• The Journal of Engineering Geology
• /
• v.14 no.1
• /
• pp.61-69
• /
• 2004

Building stones are used mainly as a material for making decoration and sculpture, and consequently they must have predominant physical properties extensively. Among various physical properties, the coefficient of pore dominates the usefulness of building stones, so the plans were made for establishing the quality classification of building stones with respect to the nature of pore. For this study, bore-hole core samples according to the depth of the biotite granites and the granitic gneiss were applicated. From the related chart between porosity and absorption ratio, Mungyeong granitic gneiss($Gn_1$) shows the widest phase of distribution in the range of measurement values, and the values decrease in the order of Pocheon granite($Gr_2$) and Mungyeong granite($Gr_1$) in the range. The strength of each rock mass varies with the degree of alteration. Also in correlation between compressive strength and tensile strength, the range of measurement values decrease in the order of $Gn_1$, $Gr_2$and $Gr_1$. Porosity is adopted as a representative physical property for establishing the quality classification of building stones, and then relative evaluation was made with regard to various physical properties. From the related chart between porosity(n)-specific gravity(G), absorption ratio(Ab), compressive strength(${\sigma}_{c}$), tensile strength(${\sigma}_{t}$), shore hardness(Hs) and Young's modulus($E_{t}$), standard of each grade is established.

• The Journal of Engineering Geology
• /
• v.25 no.4
• /
• pp.499-510
• /
• 2015

Artificial accelerated weathering test evaluated rocks from near the circuit road of Ulleungdo island, approximately 120 km from east of the Korean Peninsula. The tests subjected rock specimens to conditions based on the climate of the island. The specimens (such as basaltic breccia, trachyte, volcanic breccia) were preliminarily classified using a TAS diagram (XRF data) and based on the constituent minerals (XRD data); they were further classified by weathering degree according to their absorption ratios. During the artificial accelerated weathering, the absorption ratio of most of the specimens increased, but the point-load strength did not decrease in most cases, except for the volcanic breccia. The greater initial absorption ratio of trachyte rock specimen in comparison with the other specimens led to a greater increase of its absorption ratio during the artificial accelerated weathering test. The volcanic breccia specimens showed the greatest increase of absorption ratio and the biggest reduction ratio of the point- load strength during the tests. These results could aid prediction of the weathering rate of rocks in Ulleungdo island subjected to weathering processes; trachyte which appears to accelerate with time, and volcanic breccia whose mechanical strength can largely decrease in a relative short period of time. Proper measures therefore appear necessary for the prevention of natural disaster such as rock fall and landslide around the circuit road.

• The Journal of Engineering Geology
• /
• v.27 no.2
• /
• pp.153-164
• /
• 2017

The geological factors for causing ground subsidence are very diverse. It can be affected by any geological or extrinsic influences, and even within the same geological factor, the soil depression impact factor can be determined by different physical properties. As a result of reviewing a large number of papers and case histories, it can be seen that there are seven categories of ground subsidence factors. The depth and thickness of the overburden can affect the subsidence depending on the existence of the cavity, whereas the depth and orientation of the boundary between soil and rock are dominant factors in the ground composed of soil and rock. In case of soil layers, more various influencing factors exist such as type of soil, shear strength, relative density and degree of compaction, dry unit weight, water content, and liquid limit. The type of rock, distance from the main fracture and RQD can be influential factors in the bedrock. When approaching from the hydrogeological point of view, the rainfall intensity, the distance and the depth from the main channel, the coefficient of permeability and fluctuation of ground water level can influence to ground subsidence. It is also possible that the ground subsidence can be affected by external factors such as the depth of excavation and distance from the earth retaining wall, groundwater treatment methods at excavation work, and existence of artificial facilities such as sewer pipes. It is estimated that to evaluate the ground subsidence factor during the construction of underground structures in urban areas will be essential. It is expected that ground subsidence factors examined in this study will contribute for the reliable evaluation of the ground subsidence risk.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.30 no.3
• /
• pp.103-113
• /
• 2018

Tide-surge characteristics of the West/South domestic coasts were analyzed with a tool of EST (empirical simulation technique). As a result, stations of Incheon, Gunsan, Mokpo and Busan are categorized as tide-dominant coasts, while Yeosu, Tongyoung and Busan are as surge-dominant coasts. In the tide-dominant coasts, extreme sea level of less than 50-yr frequency is formed without typhoon-surge, while only 10-yr extreme sea level is formed in the surge-dominant coasts. As the results of casual condition of extreme sea level formation considering the relative degree of surge on tide, the regional characteristics were detected also. Three methods for estimating the design tide level were compared. The AHHW method shows an unrealistic outcomes of the concern of over estimate design. Furthermore, the probability distribution function method has been concerned as causing missing data if a huge typhoon occurs in a neap tide or a low tide. To cope with these drawbacks, the applicability of the EST method is proved to be suitable especially in tide-dominant coasts.

