• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.892-897
• /
• 2000

In this study, tap wear was analyzed not only to predict the tap life time but also to propose an improved tap design. Because rake angle and thread relief of tap are the significant factors in geometry of tap, these two factors were picked as the experiment variables. The experiment was conducted with six types of tap which have 6$^{\circ}$ , 8$^{\circ}$ and 12$^{\circ}$ of rake angles with 0,08mm and 0.14 mm of thread relief. From the measured cutting force, it could be known that cutting torque was low at the large the rake thread relief and tool life was long as rake angle became large. Eventually, tool life is longest when rake angle is 12$^{\circ}$ and the with 0.08mm thread relief. Aand the width of crater wear and that of flank wear were measured when a tapping torque was 20 [$kg_f$-mm] . Most of the measured values were above the width of tool wear[$V_B$=O.O3m], which means that tool life is over.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
• /
• pp.685-690
• /
• 2000

In this study relationship between relief angles and chatter vibration in turning was examined by using the direct cutting test, in which the cutting depth of a tapered workpiece is varied continuously and the limiting depth of cut is measured at the time when chatter occurs. Test results reveal that 1) limiting depth of cut increases is proportion to side relief angles between 0$^{\circ}$ and 3$^{\circ}$, 2) limiting depth of cut does not show any evident change in spite of side relief angle increased from 3$^{\circ}$ to 12$^{\circ}$, 3) also limiting depth of cut does not change despite front angle change from 0$^{\circ}$ to 12$^{\circ}$.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 추계학술대회(한국공작기계학회)
• /
• pp.393-398
• /
• 2001

The technique of high speed machining is widely studied in machining fields, because the high efficiency and accuracy in machining can be obtained in high speed machining. Unfortunately the development of tool for high speed machining in not close behind that of machine tool. In this study, several types flat endmill is prepared for obtaining data according to tool shape. Especially, we concentrated in helix angle, number of cutting edge, rake angle and relief angle. Machinability is measured by cutting force, tool life, tool wear, chip shape and surface roughness according to cutting length. 3-axis cutting forces are acquired from the invented tool dynamometer for high speed machining. Particularly, we found out that the axial cutting force waveform has a good relation with tool wear features. By above results, it is suggested the endmill tool with $45^{\circ}$ helix angle, 6 cutting edge, $-15^{\circ}$ rake angle and $12^{\circ}$ relief angle be suitable for high speed machining

• 한국기계가공학회지
• /
• 제11권1호
• /
• pp.88-94
• /
• 2012

An axle drive shaft with double joint shaft, cross kit and yoke has an important role by transferring power and changing steering angle between axle and wheel in power train system. It has been used widely in the heavy machinery requiring a high reliability in the power train system. At fatigue failures of the axle drive shaft with the long span, a relatively high stress concentration at a snap ring groove on the drive shaft brings to significant fatigue damages under repeated loading condition. As Peterson's suggestions on this study, a relief groove in the vicinity of the snap ring groove is applied by decreasing the stress concentration and improving the fatigue life of axle drive shaft. By using FEM analysis, the decreasing effect of the stress concentration and extended fatigue life are due to the change of design parameters related with size and location of the relief groove. The relief groove with the design parameters such as d/b=2.0 and r/h=1.2 enables to decrease the stress concentration of 22.3% and increase the fatigue life more than 3 times by comparing with no relief groove application.

• 대한기계학회논문집A
• /
• 제21권9호
• /
• pp.1520-1530
• /
• 1997

Machining pressed compacts of ceramic and WC-Co materials can be the most cost effective way of forming the bodies prior to sintering when the required number of pieces is small. In this study, in order to clarify the machinability for turning, the $Si_3N_4$ and the WC-Co green compacts unsintered were machined under different cutting conditions with various tools. Absorbing chips by vacuum hose decreases tool wear. The tool wear becomes larger in the order of the ceramic, CBN and cemented carbide tools in machining the $Si_3N_4$ green compacts. In machining the WC-Co green compacts, the tool wear becomes larger in the order of the ceramic, cemented carbide and CBN tools. The land of cutting edge does not affect tool wear. When machining with cemented carbide tool, the tool wear i equal cutting length is nearly identical in spite of the increase of cutting spee, and the roughness of machined surface was the best in the cutting speed of 90 m/min. The tool wear decreases with the increase of rake angle and relief angle and with the decrease of nose radius. The machined surfaces become worse with the increase of feed rate and depth of cut, and with the decrease of rake angle and relief angle. The tool wear is not affected by the feed and depth of cut.

