• 한국시뮬레이션학회논문지
• /
• 제24권3호
• /
• pp.69-75
• /
• 2015

본 연구에서는 복합굴절차의 강도 해석을 통한 구조적 안정성을 평가하고자 한다. 3D CAD 데이터, 사용 재질에 대한 물성값, 하중 조건 및 경계조건을 바탕으로, 범용 구조 해석 프로그램인 Nastran을 활용하여 복합굴절차에 대한 정적 구조 해석을 실시하였다. 하부 프레임(Sub frame, Out-trigger, Chassis frame)에 대한 구조해석을 수행하기 위해, 각 Out-trigger가 최대 하중을 받는 4가지 경우를 산정하였다. 이러한 해석된 결과를 통하여 국부적으로 강도가 부족한 위치를 특정지어, 보다 안전한 설계에 도움이 되도록 하였다.

• Computers and Concrete
• /
• 제20권6호
• /
• pp.671-682
• /
• 2017

In this research, seismic response of pipes is examined by applying nanotechnology and piezoelectric materials. For this purpose, a pipe is considered which is reinforced by carbon nanotubes (CNTs) and covered with a piezoelectric layer. The structure is subjected to the dynamic loads caused by earthquake and the governing equations of the system are derived using mathematical model via cylindrical shell element and Mindlin theory. Navier-Stokes equation is employed to calculate the force due to the fluid in the pipe. Mori-Tanaka approach is used to estimate the equivalent material properties of the nanocomposite and to consider the effect of the CNTs agglomeration on the scismic response of the structure. Moreover, the dynamic displacement of the structure is extracted using harmonic differential quadrature method (HDQM) and Newmark method. The main goal of this research is the analysis of the seismic response using piezoelectric layer and nanotechnology. The results indicate that reinforcing the pipeline by CNTs leads to a reduction in the displacement of the structure during an earthquake. Also the negative voltage applied to the piezoelectric layer reduces the dynamic displacement.

• Steel and Composite Structures
• /
• 제30권5호
• /
• pp.433-441
• /
• 2019

The aim of this research is reinforcing of concrete with variety of fiber reinforced polymer (FRP) configurations and investigates the load capacity and ductility of these connections using an experimental investigation. Six scaled-down RC exterior joints were tested under moderately monotonic loads. The results show that, the shape of the FRP had a different effect on the joint capacity and the connection ductility coefficient. The greatest effect on increasing the ductility factor was seen in the sample where two reinforcement plates were used on both sides of the beam web (RCS5 sample). For the sample with the presence of FRP plates at the top and bottom of the beam (RCS3 sample), the ductility factor was reduced even the load capacity of this sample increased. Except for the RCS3 sample, the rest of the samples exhibited an increase in the ductility factor due to the FRP reinforcement.

• Steel and Composite Structures
• /
• 제37권6호
• /
• pp.649-662
• /
• 2020

Although several types of rigid shear connectors have been developed particularly to increase load-carrying capacity, application is limited due to the complicated details of such connection. In this study, push-out tests were performed for specimens with hybrid shear connectors using headed studs and shear plates to identify the effects of each parameter on the structural performance of such shear connection. The test parameters included steel ratios of headed stud to shear plate, connection length, and embedded depth of shear plates. The peak strength and residual strength were estimated using various shear transfer mechanisms such as stud shear, concrete bearing, and shear friction. The hybrid shear connectors using shear plates and headed studs showed large load-carrying capacity and deformation capacity. The peak strength was predicted by the concrete bearing strength of the shear plates. The residual strength was sufficiently predicted by the stud shear strength of headed studs or by shear friction strength of dowel reinforcing bars. Further, the finite element analysis was performed to verify the shear transfer mechanism of the connection with hybrid shear connector.

