• Korean Journal of Optics and Photonics
• /
• v.31 no.6
• /
• pp.334-343
• /
• 2020

In this paper, a study of the design of a lighting optical system to form indirect light was conducted, to reduce the glare caused by the hot spot of the LED. In the case of using an LED for indoor lighting, glare is caused because of the high luminance and non-uniform luminance distribution. In particular, LED stands are located close to the user's eyes and are used for a long time, so research to reduce glare is essential. Therefore, in this paper an optical system structural study and the design of an LED stand for glare reduction were conducted. Afterward, the luminance analysis and comparison to an existing LED stand product confirmed that the reflective LED stand proposed in this paper had better performance in terms of glare.

• Korean Journal of Optics and Photonics
• /
• v.23 no.6
• /
• pp.264-268
• /
• 2012

In this paper, we propose a new method for broadcasting in a WDM-PON system which has the merits of a simple and cost effective structure. It can be constructed using only an ASE (Amplified Spontaneous Emission) light source and a PI-RSOA (Polarization Independent - Reflective Semiconductor Optical Amplifier). Error-free broadcast signal transmission over 30 Km for 24 channels at 1.25 Gb/s has been successfully demonstrated.

• Current Optics and Photonics
• /
• v.2 no.1
• /
• pp.27-33
• /
• 2018

We report the physical implementation of a tunable photonic microwave delay line filter based on injection locking of a single Fabry-Perot laser diode (FP-LD) to a reflective semiconductor optical amplifier (RSOA). The laser generates equally spaced multiple wavelengths and a single tapped-delay line can be obtained with a dispersive single mode fiber. The filter frequency response depends on the wavelength spacing and can be tuned by the temperature of the FP-LD varying lasing wavelength. For amplitude control of the wavelengths, we use gain saturation of the RSOA and the offset between the peak wavelengths of the FP-LD and the RSOA to decrease the amplitude difference in the wavelengths. From the temperature change of total $15^{\circ}C$, the filter, consisting of four flat wavelengths and two wavelengths with slightly lower amplitudes on both sides, has shown tunability of about 390 MHz.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.13 no.3
• /
• pp.1-14
• /
• 2011

A dress is commonly designed and worn as a work of art. It is developed through various ways to show the expression of our bodies with functional aspects. Light plays a role in everyday life functionally and aesthetically. We can use the light in many different ways in order to enhance the beauty of the designs. The purpose of this study is to suggest sensible designs with the active expression of light reflection. The designs are especially focused on utilizing light that shows the combination between natural human body's movement and reflection of the light. The use of reflective materials shows the character of movement when it exposes to light. The methods allow to amplify the aesthetic effects of the designs. Reflective materials were used in the resulting design to show the various effects of light by applying the movement which is artistic and aesthetic pleasing aspect for the clothing. The movement is accentuated when the wearer moves, or the air flows through the adding materials on the clothing. In addition, the beads attached to the end of the springs to show the movement of the light. The combination of the spring and the light movement resulted in a dazzling effect. I hope in the future, more studies will be conducted to further use of fiber optics and other innovative ways to use light in fashion.

• Korean Journal of Optics and Photonics
• /
• v.23 no.5
• /
• pp.227-232
• /
• 2012

A large-signal time-domain model is implemented to analyze an FG-LD (Fiber Grating Laser Diode) in which a reflective laser diode is hybrid-integrated with a fiber Bragg grating (FBG). When the length of the externally integrated resonator is 8 mm, in which the effective FBG length of 2.1 mm is included, a static frequency chirp of 0.44 GHz and a dynamic frequency chirp of 6.4 GHz are observed. In addition, it is also observed that the eye of the 10Gbps NRZ signal is well open. The FG-LD is expected to be a cost-effective solution for a 10Gbps-class single wavelength laser covering a span of 50 km range.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.124-124
• /
• 2010

Currently, extreme ultraviolet lithography (EUVL) is being investigated for next generation lithography. EUVL is one of competitive lithographic technologies for sub-22nm fabrication of nano-scale Si devices that can possibly replace the conventional photolithography used to make today's microcircuits. Among the core EUVL technologies, mask fabrication is of considerable importance due to the use of new reflective optics having a completely different configuration compared to those of conventional photolithography. Therefore, new materials and new mask fabrication process are required for high performance EUVL mask fabrication. This study investigated the etching properties of SnO2 (Tin Oxide) as a new absorber material for EUVL binary mask. The EUVL mask structure used for etching is SnO2 (absorber layer) / Ru (capping / etch stop layer) / Mo-Si multilayer (reflective layer) / Si (substrate). Since the Ru etch stop layer should not be etched, infinitely high selectivity of SnO2 layer to Ru ESL is required. To obtain infinitely high etch selectivity and very low LER (line edge roughness) values, etch parameters of gas flow ratio, top electrode power, dc self - bias voltage (Vdc), and etch time were varied in inductively coupled Cl2/Ar plasmas. For certain process window, infinitely high etch selectivity of SnO2 to Ru ESL could be obtained by optimizing the process parameters. Etch characteristics were measured by on scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) analyses. Detailed mechanisms for ultra-high etch selectivity will be discussed.

