• Journal of Environmental Impact Assessment
• /
• v.32 no.6
• /
• pp.419-430
• /
• 2023

In response to the periodic occurrence of cyanobacterial blooms in Korean freshwaters, various types of cyanobacteria removal technologies are being developed and implemented. Due to the differing principles behind these technologies, it is difficult to compare and evaluate their removal efficiencies. In this study, a standardized method for evaluating cyanobacteria removal efficiency was proposed by utilizing the results of removal operations using a mobile cyanobacteria removal device in the Seohwacheon area of Daechung Reservoir. During removal operations, the decrease in chlorophyll-a (chl-a) concentration (ΔChl-a) in the working area was calculated based on the amount of collected sludge, the efficiency rate, and the concentration of chl-a. Additionally, the required working days (WD) to reduce the chl-a concentration to 1 mg/m³ in the target area was calculated based on the area of the target zone, the maximum daily working area, and the efficiency rate. A method for calculating the cyanobacteria removal capacity was proposed based on the reduction rate of chl-a concentration in the water before and after the operation, the treatment capacity of the removal technology, and the water volume of the target area. The cyanobacteria removal capacity of the mobile cyanobacteria removal device used in this study was 6.64%/day (targeting the Seohwacheon area of Daechung Reservoir, approximately 500,000 m²), which was higher compared to other physical or physicochemical cyanobacteria removal technologies (0.02~4.72%/day). Utilizing the evaluation method of cyanobacteria removal efficiency presented in this study, it will be possible to compare and evaluate the cyanobacteria removal technologies currently being applied in Korea. This method could also be used to assess the performance and efficiency of physical or physicochemical combined cyanobacteria removal techniques in the "Guidelines for the Installation and Operation of Algae Removal Facilities and the Use of Algae Removal Agents" operated by the National Institute of Environmental Research.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.7 no.5
• /
• pp.316-322
• /
• 2002

A newly isolated heterotrophic marine bacterium, Vibrio alginolyticus, was used to remove a high load of ammonia gas under non-sterile condition. The cells were inoculated onto an inorganic packing material in a fixed-bed reactor (biofilter), and a high load of ammonia, in the range of ammonia gas concentration of 170 ppm to 880 ppm, was introduced continuously. Sucrose solution and 3% NaCl was supplied intermittently to supplement the carbon source and water to the biofilter. The average percentage of gas removed exceeded 85% for 107-day operation. The maximum removal capacity and the complete removal capacity were$19\;g-N\;kg^{-1}$ dry packing material $day^{-1}$ and $16\;g-N\;kg^{-1}$ dry packing material $day^{-1}$, respectively, which were about three times greater than those obtained in nitrifying sludge inoculated onto the same packing material. On day 82, the enhanced pressure drop was restored to the normal one by NaOH treatment, and efficient removal characteristics were later observed. During this operation, the non-sterile condition had no significantly adverse effect on the removability of ammonia by V. alginolyticus.

• Journal of Environmental Science International
• /
• v.23 no.9
• /
• pp.1583-1591
• /
• 2014

PVA-D2EHPA/TOPO beads containing two extractants, di-(2-ethylhexyl) phosphoric acid (D2EHPA) and trioctylphoshine oxide (TOPO) were prepared for the removal of copper ions from aqueous solution. The prepared PVA-D2EHPA/TOPO beads were characterized by SEM and FT-IR. The removal characteristics of copper ions by PVA-D2EHPA/TOPO beads was investigated using batch and continuous systems. In batch experiments, the maximum removal capacity calculated from Langmuir isotherm model was 18.6 mg/g and the optimal pH was in the range of 4.5~6. The continuous experiments showed that the removal capacity of copper ions increased with increasing inlet copper ion concentrations and bed heights, but decreased with increasing inlet flow rates.

