• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.120-123
• /
• 2004

The bending phenomenon has been known to be occurred by the difference of velocity at the die exit. The difference of velocity at the die exit section can be obtained by the different velocity of billets inside die chamber after passing the multi-hole container. The curvature can be controlled by the two variables, the one of them is the different velocity of billets through the multi-hole container, the other is the difference of hole diameter. The bending phenomenon during extruding using four billets can be obtained by the difference of hole diameters in the multi-hole container or by the difference of relative velocity of billet inserted in the container. As results of DEFORM-3D analysis, it can be shown that bending can be obtained during extruding by the difference of relative velocity of two billets or by the difference of hole diameter, and the amount of curvature is increased by the difference of velocity and diameter. According to the shape of products, the curvature of rectangular section is bigger than the curvature of regular square section. And, it is estimated that, because the stress on the welding line is much higher than yield stress of material, the bonding of four billets can be obtained.

• Journal of Veterinary Clinics
• /
• v.27 no.4
• /
• pp.457-461
• /
• 2010

Three dogs were presented with signs of recurrence of coughing, dyspnea and difficulty of barking after endotracheal stent placement. On the basis of history taking, physical examination, laboratory tests and radiography, complications of endotracheal stent were suspected. Dog 1 had unfitted stent diameter (stent diameter is larger than tracheal diameter) and getting disentangled of proximal tracheal stent wire. Dog 2 was suspected a foreign body reaction. Dog 3 had the migration of stent caudally. Based on these cases, the veterinarian should accurately evaluate the indicated patients before endotracheal stent and has to select the appropriate stent (diameter, length and location) to prevent complications after endotracheal stent and concern the regular follow-ups to assure proper endotracheal stent placement.

• Textile Coloration and Finishing
• /
• v.16 no.4
• /
• pp.1-9
• /
• 2004

In recent, development of nano fiber has been one of the most active subjects in the world. Nano fiber is defined as a ultra fine yarn with a diameter unit of $10-100\times10^{-9}meter$, which is possible to be produced by an electro-spinning technology. In this study, physical characteristics and dyeing properties of nylon 66 nano fiber were investigated. Nylon 66 nano fiber was dyed with levelling type acid dyes. X-ray diffraction method and DSC analysis were used for the measurement of the degree of crystallization. Analysis of amino end groups was also performed in order to examine a relationship between number of amino groups and its dyeing property as well as water absorption behavior. The maximum exhaustion % of dyes and dyeing rate under various dyeing conditions, such as dyeing temperature and pH in dye bath, along with build-up properties for 2 acid dyes were evaluated. It was found that the degree of crystallization of nano fiber was smaller than that of regular fiber, and amino end groups of nano fiber were less than regular fiber. Half dyeing time of nano fiber was shorter than regular fiber because of the bigger specific surface area. Effect of pH on exhaustion % was small in case of nano fiber. Exhaustion of nano fiber increased with higher concentration of dye.

• Journal of the Korean Mathematical Society
• /
• v.45 no.6
• /
• pp.1647-1659
• /
• 2008

Let R be a ring with identity, X the set of all nonzero, nonunits of R and G the group of all units of R. First, we investigate some connected conditions of the zero-divisor graph $\Gamma(R)$ of a noncommutative ring R as follows: (1) if $\Gamma(R)$ has no sources and no sinks, then $\Gamma(R)$ is connected and diameter of $\Gamma(R)$, denoted by diam($\Gamma(R)$) (resp. girth of $\Gamma(R)$, denoted by g($\Gamma(R)$)) is equal to or less than 3; (2) if X is a union of finite number of orbits under the left (resp. right) regular action on X by G, then $\Gamma(R)$ is connected and diam($\Gamma(R)$) (resp. g($\Gamma(R)$)) is equal to or less than 3, in addition, if R is local, then there is a vertex of $\Gamma(R)$ which is adjacent to every other vertices in $\Gamma(R)$; (3) if R is unit-regular, then $\Gamma(R)$ is connected and diam($\Gamma(R)$) (resp. g($\Gamma(R)$)) is equal to or less than 3. Next, we investigate the graph automorphisms group of $\Gamma(Mat_2(\mathbb{Z}_p))$ where $Mat_2(\mathbb{Z}_p)$ is the ring of 2 by 2 matrices over the galois field $\mathbb{Z}_p$ (p is any prime).

