Steel and Composite Structures

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

An experimental study on the effect of CFRP on behavior of reinforce concrete beam column connections

  • Xie, Qiang (School of Civil Engineering, Central South University) ;
  • Sinaei, Hamid (Department of Civil Engineering, Sirjan Branch, Islamic Azad University) ;
  • Shariati, Mahdi (Faculty of Civil Engineering, University of Tabriz) ;
  • Khorami, Majid (Universidad UTE, Facultad de Arquitectura y Urbanismo, Calle Rumipamba s/n y Bourgeois) ;
  • Mohamad, Edy Tonnizam (Centre of Tropical Geoengineering (GEOTROPIK), Faculty of Civil Engineering, Universiti Teknologi Malaysia) ;
  • Bui, Dieu Tien (Institute of Research and Development, Duy Tan University)
  • Received : 2018.09.08
  • Accepted : 2019.03.03
  • Published : 2019.03.10
⟨ Previous Next ⟩

Abstract

The aim of this research is reinforcing of concrete with variety of fiber reinforced polymer (FRP) configurations and investigates the load capacity and ductility of these connections using an experimental investigation. Six scaled-down RC exterior joints were tested under moderately monotonic loads. The results show that, the shape of the FRP had a different effect on the joint capacity and the connection ductility coefficient. The greatest effect on increasing the ductility factor was seen in the sample where two reinforcement plates were used on both sides of the beam web (RCS5 sample). For the sample with the presence of FRP plates at the top and bottom of the beam (RCS3 sample), the ductility factor was reduced even the load capacity of this sample increased. Except for the RCS3 sample, the rest of the samples exhibited an increase in the ductility factor due to the FRP reinforcement.

