• Aerospace Engineering and Technology
• /
• v.2 no.2
• /
• pp.45-49
• /
• 2003

A Bake-Out test for STSAT-1 FM(Flight Model) was performed in a Bake-Out Chamber at SITC(Satellite Integration & Test Center) in KARI(Korea Aerospace Research Institute). The purpose of this test is to measure and analyze the outgassing rate to affect the optical equipment(FIMS) and to eliminate contaminants through the high temperature bake-out. This Bake-Out test is composed of three parts which are honeycomb panels & harnesses(Batch 1), an assembled satellite(Batch 2), and a disassembled satellite(Batch 3). For each test, quantitative and qualitative measurements and analysis were performed using TQCM(Thermoelectric Quartz Crystal Microbalance) and RGA(Residual Gas Analyzer.)

• Advances in concrete construction
• /
• v.10 no.2
• /
• pp.113-125
• /
• 2020

This paper presents experimental results on bond-slip behavior of steel reinforced high-strength concrete (SRHC) after exposure to elevated temperatures. Three parameters were considered in this test: (a) high temperatures (i.e., 20℃, 200℃, 400℃, 600℃, 800℃); (b) concrete strength (i.e., C60, C70, C80); (c) anchorage length (i.e., 250 mm, 400 mm). A total of 17 SRHC specimens subjected to high temperatures were designed for push out test. The load-slip curves at the loading end and free end were obtained, the influence of various variation parameters on the ultimate bond strength and residual bond strength was analyzed, in addition, the influence of elevated temperatures on the invalidation mechanism was researched in details. Test results show that the shapes of load-slip curves at loading ends and free ends are similar. The ultimate bond strength and residual bond strength of SRHC decrease first and then recover partly with the temperature increasing. The bond strength is proportional to the concrete strength, and the bond strength is proportional to the anchoring length when the temperature is low, while the opposite situation occurs when the temperature is high. What's more, the bond damage of specimens with lower temperature develops earlier and faster than the specimens with higher temperature. From these experimental findings, the bond-slip constitutive formula of SRHC subjected to elevated temperatures is proposed, which fills well with test data.

• Journal of Ocean Engineering and Technology
• /
• v.13 no.3 s.33
• /
• pp.68-76
• /
• 1999

The welding residual stresses produced by the welding frequently caused a crack and promote stress corrosion etc. in HAZ(heat affected zone) contained with external load and weakness of material. Therefore, PWHT(post welding heat treatment) is widely used to reduce wekdubg residuss, to relax hardening of heat affected zone and to get rid of impurity. In this study, in order to define the effect on shappes of T-welded joint, during the post welding heat treatment, we have carried out numerical analyses on the several test pieces by using computer program which was based on thermal-elasto-plato-plasto-creep theories for the study. The main results obtained form this study is as follows: 1) The mechanical difference for change the thickness of plate and groove angle did not appear. 2) The distribution modes of welding residual stresses are same on the all test specimens during the post welding heat treatment. 3) In a mecharical point of view, minimum groove groove angle($40^{circ}$) is more suitable than maximum groove angle($60^{circ}$). 4) Therefore, it is appropriate to minimize the size of groove shape in strength and safety.

• Journal of Welding and Joining
• /
• v.26 no.3
• /
• pp.67-73
• /
• 2008

Fatigue life evaluation of welded structures in a range of high cycles is one of the most difficult problems since extremely small plastic deformation and damage occur during the loading cycles. Moreover, it is very difficult to identify the strong non-linearities of welding, inducing residual stress. In this paper, numerical fatigue test method for welded structures was developed using continuum damage mechanics with inherent strain. Recently, continuum damage mechanics, which can simulate both crack initiation at the micro-scale level and crack propagation at the meso-scale level, has been adopted in the fracture related problem. In order to consider the residual stresses in the welded strictures, damage calculation in conjunction with welding, inducing inherent strain, was proposed. The numerical results obtained from the damage calculation were compared to experimental results.

• Korean Journal of Veterinary Service
• /
• v.21 no.1
• /
• pp.13-20
• /
• 1998

This survey was carried out to detect the residual antibiotics and sulfonamides in emergency slaughtered cattle(n=265) from slaughter houses in Kyeonggi province by EEC 4-plates method, Charm II and HPLC. The results were summarized as follows ; 1. Antimicrobial substances were detected from 24 samples(9.1%) by EEC 4-plates method and the detection ratio were highest in summer(13.8%). 2. Twenty-two of the 24 positive samples were classified as sulfonamide(34.4%), TCs(31.3%), $\beta$-lactam(23.5%) and aminoglycoside(9.3%) by Charm II test. 13(59.1%) of the 22 samples contained single agent and 9 samples(40.9%) contained 2 or more agents. 3. Oxytetracycline(27.3%), penicillin G (27.3%) and sulfathiazole(18.2%) were detected in 20 from 22 samples by the HPLC and Charm II test. 4. The residual concentration of oxytetracycline, penicillin G and sulfonamide were 0.29~9.30 ppm, 0.05~9.58 ppm and 0.04~7.59 ppm, respectively and 19 samples(7.2%) were exceeded tolerance levels.

