입시험 결과뿐인 경우가 대부분으로 빈곤하며 특히 국내에 많은 화강암, 편마암의 풍화잔류토에 관해서는 설계자료가 극히 희박해 외국에 비해 열악하다. 최근에 국내에서 개발된 간편한 말뚝재하시험(simple pile loading test: SPLT)의 사용은 선단지지력과 주면마찰력의 별도 측정이 가능하도록 하였다. 본 연구에서는 풍화잔류토 지반에서의 SPLT 결과를 분석하여 N값에 의한 새로운 설계관계식을 제안하였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 추계 학술발표회 제16권2호
• /
• pp.553-556
• /
• 2004

This paper is to investigate the spalling and fire endurance of high performance RC column member with PP fiber and lateral confinement of metal lath and non fire resistance removal type form. According to test results, combination of PP fiber and metal lath as well as use fire resistance non removal type form had favorable fire resistance by discharging internal vapour pressure and lateral confining. After fire endurance test, compressive strength decreased markedly caused by internal expansion pressure and crack. Residual strength of plain concrete was decreased to $22\%$. The use of PP fiber and lateral confinement of metal lath and non removal type form enhanced the residual strength above $40\%$. Especially, the combination of $0.1\%$ of PP fiber and lateral confinement with the level of 2.3T exhibited more than $51\%$ of residual strength. Therefore, to improve fire endurance and spalling resistance, the combination of $0.1\%$ of PP fiber and metal lath with 2.3T can be the proper measure.

• 전자공학회논문지B
• /
• 제30B권1호
• /
• pp.63-71
• /
• 1993

An efficient RVQ image coding method is proposed using the segmentation-based coding and CVQ techniques. In the proposed method the residual image, the difference between an original image and the synthesized one obtained from the segmentation-based coding, is first dividel into $\times$4 subblocks. They are then individually coded in the spatial domain using a simple CVQ. Experimental results show that the proposed method yields better quality of the reconstructed images in both PSNR and subjective test over the basic VQ and SMVQ.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1997년도 추계학술대회 논문집
• /
• pp.322-327
• /
• 1997

This paper investigates the effects of shot peening on mechanical properties of SAE 9254, which is a spring steel used for the suspension system of automobiles. Rotary Bending Fatigue test is accomplished and the results are summarized as fellows : 1. The tensile strength and the hardness do not change so much. 2. The layer of highly residual stress is obtained by multi-stage shot peening. 3. The fatigue strength seems to be improved by residual stress. 4. The fatigue strength of un-peened and multistage shot peened material are 425 MPa and 756 MPa, respectively.

• 한국산업융합학회 논문집
• /
• 제10권3호
• /
• pp.143-147
• /
• 2007

In recents years, the statistical properties has become an important quantity for reliability based design of a component. The effects of the materials and test conditions for parameter estimation in residual strength degradation model are studied in carbon/epoxy laminate. It is shown that the correlation between the experimental results and the theoretical prediction on the fatigue life distribution using the life distribution convergence method is very reasonable.

• 전기의세계
• /
• 제31권5호
• /
• pp.368-374
• /
• 1982

This paper describes a combined algorithm for short-term-load forecating. One of the specific features of this algorithm is that the base, weather sensitive and residual components are predicted respectively. The base load is represented by the exponential smoothing approach and residual load is represented by the Box-Jenkins methodology. The weather sensitive load models are developed according to the information of temperature and discomfort index. This method was applied to Korea Electric Company and results for test periods up to three years are given.