Keywords

References

  1. Ardalan, H., Eslami, A. and Nariman-Zadeh, N. (2009), "Piles shaft capacity from CPT and CPTu data by polynomial neural networks and genetic algorithms", Comput. Geotech., 36(4), 616-625. https://doi.org/10.1016/j.compgeo.2008.09.003
  2. Arabnejad, K.M.M., Ramli Sulong, N.R., Shariati, M. and Tahir, M.M. (2016), "Investigation of through beam connection to concrete filled circular steel tube (CFCST) column", J. Constr. Steel Res., 121, 144-162. https://doi.org/10.1016/j.jcsr.2016.01.002
  3. Aslam, M., Shafigh, P., Jumaat, M.Z. and Shah, S.N.R. (2015), "Strengthening of RC beams using prestressed fiber reinforced polymers-A review", Constr. Build. Mater., 82, 235-256. https://doi.org/10.1016/j.conbuildmat.2015.02.051
  4. Bazzaz, M., Andalib, Z., Kheyroddin, A. and Kafi, M.A. (2015), "Numerical comparison of the seismic performance of steel rings in off-centre bracing system and diagonal bracing system", Steel Compos. Struct., Int. J., 19(4), 917-937. https://doi.org/10.12989/scs.2015.19.4.917
  5. Bezerra, L.M., Barbosa, W.C., Bonilla, J. and Cavalcante, O.R. (2018), "Truss-type shear connector for composite steelconcrete beams", Constr. Build. Mater., 167, 757-767. https://doi.org/10.1016/j.conbuildmat.2018.01.183
  6. Daly, A. and Witarnawan, W. (1997), "Strengthening of bridges using external post-tensioning", Paper PA3307/97, Transportation Research Laboratory, Berkshire, UK.
  7. Engindeniz, M., Kahn, L.F. and Abdul-Hamid, Z. (2005), "Repair and strengthening of reinforced concrete beam-column joints: State of the art", ACI Struct. J., 102(2).
  8. Fanaie, N., Esfahani, F.G. and Soroushnia, S. (2015), "Analytical study of composite beams with different arrangements of channel shear connectors", Steel Compos. Struct., Int. J., 19(2), 485-501. https://doi.org/10.12989/scs.2015.19.2.485
  9. Hadi, M.N. and Tran, T.M. (2016), "Seismic rehabilitation of reinforced concrete beam-column joints by bonding with concrete covers and wrapping with FRP composites", Mater. Struct., 49(1-2), 467-485. https://doi.org/10.1617/s11527-014-0511-4
  10. Hosseinpour, E., Baharom, S., Badaruzzaman, W.H.W., Shariati, M. and Jalali, A. (2018), "Direct shear behavior of concrete filled hollow steel tube shear connector for slim-floor steel beams", Steel Compos. Struct., Int. J., 26(4), 485-499.
  11. Hui, Y. and Irawan, P. (2001), "Behaviour of full-scale lightly reinforced concrete beam-column joints", Civil Engineering Research; Nanyang Technological University, Singapore, pp. 44-45.
  12. Ismail, M., Shariati, M., Awal, A., Chiong, C., Chahnasir, E., Porbar, A., Heydari, A. and Khorami, M. (2018), "Strengthening of bolted shear joints in industrialized ferrocement construction", Steel Compos. Struct., Int. J., 28(6), 681-690.
  13. Khorramian, K., Maleki, S., Shariati, M. and Ramli Sulong, N.R. (2015), "Behavior of Tilted Angle Shear Connectors", PLoS one, 10(12), 1-11.
  14. Khorramian, K., Maleki, S., Shariati, M., Jalali, A. and Tahir, M.M. (2017), "Numerical analysis of tilted angle shear connectors in steel-concrete composite systems", Steel Compos. Struct., Int. J., 23(1), 67-85. https://doi.org/10.12989/scs.2017.23.1.067
  15. Lee, H.-J. and Hwang, J.-S. (1999), "A study on the effect of fracture delay of intelligent FRP by transparent photoelastic experimental method", Transact. Kor. Soc. Mech. Eng. A, 23(11), 1904-1911. https://doi.org/10.22634/KSME-A.1999.23.11.1904
  16. McCormac, J.C. and Brown, R.H. (2015), Design of Reinforced Concrete, John Wiley & Sons.
  17. Mohammadhassani, M., Suhatril, M., Shariati, M. and Ghanbari, F. (2014), "Ductility and strength assessment of HSC beams with varying of tensile reinforcement ratios", Struct. Eng. Mech., Int. J., 48(6), 833-848.
  18. Nasrollahi, S., Maleki, S., Shariati, M., Marto, A. and Khorami, M. (2018), "Investigation of pipe shear connectors using push out test", Steel Compos. Struct., Int. J., 27(5), 537-543.
  19. Nordin, H. (2005), "Strengthening structures with externally prestressed tendons: literature review."
  20. Sadeghipour, E.S., Zandi, Y., Shariati, M., Dehghani, E., Toghroli, A., Mohamed, E.T., Shariati, A., Safa, M., Wakil, K. and Khorami, M. (2018), "Application of support vector machine with firefly algorithm for investigation of the factors affecting the shear strength of angle shear connectors", Smart Struct. Syst., Int. J., 22(4), 413-424.
  21. Safa, M., Shariati, M., Ibrahim, Z., Toghroli, A., Baharom, S.B., Nor, N.M. and Petkovic, D. (2016), "Potential of adaptive neuro fuzzy inference system for evaluating the factors affecting steelconcrete composite beam's shear strength", Steel Compos. Struct., Int. J., 21(3), 679-688. https://doi.org/10.12989/scs.2016.21.3.679
  22. Sedghi, Y., Zandi, Y., Toghroli, A., Safa, M., Mohamad, E.T., Khorami, M. and Wakil, K. (2018), "Application of ANFIS technique on performance of C and L shaped angle shear connectors", Smart Struct. Syst., Int. J., 22(3), 335-340.
