• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.7
• /
• pp.623-631
• /
• 2000

Effects of the taper angle and the angular velocity of a pulse tube on the enthalpy flow loss associated with the steady mass streaming were analysis by two-dimensional analysis of a pulse tube with variable cross-section. It was shown that the steady mass flux can lead to a large steady second-order temperature. The enthalpy flow loss associated with the steady mass streaming increases as the angular velocity increases. For a pulse tube where the viscous penetration depth is far thinner than the inner radius, the enthalpy flow loss can be significantly reduced by tapering the pulse tube since both the steady mass flux and the steady second-order temperature decrease as the taper angle increase.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.1
• /
• pp.25-31
• /
• 2003

This paper addresses an oil supply enhancement device to resolve a shortage of oil supply or no oil supply at all encountered at low speed operation for a variable speed reciprocating compressor used for household refrigerators. The oil supply enhancement device comprises a moving cylinder attached to the lower end of crankshaft and two of fluid diodes, each one at the inlet and outlet of the cylinder. Up-and-down movement of the cylinder against the lower end of the crankshaft together with the functioning of the two fluid diodes produces net oil flow from oil reservoir to inside the crankshaft. The experiment on the test bench has shown that enough oil supply into the oil feeding hole cu be made by using this device even at low speed range. Some analytical study has also been carried out to under-stand its oil supply mechanism.

• Journal of Industrial Technology
• /
• v.34
• /
• pp.15-20
• /
• 2014

Recently, PMSMs(Permanent Magnet Synchronous Motors) have become increasingly popular in various high-performance motor drive applications. However, the high-performance drive of PMSMs needs a position sensor such as a resolver, which increases not only the price of the system but also reduces the system reliability. This paper is on the implementation of sensorless control of a SPMSM, which drives a fan for cooling in appliances. In this paper, the rotor position for high-performance drive of a SPMSM is derived from back electromotive force (EMF) information proportional to the rotor speed. Also, the initial rotor position information for start-up is estimated from a saturation phenomenon of inductance. The validity of the proposed sensorless drives was confirmed by the experiment on the SPMSM drive systems for cooling fans of refrigerators and laptop computers.

• Progress in Superconductivity and Cryogenics
• /
• v.6 no.2
• /
• pp.35-39
• /
• 2004

The split-type free displacer Stirling refrigerators have been widely used for the cooling of infrared sensors and HTS filters. The thermodynamic and electric performance of the Stirling refrigerator is depending on the design and operating parameters. In the Stirling refrigerator with a free displacer, the refrigeration power is a function of the pressure wave in the expansion space, dynamics of a displacer, driving frequency, and etc.. In this study, the analysis of the small Stirling refrigerator was performed to investigate the effects of design parameters on the cooling capacity. The results show the effects of charging pressure, driving frequency, cold end temperature, natural frequency of a displacer and volume of expansion space on the performance of the Stirling refrigerator.

• Journal of Mechanical Science and Technology
• /
• v.18 no.12
• /
• pp.2137-2147
• /
• 2004

The recycling cell formation problem means that disposal products are classified into recycling part families using group technology in their end-of-life phase. Disposal products have the uncertainties of product status by usage influences during product use phase, and recycling cells are formed design, process and usage attributes. In order to deal with the uncertainties, fuzzy set theory and fuzzy logic-based neural network model are applied to recycling cell formation problem for disposal products. Fuzzy C-mean algorithm and a heuristic approach based on fuzzy ART neural network is suggested. Especially, the modified Fuzzy ART neural network is shown that it has a good clustering results and gives an extension for systematically generating alternative solutions in the recycling cell formation problem. Disposal refrigerators are shown as examples.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.12
• /
• pp.98-103
• /
• 2019

With the increasing need for environmental protection, it is particularly important to improve the energy saving and reliability of refrigerators. Generally, the cold air flowing into the freezer compartment transits to the bottom of the refrigerating compartment, which can lead to uneven temperature distribution. This paper proposes two design solutions for improving the temperature distribution problem. Of these, the optimal refrigeration design was selected and tested using Computational Fluid Dynamics (CFD) modeling and simulation. The results showed improved uniformity of the temperature distribution inside the refrigerator, thus benefitting food storage while reducing energy consumption.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.321-324
• /
• 1998

A single phase induction motor (SPIM) rated in fractional horsepower is widely used in home and industrial equipment: washing machines, fans, refrigerators, etc. In this paper, authors present the experimental results of the SPIM under controlling of currents of main and auxiliary windings by using a one-chip micro stator(OMS). This new starting method is developed to replace the conventional starting device consisted with a mechanical switch and a capacitor. In mentioned method, the soft-starting of SPIM is simply implemented and higher efficiency is obtained in comparison with conventional condenser type SPIM.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.02a
• /
• pp.33-35
• /
• 2003

There are three types that geometrical arrangement of the pulse tube and regenerator - in line type, U type, and coaxial type. The most compact and convenient one practical applications is the coaxial type. It can replace Stirling cryocooler without any change to the Dewar or the connection to the cooled devices. To investigate effects of the inertance tube, we perform experiments with varying inertance tube inner diameter and length. The experimental results show that optimum inertance tube inner diameter and length are 1.3mm, 1900mm respectively.

• Journal of the Korean Home Economics Association
• /
• v.24 no.3
• /
• pp.129-141
• /
• 1986

The purpose of this study was to test both psychological and demographic variables and their relationship to the consumers design evaluation with reference to television sets and refrigerators. The survey questionnaire consisted of three distinct areas: 1) demographic information about the subjects, 2) their interest in design and need for design, 3) their evaluation of‘ideal’designs the subjects were 900 adults selected from middle and high economic level in Seoul. The major findings were the‘ideal’design of the subjects was affected by interest in design and the need for design. The need for design was related to either self-esteem or to esteem of others. Interest in design and need for self-esteem were affected by demographic variables but the need for esteem of others was not.

• Proceedings of the KIEE Conference
• /
• 2001.04a
• /
• pp.15-18
• /
• 2001

SMES consists of superconducting magnet, power converter and cryostat and HTS current lead. The prototype cryostat with HTS current leads and refrigerators was designed and manufactured for micro-SMES. HTS current lead with cryocooler was measured the temperature rise under dc current. The cryostat was evaluated the helium boil-off and mechanical stress during transfer and vibration test. These results will be applied to develope the micro-SMES system.