• International Journal of Ocean System Engineering
• /
• v.3 no.4
• /
• pp.188-208
• /
• 2013

The motion response of floating structures should be adequately low to permit the operation of rigid risers along with dry well heads. Though Spar platforms have low heave responses under lower sea state, could become unacceptable in near resonance region of wave periods. Hence the hydrodynamic response, heave in particular, must be examined to ensure that it is minimized. To reduce heave motions, external damping devices are introduced and one such effective damping device is heave plate. Addition of heave plate can provide additional viscous damping and additional added mass in the heave direction which influence the heave motion. The present study focuses on the influence of heave plate on the hydrodynamic responses of Classic Spar in regular waves. The experimental investigation has been carried out on a 1:100 scale model of Spar with single and double heave plates in regular waves. Numerical investigation has been carried out to derive the hydrodynamic responses using ANSYS AQWA. The experimental results were compared with those obtained from numerical simulation and found to be in good agreement. The influence of disk diameter ratio, wave steepness, pretension in the mooring line and relative spacing between the plates on the hydrodynamic responses of Spar are evaluated and presented.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.5
• /
• pp.2368-2373
• /
• 2012

In this research, finite element method was carried out to evaluate the defomation of pipe and surface displacement for backfill of underground ficility. Various conditions for analysis were employer, including two different pipes(PE and concrete pipe), two different excavation depth(60cm and 150cm) and width(1.5D and 2D), a regular sand backfill, and four different flowable backfills. The vertical deformation of 60 cm diameter for PE was measured three times more than that of 30 cm diameter. The measured deformations for regular backfill and four flowable backfills were 0.320mm, and 0.135mm to 0.155mm, respectively. It ratio was around 40%. In case of 30cm diameter of concrete pipe, the measured vertical defomation was around 0.004mm for all the backfill materials. In case of installation depth, the effect of flowable backfill for flexible pipe is better than for rigid pipe. There is little effect on the deformation of concrete pipe with regular sand backfill and flowable backfill.

• Journal of Environmental Science International
• /
• v.27 no.1
• /
• pp.27-38
• /
• 2018

This study was carried out in the Bukhan River in the summer of 2014 and 2015, to identify the relationship between geosmin and the morphological changes in Anabaena. Identification of Anabaena was conducted using morphological and molecular analyses. Anabaena in this study was similar to Anabaena circinalis, A. crass, and A. spiroides with regard to regular coils, vegetative cell, akinete shape, and size, hoever, it was distinguishabl from A. crass and A. spiroides because of its larger trichome coil size. Additionally, the sequences of phycocyanin (PC) gene from Anabaena showed a 99% genetic similarity with A. circinalis NIES-1647 strain. The coil diameter of trichome ranged from 106 to $899{\mu}m$, and the diameter and abundance showed an insignificant positive correlation (r=0.544, p<0.05). The result of relationship between the coil diameter and the cell number per 360-degree rotation was kept at $33.8{\pm}5.2$ cells per $100{\mu}m$ diameter despite variable diameter. The average geosmin concentrations in 2014 and 2015 were investigated to be 99 ng/L and 35 ng/L, respectively. A. circinalis cell density contributed considerably to the change in geosmin and was positively correlated with geosmin concentration (2014; r=0.599, p<0.01, 2015; r=0.559, p<0.01). Our results suggest that geosmin and coil diameter could be estimated with the help of cell density.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.527-530
• /
• 1997

An automated process planning system for cold forging of non-axisymmetric parts of comparatively simple shape was developed in this study. Programs for the system have been written with Visual LISP in the AutoCAD using a personal computer and are composed of four main modules such as input module, shape cognition and shape expression module, material diameter determination module and process planning module. The design rules and knowledges for th system are extracted from the plasticity theories. handbook, relevant reference and empirical knowledge of field experts. Generally, in forging, only front view is needed for expression of axisymmetric parts, but non-axisymmetric parts are needed both front view and plane. At the plane, this system cognizes the external shape of non-axisymmetric parts - number of sides of regular polygon and radius of a circle circumscribing the polygon of n sides. At the front view, the system perceives diameter of axisymmetric portions and hight of primitive geometries such as polygon, cylinder, cone, concave, convex, etc.

• International Journal of Precision Engineering and Manufacturing
• /
• v.6 no.4
• /
• pp.31-36
• /
• 2005

This paper describes a research work on the die design for the deep drawing & ironing(D. D. I) of high pressure gas cylinder. D. D. I die set is large-sized die used in horizontal press, which is usually composed of a drawing, and an ironing die. Design method of D. D. I die set is very different from that of conventional cold forging die set. Outer diameter of the die set is fixed because of press specification and that of the insert should be as small as possible for saving material cost. In this study, D. D. I die set has been designed to consider those characteristics, and the feasibility of the designed die has been verified by FE-analysis. In addition, the automated system of die design has been developed in AutoCAD R14 by formulating the applied methods to the regular rules.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2006.05a
• /
• pp.743-746
• /
• 2006

In this paper, we propose and analyze a new parallel computer topology, called the Fibonacci posterorder circulants. It connects ${\Large f}_x,\;n{\geq}2$ processing nodes, same the number of nodes used in a comparable Fibonacci cube. Yet its diameter is only ${\lfloor}\frac{n}{3}{\rfloor}$ almost one third that of the Fibonacci cube. Fibonacci cube is asymmetric, but it is a regular and symmetric static interconnection networks for large-scale, loosely coupled systems. It includes scalability and Fibonacci cube as a spanning subgraph.