• Journal of Korean Society for Atmospheric Environment
• /
• v.14 no.6
• /
• pp.599-606
• /
• 1998

Removal of toluene vapor from airstreams was studied in a biological reactor known as a biofilter. The biofilter was packed porous ceramic inoculated with thickened activated sludge (MLVSS 17,683 mg/L). The lab-scale biofilter was operated for 42 days under various experimental conditions including inlet toluene concentrations and flow rates of the contaminated air streams. Removal efficiency reached up 96.6% after 4 days from start up. Nutrient limitation was proposed as a reason for the decrease in biofilter performence. Biofilter performance decreased substantially, coincident with the buildup of back pressure due to accumulation of excess VSS within the medium bed. Practically, the bed needs to be backwashed when the overall pressure drop is greater than 460.6 Pa at SV (Space Velocity) 100 h-1. Periodic backwashing of the biofilter was necessary for removing excess biomass and attaining stable long -term high removal efficiency The removal efficiency of toluene in the biofilter decreased as the gas velocity and toluene concentration in the inlet gas increased. The maximum elimination capacity of ceramic biofilter could reach up to 444.85 g/m3. hr. When the loading of toluene exceed this critical value, substrate inhibition occurred.

• Journal of Korean Society on Water Environment
• /
• v.28 no.2
• /
• pp.277-284
• /
• 2012

This study developed a new ceramics in which natural zeolite was mixed and calcined with industrial by-product such as converter slag, red mud, and fly ash and evaluated the feasibility of the ceramics for removal of heavy metals in acid wastewater. The removal rate of heavy metal by ceramics increased in the order of ZS (zeolite and slag) > ZR (zeolite and red mud) > ZF (zeolite and fly ash) ceramics. The alkalinity increment and coherence of ceramics were increased in the order of ZS > ZR > ZF ceramics. The mixing ratio of natural zeolite to industrial by-product for maximum removal efficiency of heavy metal was 1:1 for ZS ceramics and 1:3 for ZR and ZF ceramics. The order of removal efficiency of heavy metal was observed to be ZS > ZR > ZF ceramics under the mixing ratio of 1:1 for ZS ceramics and 1:3 for ZR and ZF ceramics. The removal efficiency of heavy metal by ZS ceramics with 1:1 mixing ratio was Al 100%, Cd 54.6%, Cr 99.9%, Cu 98.7%, Fe 99.9%, Mn 42.2%, Ni 59.9%, Pb 99.8%, Zn 87.6%, respectively. In addition, the removal capacity of heavy metal by ZS ceramics was observed to be Al 2.01 mM/g, Cd 0.27 mM/g, Cr 1.02 mM/g, Cu 0.83 mM/g, Fe 0.95 mM/g, Mn 0.41 mM/g, Ni 0.55 mM/g, Pb 0.25 mM/g, Zn 0.70 mM/g, respectively. The comparative evaluation in the light of removal capacity, alkalinity increment, and coherence of ceramics showed the ZS ceramics had higher feasibility as a media than others for removal of heavy metals in acid wastewater.

• Korean Journal of Materials Research
• /
• v.31 no.6
• /
• pp.345-352
• /
• 2021

In this study, Ni nanoparticle supported by graphene oxide (GO) (Ni-GO) is successfully synthesized through hydrothermal synthesis and calcination, and Cr(VI) is extracted from aqueous solution. The morphology and structure of Ni-GO composites are characterized by scanning electron microscopy (SEM), trans mission electron microscopy (TEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). High-resolution transmission electron microscopy (HRTEM) and XRD confirms the high dispersion of Ni nanoparticle after support by GO. Loading Ni on GO can obviously enhance the stability of Ni-GO composites. It can be calculated from TGA that the mass percentage of Ni is about 60.67 %. The effects of initial pH and reaction time on Cr(VI) removal ability of Ni-GO are investigated. The results indicate that the removal efficiency of Cr(VI) is greater than that of bared GO. Ni-GO shows fast removal capacity for Cr(VI) (<25 min) with high removal efficiency. Dynamic experiments show that the removal process conforms to the quasi-second order model of adsorption, which indicates that the rate control step of the removal process is chemical adsorption. The removal capacity increases with the increase of temperature, indicating that the reaction of Cr(VI) on Ni-GO composites is endothermic and spontaneous. Combined with tests and characterization, the mechanism of Cr(VI) removal by rapidly adsorption on the surface of Ni-GO and reduction by Ni nanoparticle is investigated. The above results show that Ni-GO can be used as a potential remediation agent for Cr(VI)-contaminated groundwater.