• Journal of KIISE
• /
• v.42 no.5
• /
• pp.642-651
• /
• 2015

A vanishing point is a point where parallel lines converge, and they become evident when a camera's lenses are used to project 3D space onto a 2D image plane. Vanishing point detection is the use of the information contained within an image to detect the vanishing point, and can be utilized to infer the relative distance between certain points in the image or for understanding the geometry of a 3D scene. Since parallel lines generally exist for the artificial structures within images, line-detection-based vanishing point-detection techniques aim to find the point where the parallel lines of artificial structures converge. To detect parallel lines in an image, we detect edge pixels through edge detection and then find the lines by using the Hough transform. However, the various textures and noise in an image can hamper the line-detection process so that not all of the lines converging toward the vanishing point are obvious. To overcome this difficulty, it is necessary to assign a different weight to each line according to the degree of possibility that the line passes through the vanishing point. While previous research studies assigned equal weight or adopted a simple weighting calculation, in this paper, we are proposing a new method of assigning weights to lines after noticing that the lines that pass through vanishing points typically belong to artificial structures. Experimental results show that our proposed method reduces the vanishing point-estimation error rate by 65% when compared to existing methods.

• Restorative Dentistry and Endodontics
• /
• v.36 no.2
• /
• pp.132-138
• /
• 2011

Objectives: The purpose of this study was to evaluate curing degree of three dual-cure resin cements with the elapsed time in self-cure and dual-cure mode by means of the repeated measure of micro-hardness. Materials and Methods: Two dual-cure self-adhesive resin cements studied were Maxcem Elite (Kerr), Rely-X Unicem (3M ESPE) and one conventional dual-cure resin cement was Rely-X ARC resin cement (3M ESPE). Twenty specimens for each cements were made in Teflon mould and divided equally by self-cure and dual-cure mode and left in dark, $36^{\circ}C$, 100% relative humidity conditional-micro-hardness was measured at 10 min, 30 min, 1 hr, 3 hr, 6 hr, 12 hr and 24 hr after baseline. The results of micro-hardness value were statistically analyzed using independent samples t-test and one-way ANOVA with multiple comparisons using Scheffe's test. Results: The micro-hardness values were increased with time in every test groups. Dual-cure mode obtained higher micro-hardness value than self-cure mode except after one hour of Maxcem. Self-cured Rely-X Unicem showed lowest value and dual-cured Rely-X Unicem showed highest value in every measuring time. Conclusions: Sufficient light curing to dual-cure resin cements should provided for achieve maximum curing.

• Journal of Korean Society on Water Environment
• /
• v.34 no.4
• /
• pp.423-430
• /
• 2018

Insomuch as it is important to manage water quality, from the perspective of water management, it is essential to understand the effect of the weirs on water quality and phytoplankton dynamics in various regions. The purpose of this study is to investigate the characteristics of nitro-nutrients, as well as occurrences and succession patterns of phytoplankton, in the river sections of the two weirs in the Yeongsan River for the five years (from 2012 to 2016) after the weir construction. In respect to this data, the average water temperature measured at the representative point in the section of the Seungchon Weir ($17.1^{\circ}C$) was higher than that of the Juksan Weir ($16.6^{\circ}C$) by comparison. By way of an analysis of this data, it was found that the water quality variables such as, organic matter, nitrogen nutrients and phosphorus nutrients were improved gradually during the period, but the degree of the improvement differs as noted and measured between the weirs. Under the circumstances, it is especially noted that the $NH_3-N$ concentration was higher for the point of the Seungchon Weir (2.204 mg/L) than that of the Juksan Weir (1.157 mg/L). This indicates that effluent as seen from sewage treatment plants and hydrological feature near the densely population area, could be the main cause for the incidence of water pollution in the upstream section of the Seungchon Weir. Additionally, the phytoplankton analysis showed that a relative abundance of diatoms and green algae were 56.9 % and 25.8 % respectively. However, it is noted that the cyanobacteria was measured lower as 10.7 %. Also, in the study sites cell density and occurrence frequency of cyanobacteria were relatively lower than compared to the same measurements noted in other rivers.