• Current Optics and Photonics
• /
• v.7 no.4
• /
• pp.435-442
• /
• 2023

These days, the size of a reflective telescope has been increasing for astronomical observation. An additional optical system usually assists a large ground telescope for image analysis or the compensation of air turbulence. To guide collimated light to the external optical system through a designated path, a coudé mirror is usually adopted. Including a collimator, a coudé mirror of a ground telescope is affected by gravity, depending on the telescope's pointing direction. The mirror surface is deformed by the weight of the mirror itself and its mount, which deteriorates the optical performance. In this research, we propose an optimization method for the coudé mirror assembly for a 1-m class ground telescope that minimizes the gravitational surface error (SFE). Here the mirror support positions and the sizes of the mount structure are optimized using finite element analysis and the response surface optimization method in both the horizontal and vertical directions, considering the telescope's altitude angle. Throughout the whole design process, the coefficients of the Zernike polynomials are calculated and their amplitude changes are monitored to determine the optimal design parameters. At the same time, the design budgets for the thermal SFE and the mass and size of the mount are reflected in the study.

• Korean Journal of Optics and Photonics
• /
• v.33 no.2
• /
• pp.74-83
• /
• 2022

The entire process, from the raw material to the final system qualification test, has been developed to fabricate a large-diameter, lightweight reflective-telescope system for a satellite observation. The telescope with 3 anastigmatic mirrors has an aperture of 700 mm and a total mass of 66 kg. We baked a silicon carbide substrate body from a carbon preform using a reaction sintering method, and tested the structural and chemical properties, surface conditions, and crystal structure of the body. We developed the polishing and coating methods considering the mechanical and chemical properties of the silicon carbide (SiC) body, and we utilized a chemical-vapor-deposition method to deposit a dense SiC thin film more than 170 ㎛ thick on the mirror's surface, to preserve a highly reflective surface with excellent optical performance. After we made the SiC mirrors, we measured the wave-front error for various optical fields by assembling and aligning three mirrors and support structures. We conducted major space-environment tests for the components and final assembly by temperature-cycling tests and vibration-shock tests, in accordance with the qualifications for the space and launch environment. We confirmed that the final telescope achieves all of the target performance criteria.

• Korean Journal of Optics and Photonics
• /
• v.20 no.4
• /
• pp.217-222
• /
• 2009

In this paper, a low-cost hybrid-integrated tunable laser is realized using a polymer-ring resonator-based add/drop filter reflector and a reflective semiconductor optical amplifier. The add/drop filter reflector, composed of a double-ring resonator with different radii, can have characteristics of selective wavelength reflection and wide wavelength tuning with an aid of vernier effect derived from the radii difference. By hybrid-integrating the reflective semiconductor optical amplifier with the add/drop filter reflector, a tunable laser can be realized through an active alignment method. The hybrid laser exhibited a single mode lasing with side mode suppression ratio of 26 dB and full width half maximum of 0.03 nm. In addition, applying a low current as small as 25 mA onto electrodes over add/drop filter reflector, a wavelength tuning range of 17 nm could be obtained.

• Advances in Energy Research
• /
• v.5 no.3
• /
• pp.227-237
• /
• 2017

The continuous increase of emission rates of green house gases and the effects on global warming added a new dimension to the problem of substituting the petroleum and its derivatives by environment friendly and sustainable energy sources for the world. Solar and wind energy appear at the top of the list of renewable of high potential, widely available, of dominated technology and well accepted. Brazil is one of the few countries in the world that receives number hours of sunshine exceeding 3,000 hours per year with a daily average of 4.5 to 6 kWh. However, this potential is largely unexplored and poorly tapped. The number of renewable systems implanted in Brazil has grown in recent years, but still insignificant when compared, for example, with Germany and Spain among others. This paper presents the results of an optical study on small concentration solar collector with evacuated tube enveloping the absorber and internal reflective surface fixed on the bottom part of the evacuated tube. The designed collector has a 2D geometrical concentration ratio between 2.455 and 4.91. The orientation of the solar collector, the ratio of the radius of the receiver to the radius of the absorber, the incidence angle for each period of the year, the collector inclination angle, the aperture angle of the reflective surface, concentration and optical efficiency were determined. The ray traces and flux distribution on the absorber of the evacuated tube solar collector were determined by using the program Ray Optics Simulation. The optical efficiency varies during the year according to the solar declination. For the periods were the solar declination is close to zero the efficiencies are maximum, and the variation during the day is around 25.88% and 99.9%. For the periods were the solar declination is maximum the efficiencies are minimum, and the variation during the day is around 23.78% and 91.79%.