• Journal of Astronomy and Space Sciences
• /
• 제28권4호
• /
• pp.345-354
• /
• 2011

Earth acquisition is to solve when earth can be visible from satellite after Sun acquisition during launch and early operation period or on-station satellite anomaly. In this paper, the algorithm and test result of the Communication, Ocean and Meteorological Satellite (COMS) Earth acquisition are presented in case of on-station satellite anomaly status. The algorithms for the calculation of Earth-pointing attitude control parameters including those attitude direction vector, rotation matrix, and maneuver time and duration are based on COMS configuration (Eurostar 3000 bus). The coordinate system uses the reference initial frame. The constraint calculating available time-slot to perform the earth acquisition considers eclipse, angular separation, solar local time, and infra-red earth sensor blinding conditions. The results of Electronics and Telecommunications Research Institute (ETRI) are compared with that of the Astrium software to validate the implemented ETRI software.

• Journal of Positioning, Navigation, and Timing
• /
• 제2권2호
• /
• pp.123-130
• /
• 2013

Autonomous agricultural machines that are operated in small-scale farmland frequently experience turning and changes in direction. Thus, unlike when they are operated in large-scale farmland, the steering control systems need to be controlled precisely so that travel errors can be minimized. This study aims to develop a control algorithm for improving the path tracking performance of a steering system by analyzing the effect of the setting of the waypoint, which serves as the reference point for steering when an autonomous agricultural machine moves along a path or a coordinate, on control errors. A simulation was performed by modeling a 26-hp tractor steering system and by applying the equations of motion of a tractor, with the use of a computer. Path tracking errors could be reduced using an algorithm which sets the waypoint for steering on a travel path depending on the radius of curvature of the path and which then controls the speed and steering angle of the vehicle, rather than by changing the steering speed or steering ratio which are dependent on mechanical performance.

• Journal of Electrical Engineering and Technology
• /
• 제12권1호
• /
• pp.236-248
• /
• 2017

A direct stator flux vector control scheme in discrete-time domain is proposed in this paper for the interior permanent magnet synchronous motor (IPMSM) drive to remove the proportional-integral (PI) controller from the direct torque control (DTC) scheme applied to IPMSM and to obtain faster dynamic response and lower torque ripple output. The output of speed outer loop is used as the desired torque angle instead of the desired torque in the proposed scheme. The desired stator flux vector in dq coordinate is calculated with a given amplitude. The state-space equations in discrete-time for IPMSM are established, the actual stator flux vector is estimated in deadbeat manner by a full-order state observer, and then the closed-loop control is achieved by the pole placement. The stator flux error vector is utilized to calculate the reference stator voltage vector. Extracting the angle position and amplitude from the estimated stator flux vector and estimating the output torque are eliminated for the direct feedback control of the stator flux vector. The proposed scheme is comparatively investigated with a PI-SVM DTC scheme by experiment results. Experimental results show the feasibility and advantages of the proposed control scheme.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2011년도 추계학술대회
• /
• pp.71-72
• /
• 2011

This paper presents a novel and direct dead time compensation method of the 3 phase inverter using space vector pulse width modulation(SVPWM) topology. In the turn on time calculation of the effective voltage, the dead time effect is directly compensated according to the current direction of the midium voltage reference. Since the turn on time of the effective voltage vector is affected by the dead time, the loss time is compensated to turn on time of the effective voltage vector. And the dead time is added to the calculated voltage vector switching times according to the current direction. For the more effective compensation, the direction of the midium phase current is considered by the practical direction and voltage drops in the power devices. The proposed method can compensate the dead time which is considered feedback error or direction of middle phase current without coordinate transform in added controller. The proposed dead time compensation scheme is verified by the computer simulation and experiments of 3 phase R L load.

• 한국측량학회지
• /
• 제17권2호
• /
• pp.145-152
• /
• 1999

제트추진연구소(JPL : Jet Propulsion Laboratory)에서는 매일 전세계에 분포된 정밀 측지용 GPS수신기의 광역망으로 부터 관측자료를 수집하고 분석하여 정밀한 GPS transmitter parameters (위성의 위치력 및 시계 보정값)를 산정하고 있으며 이를 이용한 자동화된 GPS 자료 해석 서비스를 제공하고 있다. 본 연구에서는 한측점의 2주파 GPS수신기로부터 획득한 위성관측자료를 E-mail 및 ftp(file transfer protocol)로 JPL의 주컴퓨터에 연결시켜 JPL의 정밀 GPS transmitter parameters 및 Gipsy/Oasis-II (GOA-II) s/w를 활용한 정밀절대측위(PPP : Precise Point Positioning)기법의 정밀도를 분석하고 PPP에 의한 GPS기준점 좌표의 산정 방안을 검토한 것이다. 검토결과, X, Y, Z 직교좌표계에서 수 cm급의 위치결정이 가능하였다.