• Economic and Environmental Geology
• /
• v.37 no.3
• /
• pp.335-345
• /
• 2004

Total and extractable contents of heavy metals were measured in sediment and seafood from Bukhang and Boggil-ri tidal flats along the Mokpo coastal area, south-western part of Korean peninsular in order to assess the degree of metal pollution, metal bioavailability and metal hioaccumulation. The metal concentrations, except Pb were found to be greater than the background concentrations of sediments indicating the progress of cumulative contamination by anthropogenic origin of metals. The order of extractable metal concentrations in sediments were Mn(32-53 mg/kg)＞Zn(14-42 mg/tg)＞Cu(2.5-17.0 mg/kg)＞Pb(2.4-6.8 mg/kg)＞Cd(0.5-0.7 mg/kg). However, the amount of metals associated with extractable fraction of sediments were significantly high in Bukhang relative to Boggil-ri. Significant bioaccumulation of all metals, except Pb were observed in seaweed and benthos. The order of bioaccumulation of metals were: in concentration; all biota commonly, Mn(129-374 mg/kg)＞Zn(19-106 mg/kg)＞Cu(6-87 mg/kg)＞Cd(4.6-7.6 mg/kg)＞Pb(0.2-3.7 mg/kg), in BCF; Enteromorpha, Cd＞Mn＞Cu＞Zn＞Pb, Ilyoplax deschampsi, Cu＞Cd＞Mn＞Zn＞Pb, Urechis unicinctus, Cd＞Zn＞Mn＞Cu＞Pb. Some metal concentrations of Enteromorpha, especially Cu, Zn, weakly Pb in bukhang, Mn, Cd in boggili-ri, were correlate well with concentrations in sediment, indicating relatively more contaminated by the anthropogenic origin of metals in each tidal flat. The results clearly indicate that the seafood of bukhang, even of Boggili-ri known as clean area, are contaminated with metals.

• Journal of Energy Engineering
• /
• v.15 no.4 s.48
• /
• pp.243-249
• /
• 2006

An experimental study on the refrigerant-side pressure drop of slit fin an tube heat exchanger has been carried out. A comparison was made between the predictions of previously proposed empirical correlations and experimental data for the pressure drop on design conditions of condenser in micro-fin tube for R22 and Rl34a. Experiments were carried out under the conditions of inlet refrigerant temperature of $60^{\circ}C$ and mass fluxes varying from $150\;to\;250\;kg/m^{2}s$ for R22 and Rl34a. The inlet air conditions are dry bulb temperature of $35^{\circ}C$, relative humidity of 40% and air velocity varying from 0.68 to 1.43 m/s. Experiments show that pressure drop for R134a was $22{\sim}22.6%$ higher than R22 for the degree of subcooling $5^{\circ}C$ For the mass fluxes of $200{\sim}250\;kg/m^{2}s$, the deviation between the experimental and predicted values for the pressure drop was less than ${\pm}20%$ for R22 and Rl34a.

• KIPS Transactions on Software and Data Engineering
• /
• v.1 no.2
• /
• pp.127-136
• /
• 2012

Many research of hand gesture recognition based on vision system have been conducted which enable user operate various electronic devices more easily. 3D position calculation and meaningful gesture classification from similar gestures should be executed to recognize hand gesture accurately. A simple and cost effective method of 3D position calculation and gesture spotting (a task to recognize meaningful gesture from other similar meaningless gestures) is described in this paper. 3D position is achieved by calculation of two cameras relative position through pan/tilt module and a marker regardless with the placed position. Fuzzy garbage model is proposed to provide a variable reference value to decide whether the user gesture is the command gesture or not. The reference is achieved from fuzzy command gesture model and fuzzy garbage model which returns the score that shows the degree of belonging to command gesture and garbage gesture respectively. Two-stage user adaptation is proposed that off-line (batch) adaptation for inter-personal difference and on-line (incremental) adaptation for intra-difference to enhance the performance. Experiment is conducted for 5 different users. The recognition rate of command (discriminate command gesture) is more than 95% when only one command like meaningless gesture exists and more than 85% when the command is mixed with many other similar gestures.