• Advances in nano research
• /
• 제14권5호
• /
• pp.443-450
• /
• 2023

Carbon nanotubes (CNTs) have received increased interest in reinforcing research for polymer matrix composites due to their exceptional mechanical characteristics. Its high surface area/volume ratio and aspect ratio enable polymer-based composites to make the most of its features. This study focuses on the experimental tensile testing and fabrication of carbon nanotube reinforced composite (CNTRC) beams, exploring various micromechanical models. By examining the performance of these models alongside experimental results, the research aims to better understand and optimize the mechanical properties of CNTRC materials. Tensile properties of neat epoxy and 0.3%; 0.4% and 0.5% by CNT reinforced laminated single layer (0°/90°) carbon fiber composite beams were investigated. The composite plates were produced in accordance with ASTM D7264 standard. The tensile test was performed in order to see the mechanical properties of the composite beams. The results showed that the optimum amount of CNT was 0.3% based on the tensile capacity. The capacity was significantly reduced when 0.4% CNT was utilized. Moreover, the experimental results are compared with Finite Element Models using ABAQUS. Hashin Failure Criteria was utilized to predict the tensile capacity. Good conformance was observed between experimental and numerical models. More importantly is that Young' Moduli of the specimens is compared with the prediction Halpin-Tsai and Mixture-Rule. Although Halpin-Tsai can accurately predict the Young's Moduli of the specimens, the accuracy of Mixture-Rule was significantly low.

• 한국공간구조학회논문집
• /
• 제23권1호
• /
• pp.61-68
• /
• 2023

Buckling Restrained Braces can not only express the strength considered at the time of design, but also reduce the seismic load by energy dissipation according to the plastic behavior after yield deformation of the steel core. The physical characteristics and damping effect may be different according to the buckling prevention method of the steel core by the lateral restraint element. Accordingly, in this study, To compare hysteresis characteristics, Specimen(BRB-C) filled with mortar, specimen(BRB-R) combined with a buckling restraint ring and Specimen(BRB-EP) filled with engineering plastics was fabricated, and a cyclic loading test was performed. As a result of the cyclic loading test, the maximum compressive strength, cumulative energy dissipation and ductility of each test specimen was similar. But in case of the cumulative energy dissipation and ductility, BRB-C filled with the mortar specimen showed the lowest. This is considered to be because the gap between the steel core and the reinforcing material for plastic deformation was not uniformly formed by pouring mortar around the core part.

• 한국지반공학회논문집
• /
• 제33권3호
• /
• pp.29-36
• /
• 2017

NATM 공법에서 터널을 확대하거나 피난갱과 같이 좁은 단면에 록볼트를 설치하는 경우에는 록볼트를 경사지게 설치하거나 또는 짧은 볼트를 연결하여 시공할 수밖에 없다. 국내외에서 실시된 경사 록볼트에 대한 연구는 아직 미흡한 실정이며 실제 현장에 적용하기 위해서는 경사 록볼트의 거동특성에 대한 연구가 필요하다고 사료된다. 본 연구에서는 3차원 유한요소해석을 사용하여 경사 록볼트 시공 시 록볼트의 설치각도와 설치길이에 따른 최대 중립점 발생위치의 변화를 확인하고 이에 따른 록볼트에 의한 원지반 아치형성영역의 두께 변화를 비교 분석하여 지반보강효과에 대해 확인하였다. 해석결과 표준지보패턴(설치길이 4m)에선 설치각도가 감소할수록 터널 주변지반의 변형범위는 증가하여 지반보강효과가 감소하는 것을 알 수 있었다. 또한, 설치길이가 증가함에 따라 설치각도에 의한 영향을 적게 받은 것으로 나타났으며 설치각도 $45^{\circ}$ 이하에서는 설치길이의 영향을 받지 않는 것으로 나타났다. 이러한 결과로부터 경사록볼트의 설치각도는 $45^{\circ}$이상으로 하여 아칭영역을 확보하도록 하여야 하며, 설치각도 $75^{\circ}$이상인 경우 직각으로 설치하는 경우와의 보강효과의 차이가 크지 않음을 확인하였다. 또한 추가적인 상세 검토를 통하여 NATM 터널에서의 경사록볼트 설계지침을 제시하고자 하였다.

