• 대한토목학회논문집
• /
• 제30권1A호
• /
• pp.53-59
• /
• 2010

최근 들어 적외선을 이용하여 콘크리트 구조물의 결함 또는 공동 등을 평가하려는 비파괴 연구가 활발하게 진행되고 있으며, 이는 유지관리기법의 중요한 부분을 이루고 있다. 적외선 화상분석(Infrared Thermography)을 콘크리트 표면에 적용할 경우, 콘크리트의 표면온도는 표면을 구성하는 재질과 열적특성(비열, 열전도율, 열전달율)에 따라 그 응답이 다르게 나타나게 된다. 서로 다른 배합을 가지는 시멘트 모르타르에서는 공극률이 다르게 구성되고, 표면에서 공극률의 차이는 열에 노출된 뒤, 냉각되는 과정에서 열적 거동이 다르게 평가된다. 한편 이러한 공극률은 강도 및 염화물 확산계수와 같은 역학적/내구적 특성에 영향을 주기도 한다. 본 연구에서는 외부에서 열을 가하여 측정하는 능동방식(active type)을 이용하여, 표면의 온도변화를 분석하였다. 물-시멘트비 55%와 65%인 시멘트 모르타르 시편을 제작하였으며, 공극률, 압축강도, 염화물 확산계수 등의 물리적 특성값들이 평가되었다. 이후 동일한 실내조건(온도 $20{\sim}22^{\circ}C$, 습도 55-60%)에서 적외선 화상분석 기법을 적용하였다. 시간의 경과에 따라 공극을 많이 포함하는 시편의 경우, 표면 온도가 상대적으로 증가하였으며, 온도가 일정해지는 시점(임계시점)이 단축되고 있음을 확인할 수 있었다. 이러한 특성은 콘크리트와 같이 공극과 골재를 가지고 있는 복합재료의 품질 평가에 적용할 수 있음을 시사한다. 한편 공극률과 실험상수를 고려하여, 공극률에 따라 변화하는 임계시간에 대한 계산식을 제안하였다. 본 논문에서는 시멘트 모르타르의 공극량의 변화에 따른 물리적 변화와 이에 따른 열특성 변화가 논의될 것이다.

• 한국어병학회지
• /
• 제12권1호
• /
• pp.32-41
• /
• 1999

오존처리 해수중에 함유하는 잔류 옥시던트(TRO)가 양식 넙치의 생존, 혈액성상과 삼투질 농도, 산소소비 및 아가미 조직에 미치는 독성 영향을 조사하였다. TRO에 노출된 넙치의 48-hr 및 96-hr $LC_{50}$은 각각 26.4 와 22.3ppb이었고, 47ppb에서는 3시간 이내에 모두 치사하였으나 13ppb에서는 96시간 동안 폐사발생이 없었다. TRO 24~39ppb 농도범위에 노출된 넙치의 hematocrit, 헤모글로빈, 적혈구 수, 혈중 sodium과 chloride 이온 및 삼투압 농도는 TRO 농도가 높을수록 유의하게 증가하였고, 아가미 조직은 아가미 상피층이 모세혈관으로부터 박리되고, 괴사와 상피새포의 증생이 관찰되었다. 산소소비율은 TRO 농도가 높고, 노출이 계속될수록 감소하였다. 13ppb에서는 아가미 조직과 생리상태에 미치는 변화는 관찰되지 않았으나 혈당은 유의하게 증가하였다. 그러나 활성탄으로 TRO를 제거한 대조구에서는 오존의 독성 영향은 관찰되지 않았다. 잔류오존에 노출된 넙치는 삼투질 농도의 생리적 불균형 및 아가미 손상과 상피세포의 증생에 의한 산소섭취 부족이 치사를 유발하는 것으로 나타났다. 본 연구의 결과 해산어 양식장에서 오존을 사용할 경우에는 오존처리수중의 TRO는 제거하여야 하며, 비록 저농도라도 장기간 노출되면 양식어류의 생존과 생리상태에 미치는 영향은 현저할 것으로 평가되었다.

• Structural Engineering and Mechanics
• /
• 제30권6호
• /
• pp.713-732
• /
• 2008

Serviceability and durability of the concrete members can be seriously affected by the corrosion of steel rebar. Carbonation front and or chloride ingress can destroy the passive film on rebar and may set the corrosion (oxidation process). Depending on the level of oxidation (expansive corrosion products/rust) damage to the cover concrete takes place in the form of expansion, cracking and spalling or delamination. This makes the concrete unable to develop forces through bond and also become unprotected against further degradation from corrosion; and thus marks the end of service life for corrosion-affected structures. This paper presents an analytical model that predicts the weight loss of steel rebar and the corresponding time from onset of corrosion for the known corrosion rate and thus can be used for the determination of time to cover cracking in corrosion affected RC member. This model uses fully the thick-walled cylinder approach. The gradual crack propagation in radial directions (from inside) is considered when the circumferential tensile stresses at the inner surface of intact concrete have reached the tensile strength of concrete. The analysis is done separately with and without considering the stiffness of reinforcing steel and rust combine along with the assumption of zero residual strength of cracked concrete. The model accounts for the time required for corrosion products to fill a porous zone before they start inducing expansive pressure on the concrete surrounding the steel rebar. The capability of the model to produce the experimental trends is demonstrated by comparing the model's predictions with the results of experimental data published in the literature. The effect of considering the corroded reinforcing steel bar stiffness is demonstrated. A sensitivity analysis has also been carried out to show the influence of the various parameters. It has been found that material properties and their inter-relations significantly influence weight loss of rebar. Time to cover cracking from onset of corrosion for the same weight loss is influenced by corrosion rate and state of oxidation of corrosion product formed. Time to cover cracking from onset of corrosion is useful in making certain decisions pertaining to inspection, repair, rehabilitation, replacement and demolition of RC member/structure in corrosive environment.