• Journal of the Korean Geosynthetics Society
• /
• v.5 no.1
• /
• pp.1-7
• /
• 2006

Despite a number of advantages of reinforced earth walls over conventional concrete retaining walls, there exit concerns over long-term residual deformation when used as part of permanent structures. In view of these concerns, time-dependant deformation characteristics of geosynthetic reinforced modular block walls under sustained loads were investigated using reduced-scale model tests. The results indicated that a sustained load can yield appreciable magnitude of residual deformation, and that the magnitude of residual deformation depends on the loading characteristic as well as reinforcement stiffness.

• International Journal of Safety
• /
• v.1 no.1
• /
• pp.24-27
• /
• 2002

Recently the steel parts used in automobiles are required to be used under high stress more than ever before due to the need of keeping the weight down. To achieve this requirement of the high strength steel, it must be necessary to decrease inclusion contents and surface defects as like decarburization, surface roughness etc. In this study, the surface conditions are measured to know the influence on fatigue properties by two cases of two-stage shot peening and single-stage shot peening. And for this study, three kinds of spring steel (JISG408l-SUP7, SAE 9254 and DIN 50CrV4) are shaped. This study shows the outstanding improvement of fatigue properties at the case of two-stage shot peening in the rotating bending fatigue test and it results from (1) decreasing the surface roughness (2) unchanging the surface hardness (3) increasing the compressive residual stress. Moreover, results also show fatigue failures originated at the inclusion near the surface, and this inclusion type is turned out to be an alumina of high hardness.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.2
• /
• pp.35-42
• /
• 2008

The compressive residual stress due to shot peening process can increase the intrinsic fatigue strength of surface and therefore would be beneficial in reducing the probability of fatigue damage. However, it was not known that the effect of shot peening on corrosion environment. In this study, the influence of shot peening and corrosion condition on corrosion property was investigated on immersed in 3.5% NaCl, 10% $HNO_3$+3% HF, 6% $FeCl_3$. The immersion test was performed with two kind of specimens. The immersion test periods were carried out on performed 360days. Corrosion potential and weight loss were investigated from experimental results. From these results, the effect of shot peening on the corrosion characteristics was evaluated.

• Journal of Applied Reliability
• /
• v.18 no.3
• /
• pp.220-228
• /
• 2018

Purpose: The purpose of this study is to investigate the tail behavior of the life distribution which exhibits an increasing failure rate or other positive aging effects after a certain time point. Methods: We characterize the tail behavior of the life distribution with regard to certain reliability measures such as failure rate, mean residual life and reliability function and derive several stochastic properties regarding such life distributions. Also, utilizing an L-statistic and its asymptotic normality, we propose new nonparametric testing procedures which verify if the life distribution has an increasing tail failure rate. Results: We propose the IFR-Tail (Increasing Failure Rate in Tail), DMRL-Tail (Decreasing Mean Residual Life in Tail) and NBU-Tail (New Better than Used in Tail) classes, all of which represent the tail behavior of the life distribution. And we discuss some stochastic properties of these proposed classes. Also, we develop a new nonparametric test procedure for detecting the IFR-Tail class and discuss its relative efficiency to explore the power of the test. Conclusion: The results of our research could be utilized in the study of wide range of applications including the maintenance and warranty policy of the second-hand system.

• Steel and Composite Structures
• /
• v.22 no.2
• /
• pp.353-368
• /
• 2016

This paper extends our recent work on the fatigue behavior of stud shear connectors in steel and recycled tyre rubber-filled concrete (RRFC) composite beams. A series of 16 fatigue push-out tests were conducted using a hydraulic servo testing machine. Three different recycled tyre rubber contents of concrete, 0%, 5% and 10%, were adopted as main variable parameters. Stress amplitudes and the diameters of studs were also taken into consideration in the tests. The results show that the fatigue lives of studs in 5% and 10% RRFC were 1.6 and 2.0 times greater of those in normal concrete, respectively. At the same time, the ultimate residual slips' values of stud increased in RRFC to highlight its better ductility. The average ultimate residual slip value of the studs was found to be equal to a quarter of studs' diameter. It had also been proved that stress amplitude was inversely proportional to the fatigue life of studs. Moreover, the fatigue lives of studs with large diameter were slightly shorter than those of smaller ones and using larger ones had the risk of tearing off the base metal. Finally, the comparison between test results and three national codes was discussed.