• 한국산학기술학회논문지
• /
• 제18권12호
• /
• pp.106-111
• /
• 2017

본 연구에서는 해양구조물의 상부(top side) 구조물을 설치할 때 필요한 장치인 LMU(Leg Mating Unit)의 강성을 구조해석을 통하여 검토하였다. 이것은 구조물의 지지 점에 장착되어 설치 시 충격을 흡수하고 안정적으로 구조물을 지지하는 데 사용된다. LMU는 가운데가 비어있는 원통형 구조로서 수직 하중을 지지하기 위해서 일래스토머릭 베어링(Elastomeric Bearing, 이하 EB)과 철판을 여러 층으로 적층한다. EB의 강성은 기본적으로 베어링의 크기에 영향을 받지만, 동일한 크기에서도 내부 보강판의 적층 수에 따라 강성이 변하게 된다. 일반적으로 보강판과 압축 강성 사이의 관계를 분석하여 적합한 설계를 한다. EB의 강성은 변위를 제어하면서 반력을 산출하는 방식으로 분석을 한다. 먼저 보강판의 크기와 압축 강성 관계를 검토하고, 보강판의 적층 수와 압축 강성 관계를 검토한다. LMU는 장착되는 지점마다 다른 하중이 요구된다. 해석을 통해 각 지점에서 동일한 변형이 발생하도록 압축 강성을 다르게 설계하는 것이 목표이다. 본 연구의 유한요소해석을 위하여 상용 프로그램인 ANSYS를 이용하였다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제22권4호
• /
• pp.10-18
• /
• 2018

본 연구는 시멘트 모르타르속에 매입된 철근주위가 건조될 때 불안정한 전류분포의 영향을 측정하고, 교류 임피던스 특성변화에 대한 영향을 고찰하는 것을 목적으로 한다. 건조과정중 철근의 전기화학적 반응을 측정하기 위해, 두 개의 철근이 매입된 3개의 시멘트 모르타르가 실험을 위해 준비되었다. 주요 변수는 20mm 모르타르 두께를 동일하게 가지도록 하여, 두 철근사이의 간격이 10, 20과 30mm가 되도록 하였다. 해양환경에서 콘크리트 구조물속의 철근 부식속도를 가정하기 위해서, 3개의 모르타르 시험체는 15 사이클의 침지-건조환경(해수에서 24시간 침지와 48시간 실온 건조)에 노출되었다. 부식전위의 변화는 건조중에 용존산소의 확산속도 증가로 인해 귀한 방향으로 이동하는 것이 관찰되었다. 침지-건조환경에서 교류 임피던스는 100kHz에서 1mHz까지 측정되었다. 철근과 모르타르사이의 계면상태를 설명하기 위해 이론적 모델이 제안되었으며, 그것은 용액저항, 전하이동저항과 CPE로 구성된 등가회로를 사용하였다. 철근의 부식이 진행됨에 따라, 저주파수 영역에서 확산 임피던스가 나타났다. 침지-건조 환경중 건조과정에서 이송차가 $45^{\circ}$에 가까워지는 현상으로써 전류분포가 불균일해지는 경향을 보였다.

• Structural Engineering and Mechanics
• /
• 제90권6호
• /
• pp.611-633
• /
• 2024

This study intends to investigate the response of multi-cell (MC) beams to flexural loads in which the primary reinforcement is composed of both metallic and non-metallic materials. "Multi-cell" describes beam sections with multiple longitudinal voids separated by thin webs. Seven reinforced concrete MC beams measuring 300×200×1800 mm were tested under flexural loadings until failure. Two series of beams are formed, depending on the type of main reinforcement that is being used. A control RC beam with no openings and six MC beams are found in these two series. Series one and two are reinforced with metallic and non-metallic main reinforcement, respectively, in order to maintain a constant reinforcement ratio. The first crack, ultimate load, deflection, ductility index, energy absorption, strain characteristics, crack pattern, and failure mode were among the structural parameters of the beams under investigation that were documented. The primary variables that vary are the kind of reinforcing materials that are utilized, as well as the kind and quantity of mesh layers. The outcomes of this study that looked at the experimental and numerical performance of ferrocement reinforced concrete MC beams are presented in this article. Nonlinear finite element analysis (NLFEA) was performed with ANSYS-16.0 software to demonstrate the behavior of composite MC beams with holes. A parametric study is also carried out to investigate the factors, such as opening size, that can most strongly affect the mechanical behavior of the suggested model. The experimental and numerical results obtained demonstrate that the FE simulations generated an acceptable degree of experimental value estimation. It's also important to demonstrate that, when compared to the control beam, the MC beam reinforced with geogrid mesh (MCGB) decreases its strength capacity by a maximum of 73.33%. In contrast, the minimum strength reduction value of 16.71% is observed in the MC beams reinforced with carbon reinforcing bars (MCCR). The findings of the experiments on MC beams with openings demonstrate that the presence of openings has a significant impact on the behavior of the beams, as there is a decrease in both the ultimate load and maximum deflection.