• 한국수산과학회지
• /
• 제34권5호
• /
• pp.521-525
• /
• 2001

국내에서 다량 생산되는 갈조류인 미역포자엽, 다시마, 톳, 모자반으로부터 fucoidan을 추출, 분획하여 Pb와 Cd의 흡착 특성을 조사하였다. 4종의 갈조류에서 추출한 fucoidan의 분획물 모두 Pb의 흡착량이 Cd보다 높았으며, 시료간에는 미역포자엽 분획물 (Fr-3.0)이 Pb와 Cd 모두 흡착력이 상대적으로 우수하였다. pH와 농도 변화에 따른 홉착력의 변화는 $C_f$ (잔류농도)가 50mg/L까지는 pH 간 차이가 없었으나, 농로가 증가함에 따라 pH 5.5 처리구가 다른 처리구에 비하여 흡착량이 증가하였다. 실험을 통하여 얻은 Pb 와 Cd의 최대 흡착량은 pH 5.5에서 각각 94mg/g ($C_f$164mg/L), 64mg/g ($C_f$197mg/L)였으며 Langmuir sorption model을 통해 구한 최대 흡착량은 pH 5.5에서 각각 178mg/g, 122mg/g이었다. Cd 공존시 Pb 흘착량은 $C_f$가 낮을 범위에서는 변화가 없었으나 $C_f$가 증가함에 따라 공존 이온의 흡착 방해로 인하여 감소하였다.

• 대한환경공학회지
• /
• 제38권8호
• /
• pp.428-434
• /
• 2016

본 연구에서는 하수 내 인 제거 시 티타늄계열 응집제의 인 제거특성을 알아보기 위해 알루미늄계열 응집제와 비교하였다. Jar-tester를 이용하여 다양한 OH/Ti 몰비(B값)의 응집제를 투여하여 실험을 진행하였다. 초기 인 농도가 증가할수록 처리 후 $PO_4-P$ 농도가 0.2 mg P/L 이하에 도달하기 위한 [Ti]/[P]는 감소하였다. T-P 제거효율은 응집제 주입량이 증가할수록 높아졌지만, 최고 제거효율에 도달한 후에는 B값에 관계없이 감소하였다. 반면에 $PO_4-P$ 제거율은 최고점에 도달한 후 B값에 상관없이 일정하게 유지하는 경향이 나타났다. 동일한 인 제거효율에서 Ti계열 응집제의 주입량은 Al계열 응집제보다 약 2배정도 높았다. 또한, Ti계열 응집제의 B값에 따라 인제거효율에 영향을 미쳤다.

• 상하수도학회지
• /
• 제32권1호
• /
• pp.47-53
• /
• 2018

This study investigated phosphorus removal from secondary treated effluent using coagulation-membrane separation hybrid treatment to satisfy strict regulation in wastewater treatment. The membrane separation process was used to remove suspended phosphorus particles after coagulation/settlement. Membrane separation with $0.2{\mu}m$ pore size of micro filtration membrane could reduce phosphorus concentration to 0.02 mg P/L after coagulation with 1 mg Al/L dose of polyaluminum chloride (PACl). Regardless of coagulant, the residual concentration of phosphorus decreased as the dose increased from 1.5 to 3.5 mg Al/L, while the target concentration of 0.05 mg P/L or less was achieved at 2.5 mg Al/L for the aluminum sulfate (Alum) and 3.5 mg Al/L for PACl. Moreover, alum showed better membrane flux as make bigger particles than PACl. Alum showed a 40% of flux decrease at 2.5 mg Al/L dose, while PACl indicated a 50% decrease of membrane flux even with a higher dose of 3.5 mg Al/L. Thus, alum was more effective coagulant than PACl considering phosphorus removal and membrane flux as well as its dose. Consequently, the coagulation-membrane separation hybrid treatment could be mitigate regulation on phosphorus removal as unsettleable phosphorus particles were effectively removed by membrane after coagulation.