  23. Shahabi, S.E.M., Ramli Sulong, N.H., Shariati, M., Mohammadhassani, M. and Shah, S.N.R. (2016a), "Numerical analysis of channel connectors under fire and a comparison of performance with different types of shear connectors subjected to fire", Steel Compos. Struct., Int. J., 20(3), 651-669. https://doi.org/10.12989/scs.2016.20.3.651
  24. Shahabi, S., Sulong, N., Shariati, M. and Shah, S. (2016b), "Performance of shear connectors at elevated temperatures-A review", Steel Compos. Struct., Int. J., 20(1), 185-203. https://doi.org/10.12989/scs.2016.20.1.185
  25. Shariati, M. (2013), "Behaviour of C-shaped Shear Connectors in Stell Concrete Composite Beams", Jabatan Kejuruteraan Awam, Fakulti Kejuruteraan, Universiti Malaya.
  26. Shariati, M., Ramli Sulong, N.H., Sinaei, H., Arabnejad, K.M.M., Mehdi, M. and Shafigh, P. (2011), "Behavior of Channel Shear Connectors in Normal and Light Weight Aggregate Concrete (Experimental and Analytical Study)", Adv. Mater. Res., 168, 2303-2307. https://doi.org/10.4028/www.scientific.net/AMR.168-170.2303
  27. Shariati, A., Ramli Sulong, N.R., Suhatril, M. and Shariati, M. (2012a), "Investigation of channel shear connectors for composite concrete and steel T-beam", Int. J. Phys. Sci., 7(11), 1828-1831.
  28. Shariati, M., Ramli Sulong, N., Suhatril, M., Shariati, A., Arabnejad Khanouki, M. and Sinaei, H. (2012b), "Fatigue energy dissipation and failure analysis of channel shear connector embedded in the lightweight aggregate concrete in composite bridge girders", Proceedings of the 5th International Conference on Engineering Failure Analysis, The Hague, The Netherlands, July.
  29. Shariati, M., Ramli Sulong, N.R., Suhatril, M., Shariati, A., Khanouki, M.A. and Sinaei, H. (2012c), "Behaviour of Cshaped angle shear connectors under monotonic and fully reversed cyclic loading: An experimental study", Mater. Des., 41, 67-73. https://doi.org/10.1016/j.matdes.2012.04.039
  30. Shariati, M., Shariati, A., Ramli Sulong, N.R., Suhatril, M. and Arabnejad, K.M.M. (2014), "Fatigue energy dissipation and failure analysis of angle shear connectors embedded in high strength concrete", Eng. Fail. Anal., 41, 124-134. https://doi.org/10.1016/j.engfailanal.2014.02.017
  31. Shariati, M., Ramli Sulong, N.R., Shariati, A. and Arabnejad, K.M.M. (2015), "Behavior of V-shaped angle shear connectors: experimental and parametric study", Mater. Struct., 49(9), 3909-3926.
  32. Shariati, M., Ramli Sulong, N.R., Shariati, A. and Kueh, A.B.H. (2016), "Comparative performance of channel and angle shear connectors in high strength concrete composites: An experimental study", Constr. Build. Mater., 120, 382-392. https://doi.org/10.1016/j.conbuildmat.2016.05.102
  33. Shariati, M., Toghroli, A., Jalali A. and Ibrahim, Z. (2017), "Assessment of stiffened angle shear connector under monotonic and fully reversed cyclic loading", Proceedings of the 5th International Conference on Advances in Civil, Structural and Mechanical Engineering - CSM 2017, Zurich, Switzerland.
  34. Tahmasbi, F., Maleki, S., Shariati, M., Ramli Sulong, N.R. and Tahir, M.M. (2016), "Shear capacity of C-shaped and L-shaped angle shear connectors", PloS one, 11(8), e0156989. https://doi.org/10.1371/journal.pone.0156989
  35. Tang, W.C., Balendran, R.V., Nadeem, A. and Leung, H.Y., (2006), "Flexural strengthening of reinforced lightweight polystyrene aggregate concrete beams with near-surface mounted GFRP bars", Build. Environ., 41(10), 1381-1393. https://doi.org/10.1016/j.buildenv.2005.05.029
  36. Thomas, P. and Priestley, M. (1992), Seismic Design of Reinforced Concrete and Masonry Buildings, New York Wiley-Interscience, USA.
  37. Wang, M., Shi, X., Zhou, J. and Qiu, X. (2018), "Multi-planar detection optimization algorithm for the interval charging structure of large-diameter longhole blasting design based on rock fragmentation aspects", Eng. Optimiz., 50(12), 2177-2191. https://doi.org/10.1080/0305215X.2018.1439943
  38. Wang, M., Shi, X. and Zhou, J. (2019), "Optimal Charge Scheme Calculation for Multiring Blasting Using Modified Harries Mathematical Model", J. Perform. Constr. Facil., 33(2), 04019002. https://doi.org/10.1061/(ASCE)CF.1943-5509.0001263
  39. Wei, X., Shariati, M., Zandi, Y., Pei, S., Jin, Z., Gharachurlu, S., Abdullahi, M.M., Tahir, M.M. and Khorami, M. (2018), "Distribution of shear force in perforated shear connectors", Steel Compos. Struct., Int. J., 27(3), 389-399.
  40. Zhou, J., Li, E., Wang, M., Chen, X., Shi, X. and Jiang, L. (2019), "Feasibility of Stochastic Gradient Boosting Approach for Evaluating Seismic Liquefaction Potential Based on SPT and CPT Case Histories", J. Perform. Constr. Facil., 33(3), 04019024. https://doi.org/10.1061/(ASCE)CF.1943-5509.0001292