• Journal of Sericultural and Entomological Science
• /
• v.42 no.2
• /
• pp.78-82
• /
• 2000

In this study, a comparative removal of chlorine from aqueous solutions of mulberry leaf powder(MLP) and activated carbon(AC) was investigated. The chlorine removal capacities of MLP and AC were shown as a function of contact time, pH and initial chlorine concentration. Optimum contact time and removal pH value of MLP were determined as 2 hr and pH 10, respectively. Chlorine removal increased with increasing initial chlorine concentration up to 1.3g/L. Both Langmuir and Freundlich adsorption models were suitable for describing the short-term removal of chlorine by MLP and AC. According to Freundlich adsorption isotherms, the maximum removal capacity of MLP(0.264 mg Cl$_2$/mg) was nearly two times greater than that of AC(0.56 mg Cl$_2$/mg). These results suggested that MLP might potentially be used as an alternative to traditional water treatment materials for removal of residual chlorine in drinking water or process wastewater.

• Journal of Environmental Science International
• /
• v.11 no.4
• /
• pp.361-366
• /
• 2002

Several effects on Pb$^{2+}$ removal by crab shell from aqueous solution were investigated. As the increase of initial Pb$^{2+}$ concentration and decrease of initial crab shell concentration, the time required to reach an equilibrium state and the residual Pb$^{2+}$ concentration increased. In our experimental ranges, the optimum initial Pb$^{2+}$ concentration and crab shell concentration were below 103 mg/$\ell$ and over 0.5 mg/$\ell$, respectively. Also, in order to investigate the mechanism of Pb$^{2+}$ removal by crab shell in aqueous solution, the crab shell was compared with chitosan and chitin on aspects of Pb$^{2+}$ removal capacity and Pb$^{2+}$ removal rate. The Pb$^{2+}$ removal by crab shell was greater than that by chitin and chitosan. The role of chitin was not so great in Pb$^{2+}$ removal by crab shell. The Pb$^{2+}$ removal by chitosan was not exactly correlated to the molecular weight of chitosan. weight of chitosan.

• The Korean Journal of Ecology
• /
• v.12 no.2
• /
• pp.75-82
• /
• 1989

Bacterial strains which have excellent removal capacity of phosphate or reduction capacity of were isolated from waste water. Among isolated strains. WR8 and WR1 strains were showed goood efficiency in removal of phosphate and reduction of respectively. When each strain was cultivated in waste water, WR8 strain removed about 85% of phosphate and WR1 strain reduced about 85% of -N. By the result of investigation of morphological and physiological characteristics, WR8 was identified as Aeromonas hydrophila and WR1 as Klebsiella pneumoniae.

• Journal of Korean Society on Water Environment
• /
• v.23 no.6
• /
• pp.966-972
• /
• 2007

A novel organoclay has been developed with aluminium-pillared clay modified with an amphoteric surfactant, N-Dodecyl-N,N-dimethyl-3-ammonio-1-propanesulfonate (DDAPS). This novel organoclay is expected to have phosphorus removal capacity as well as organic and inorganic contaminant removal capacity, due to aluminum inside the clay structure. It also exhibited less surfactant desorption than conventional cation surfactant-based organoclays. Phosphorus in water can be decreased from 0.2 mg/L to 0.0012 mg/L in 27 hours with this organoclay. Also, cadmium could removed from water using this proposed organo-clay. Experiments were performed under various pHs and amphoteric surfactants sorption capability was the highest at pH 5 when more of the amphoteric surfactant head group took on positive charges.