• 대한화장품학회지
• /
• 제25권4호
• /
• pp.123-131
• /
• 1999

Liquid crystal known as a rheological barrier to coalescence of oil droplets, increases emulsion stability, water-holding capacity and promotes active material penetration to skin. Some investigation for its rheological characteristics have been reported but its relations to consumer perception have been rarely published. In this study, oil/water emulsion and oil/liquid crystal/water systems were manufactured using the same composition or Behenyltrimethylammonium chloride/Cetostearyl alcohol/Lanolin oil. and rheological properties or each system were investigated with Cone and Plate rheometer. The formation of liquid crystalline phase was observed with polarized microscope and Differential Scanning Calorimeter. Continuous shear experiment, creep, yield and water holding capacity were measured for oil/water and oil/liquid crystal/water systems. The results were compared with sensory evaluations. Oil/liquid crystal/water system showed higher,viscosity at the same shear rate. higher viscoelasticity and higher yield stress than oil/water system. These properties were expected to show good spreadability and excellent richness without waxiness in hair can: products of creme type. This expectation was consistent with the results of sensory experiments. Water-holding capacity was evaluated by measuring residual water of specimens at specific temperature and relative humidity. Oil/liquid crystal/water system was proved to have higher ability to hold water in comparison with oil/water system. The results indicated that oil/liquid crystal/water system was of benefit to rheological properties creme type hair care products.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2006년도 PAN PACIFIC CONFERENCE vol.1
• /
• pp.111-116
• /
• 2006

The microstickes control effects of some fixing agents, including an inorganic PAC, an organic polyamine (PA) and polydiallydimethyl ammonium chloride (Pdadmac), and a high cationic starch (HCS), were investigated, together with their effects on wet end performances and physical properties of handsheets. Despite that the HCS and Pdadmac had lower cationic charge densities than the PA and PAC (the HCS being even lower), they gave higher zeta potentials to fibers, and lower turbidities, cationic demands and residual COD contents to the pulp liquid phases than the PA and PAC did. In all cases, the HCS showed even better effects than the Pdadmac. In addition, drainage speed was also much higher by the HCS treatments although paper formation was worsened. All the phenomena showed that the HCS can fix more dissolved and colloidal substances to cellulose fibers, indicating that the HCS functioned mainly with flocculation and even hydrogen bonding mechanisms. Data on optical properties further indicated that the HCS interacted preferentially with colloidal substances, since it fixed more 'dirty' microstickes to fibers which decreased more sheet brightness while increasing more sheet opacity (with both higher light absorption and scattering coefficients). Interestingly, the organic fixing agents did not decrease tensile, tearing, and folding strengths of paper sheets made from 100% recycled newsprint pulp, except when they were dosed in high amounts. On the contrary, the inorganic PAC had more serious negative effects on the strength properties, especially on folding endurance. The study suggested that proper use of the HCS can lead to better microstickies control effects than traditional agents and methods.

• 한국세라믹학회지
• /
• 제46권6호
• /
• pp.583-586
• /
• 2009

The Tantalum nitride has attracted wide at attention as issues related to the toxicity of Cd-related materials. But in the titration process of Ta$Cl_5$ solution with $NH_4$OH, $NH_4$Cl, as a by product, was remained in the prepared Tantalum precursor. The tantalum precursor with $NH_4$Cl was nitrided by ammonolysis. The red color tone of $Ta_3N_5$ was reduced by the residual $NH_4$Cl reduce. Therefore, amorphous Tantalum precursor was prepared by filtering process with as hydrous ethanol to remove the $NH_4$Cl. In the case of using Tantalum precursor without $NH_4$Cl, we successfully synthesized the Tantalum nitride with good red color. The value of red color tone was improved from $a^*$=36.8 to $a^*$=53.0. The synthesized powder was characterized by XRD, SEM, the Nitrogen / Oxygen Determinator, TG-DTA, and the CIE $L^*a^*b^*$ colorimeter.

• 한국환경보건학회지
• /
• 제20권1호
• /
• pp.54-61
• /
• 1994

This study was carried out to investigate the degree of contamination in private-drinking water supply (PDWS) and simple-piped water supply (SPWS), and to compare of water quality between them for 3 years from 1990 to 1992. The results of the study were as follows: 1. Private-drinking water supply (PDWS) (1) Field-Site (ㄱ) The items which were very significantly over the criteria (p<0.01), were temp., pH, NO-N, standard plate count (S.P.C.) and Coliform. (ㄴ) No. of households which were over the criteria, were 11.2~51.7% in temp., pH, NH$_3$-N and NO$_2$-N, and 83.1~93.3% in NO-N, S.P.C. and Coliform. (2) Moutain-Site (ㄱ) The items which were over the criteria, were NO$_2$-N (p<0.05), S.P.C. (p<0.01) and Coliform (p<0.01). (ㄴ) No. of households which were over the criteria, were 33.6 ~ 75.6% in NO$_2$-N, S.P.C. and Coliform. (3) No. of households which were fit to the criteria of all items, were 9.0% in field-site and 14.1% in mountain-site. 2. Simple-piped water supply (SPWS) (1) The items which were very significantly over the critera (p<0.01), were standard plate count (S.P.C.) and Coliform. (2) The water qualities of adjacent and remote samples were better than those of source samples. (3) Residual chloride was not detected in any sample. In conclusion, rural community requires to be continually performed the policy of safety drinking water supply, and to be devised an epoch-making counterplan for the level-up of simple-piped water supply (SPWS), espically on the method of disinfection.