• 로봇학회논문지
• /
• 제15권1호
• /
• pp.16-23
• /
• 2020

This paper describes an alignment algorithm that estimates the initial heading angle of AUVs (Autonomous Underwater Vehicle) for starting navigation in a sea area. In the basic dead reckoning system, the initial orientation of the vehicle is very important. In particular, the initial heading value is an essential factor in determining the performance of the entire navigation system. However, the heading angle of AUVs cannot be measured accurately because the DCS (Digital Compass) corrupted by surrounding magnetic field in pointing true north direction of the absolute global coordinate system (not the same to magnetic north direction). Therefore, we constructed an experimental constraint and designed an algorithm based on extended Kalman filter using only inertial navigation sensors and a GPS (Global Positioning System) receiver basically. The value of sensor covariance was selected by comparing the navigation results with the reference data. The proposed filter estimates the initial heading angle of AUVs for navigation in a sea area and reflects sampling characteristics of each sensor. Finally, we verify the performance of the filter through experiments.

• 한국안전학회지
• /
• 제33권3호
• /
• pp.65-70
• /
• 2018

Terrain data for disaster analysis in hazardous or disaster areas is not only important but also needs to be built quickly. In particular, the introduction of drones is in the early stages of research using drones in a variety of fields such as shooting, analyzing and managing hazardous areas. It is expected that drone will be faster, safer and more effective than existing data collection method in case of small scale disaster hazard area and disaster area where equipment or manpower input is difficult. Therefore, in this study, drone shooting was performed for hazardous areas in mountainous roads located in Samcheok city, Gangwon province, and ground reference points were measured by RTK-GPS. The measured data were converted into DSM (Digital Surface Model) data by coordinate correction using Pix4D postprocessing program and then applied to the analysis of the hazard area of mountainous area. As a result, it was shown that it is effective to identify the risk by using the basic terrain data obtained from the drones.

• 한국통신학회논문지
• /
• 제15권11호
• /
• pp.945-954
• /
• 1990

로보트 팔이 컨베이어를 추적하는 강인한 적응제어계를 작업좌표에서 설계하였다. 제안한 설계방식은 모델규범형 설계방식과 Popov의 초안정정리를 기본으로 하였고 보조입력을 사용하여 Lyapunov 함수 V(t)와 시간미분 V와의 比의 크기를 크게하여 속응성을 좋게하여 과도특성을 개선하였다. 설계변수{lambda} 와 하중함수 $L_K$에서 $L_K$의 값이 {lambda}의 값보다 작은 경우에는 계통이 안정하나 $L_K$의 값이 {lambda}의 값보다 큰 경우에는 계통이 불안정하였다.

• 설비공학논문집
• /
• 제28권7호
• /
• pp.293-298
• /
• 2016

A three-dimensional (3D) numerical model of the vertical ground-coupled heat exchanger is useful for analyzing the modern ground source heat pump system. Furthermore, a detailed description of the inner side of the exchanger allows to account for the effects of the thermal capacity. Thus, both methods are included in the proposed numerical model. For the ground portion, a FDM (Finite Difference Method) scheme has been applied using the Cartesian coordinate system. Cylindrical grids are applied for the borehole portion, and the U-tube configuration is adjusted at the grid, keeping the area and distance unchanged. Two sub-models are numerically coupled at each time-step using an iterative method for convergence. The model is validated by a reference 3D model under a continuous heat injection case. The results from a periodic heat injection input show that the proposed thermal capacity model reacts more slowly to the changes, resulting in lower borehole wall temperatures, when compared with a thermal resistance model. This implies that thermal capacity effects may be important factors for system controls.

• Journal of Computational Design and Engineering
• /
• 제2권4호
• /
• pp.253-260
• /
• 2015

Feature-based NC machining, which requires high quality of 3D CAD model, is widely used in machining aircraft structural part. However, there has been little research on how to automatically detect the CAD model errors. As a result, the user has to manually check the errors with great effort before NC programming. This paper proposes an automatic CAD model errors detection approach for aircraft structural part. First, the base faces are identified based on the reference directions corresponding to machining coordinate systems. Then, the CAD models are partitioned into multiple local regions based on the base faces. Finally, the CAD model error types are evaluated based on the heuristic rules. A prototype system based on CATIA has been developed to verify the effectiveness of the proposed approach.