Cited by

  1. Identification of the most influencing parameters on the properties of corroded concrete beams using an Adaptive Neuro-Fuzzy Inference System (ANFIS) vol.34, pp.1, 2019, https://doi.org/10.12989/scs.2020.34.1.155
  2. Experimental study on axial compressive behavior of welded built-up CFT stub columns made by cold-formed sections with different welding lines vol.34, pp.3, 2019, https://doi.org/10.12989/scs.2020.34.3.347
  3. Numerical study on the axial compressive behavior of built-up CFT columns considering different welding lines vol.34, pp.3, 2019, https://doi.org/10.12989/scs.2020.34.3.377
  4. Computational estimation of the earthquake response for fibre reinforced concrete rectangular columns vol.34, pp.5, 2019, https://doi.org/10.12989/scs.2020.34.5.743
  5. Stress-strain model of weak PVC-FRP confined concrete column and strong RC ring beam joint under eccentric compression vol.35, pp.1, 2020, https://doi.org/10.12989/scs.2020.35.1.013
  6. Elevated temperature resistance of concrete columns with axial loading vol.9, pp.4, 2019, https://doi.org/10.12989/acc.2020.9.4.355
  7. Computational analysis of three dimensional steel frame structures through different stiffening members vol.35, pp.2, 2019, https://doi.org/10.12989/scs.2020.35.2.187
  8. Effect of progressive shear punch of a foundation on a reinforced concrete building behavior vol.35, pp.2, 2019, https://doi.org/10.12989/scs.2020.35.2.279
  9. Utilization of Support Vector Models and Gene Expression Programming for Soil Strength Modeling vol.45, pp.5, 2019, https://doi.org/10.1007/s13369-020-04441-6
  10. Influences of Mo Fibers on Mechanical Properties of Resin Mineral Composites vol.35, pp.4, 2020, https://doi.org/10.1007/s11595-020-2315-4
  11. Influence of porosity and cement grade on concrete mechanical properties vol.10, pp.5, 2019, https://doi.org/10.12989/acc.2020.10.5.393
  12. Optimized AI controller for reinforced concrete frame structures under earthquake excitation vol.11, pp.1, 2021, https://doi.org/10.12989/acc.2021.11.1.001
  13. An analytical model for PVC-FRP confined reinforced concrete columns under low cyclic loading vol.77, pp.2, 2021, https://doi.org/10.12989/sem.2021.77.2.179
  14. Forced Vibration Analysis of Composite Beams Reinforced by Carbon Nanotubes vol.11, pp.3, 2019, https://doi.org/10.3390/nano11030571
  15. Smart estimation of automatic approach in enhancing the road safety under AASHTO Standard specification and STM vol.79, pp.3, 2021, https://doi.org/10.12989/sem.2021.79.3.389
  16. Application of multi-hybrid metaheuristic algorithm on prediction of split-tensile strength of shear connectors vol.28, pp.2, 2019, https://doi.org/10.12989/sss.2021.28.2.167
  17. Analyzing shear strength of steel-concrete composite beam with angle connectors at elevated temperature using finite element method vol.40, pp.6, 2019, https://doi.org/10.12989/scs.2021.40.6.853
  18. Bilinear elasto-dynamical response of SDOF system under sinusoidal loading vol.7, pp.1, 2022, https://doi.org/10.1007/s41062-021-00640-8