• 한국측량학회지
• /
• 제30권1호
• /
• pp.21-30
• /
• 2012

위성 카메라의 두 밴드가 다른 관측 각(Look angle)으로 촬영 시, 두 밴드간의 정합이 요구된다. 밴드 정합(Band registration)은 플랫폼의 다이나믹스(Dynamics)와 시차효과로 인하여 상수매개변수(constant parameter)로 수학적인 모델을 수립하여 정합(registration)을 수행하기 어렵다. 시차효과는 지표면 표고에 의해 야기되는 현상으로 이는 두 밴드간 정합 특성이 지표면의 표고의 함수로 주어진다. 두 밴드간 정합이 성공적으로 이뤄지기 위하여 시차효과를 보상하는 표고시차보상기법이 요구된다. 이러한 표고시차보상은 특히 고해상도 영상정합에서 중요하다. 표고시차보상기법은 하나의 밴드를 다른 관측 각을 가지는 다수의 CCD라인으로 구성한 경우에도 적용이 가능하다. 한 밴드에서 촬영된CCD라인 영상들은 연결된CCD라인마다 다른 관측 각을 가짐으로CCD라인간 표고시차가 발생하여 CCD라인간 지상거리 차가 표고에 따라 증가되는 왜곡 현상이 나타나기 때문이다. 이를 보상하기 위해 기준밴드 또는 기준 CCD라인과 대상밴드 또는 대상 CCD라인간 영상과 지상간의 관계를 다항식을 사용하여 수학적으로 모델 하는RFM을 사용하였다. 실험결과, 표고시차가 존재하는 영상에 대해서도 제안된 기법으로 밴드 정합이 성공적으로 수행되는 것을 확인하였다.

• 소성∙가공
• /
• 제8권1호
• /
• pp.14-21
• /
• 1999

Trapezoid cups and square ones have been deep-drawn to 45mm in depth. Displacements and strains have been analysed by FEM and experiment. Strains and effective strains in the corner flanges of trapezoid cups have been compared with those in square cups. The results have shown that because of shear strains on the corner flange, it is necessary to adopt effective strain for comparing strains, mean vale of effective strains in the corner flange with a corner angle of 72 degrees is narly equal to those with a corner angle of a right angle and mean value of effective strains with a corner angle of 102 degrees is smaller than those with a corner angle of a right angle.

• Journal of Yeungnam Medical Science
• /
• 제4권1호
• /
• pp.151-156
• /
• 1987

본 증례는 Angle씨(氏) 2급 2류 부정교합 환자로서 Bioprogressive Mechanism을 적용시켜 양호한 결과를 얻었기에 이에 보고하는 바이며 치료결과는 다음과 같다. 1) 주소인 상하악 전치부 crowding을 해소하였다. 2) 구치부 관계는 Angle씨(氏) classII에서 classI으로 개선되었다. 3) Overbite와 overjet를 기능적으로 해소시킴과 동시에 전치부 torque control에 의한 만족스러운 치축경사도로 개선시켰다.(Photo.5) 4) 치료기간은 1년 11개월이 소모되었다.

• 대한전자공학회논문지
• /
• 제24권5호
• /
• pp.868-873
• /
• 1987

Holographic diffraction gratings which are the core element of the optical instruments such as a spectrophotometer have been fabricated using the photoresist as a recording material. A 488nm line from an argon laser is used in making the gratings. Transmission type surface-relief phase grating and reflection type which is fabsricated by coating the aluminum on the transmission type with thickness 2000\ulcornerare fabricated, the spatical frequency of which are 1200 lines/mm. Diffraction efficiency, scattered light and wave-front aberratin are measured to test the performance of the developed gratings. A marimum diffraction efficiency is given when light is incident at the Bragg angle. Theoretical efficiency is about 80%, but measured efficiency of the transmission type and reflection type is 50% and 45%, respectively.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1998년도 추계종합학술대회 논문집
• /
• pp.947-950
• /
• 1998

Geological structures such as fault and fracture patterns provide important information about preliminary exploration of mineralized areas and geological characterization. We apply a filtering method taking the sun's azimuth angle into account to a shaded relief image derived from a digital elevation model (DEM), by which even linear edges extending parallel to the sun direction can be effectively extracted. Then, Generalized Hough tranform is applied to extract lineanments which correspond to fault and fracture patterns.