• Journal of Computational Design and Engineering
• /
• 제3권4호
• /
• pp.349-362
• /
• 2016

The numerical solutions of unsteady hydromagnetic natural convection Couette flow of a viscous, incompressible and electrically conducting fluid between the two vertical parallel plates in the presence of thermal radiation, thermal diffusion and diffusion thermo are obtained here. The fundamental dimensionless governing coupled linear partial differential equations for impulsive movement and uniformly accelerated movement of the plate were solved by an efficient Finite Element Method. Computations were performed for a wide range of the governing flow parameters, viz., Thermal diffusion (Soret) and Diffusion thermo (Dufour) parameters, Magnetic field parameter, Prandtl number, Thermal radiation and Schmidt number. The effects of these flow parameters on the velocity (u), temperature (${\theta}$) and Concentration (${\phi}$) are shown graphically. Also the effects of these pertinent parameters on the skin-friction, the rate of heat and mass transfer are obtained and discussed numerically through tabular forms. These are in good agreement with earlier reported studies. Analysis indicates that the fluid velocity is an increasing function of Grashof numbers for heat and mass transfer, Soret and Dufour numbers whereas the Magnetic parameter, Thermal radiation parameter, Prandtl number and Schmidt number lead to reduction of the velocity profiles. Also, it is noticed that the rate of heat transfer coefficient and temperature profiles increase with decrease in the thermal radiation parameter and Prandtl number, whereas the reverse effect is observed with increase of Dufour number. Further, the concentration profiles increase with increase in the Soret number whereas reverse effect is seen by increasing the values of the Schmidt number.

• 대한기계학회논문집B
• /
• 제30권10호
• /
• pp.973-981
• /
• 2006

Recently there is an increasing interest in particulate matter emission because of new emission regulations, health awareness and environmental problems. It requires to improve particulate measurement techniques as well as to reduce soot emissions from combustion systems. As mentioned above, it is demanded that reduction techniques together with measurement techniques of exhausted particulate matters in combustion systems such as vehicles. However, measurement techniques of particulate matters should be prior to reduction techniques of that because it is able to know an increase and a decrease of exhausted particulate matters when measured particulate matters. Therefore, in this study, we report the measurement of soot primary-particle size using time-resolved laser induced incandescence (TIRE-LII) technique in laminar ethylene diffusion flame. As an optical method, laser induced incandescence is one of well known methods to get information for spatial and temporal soot volume fraction and soot primary particle size. Furthermore, TIRE-LII is able to measure soot primary particle size that is decided to solve the decay ate of signal S $(t_1)$ and S $(t_2)$ at two detection time. In laminar ethylene diffusion flame, visual flame height is 40 mm from burner tip and measurement points are height of 15, 20, 27.5, 30 mm above burner tip along radial direction. As increasing the height of the flame from burne. tip, primary particle size was increased to HAB(Height Above Burner tip)=20mm, and then decreased from HAB=27.5 mm to 30 mm. This results show the growth and oxidation processes for soot particles formed by combustion.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2004년도 제29회 KOSCI SYMPOSIUM 논문집
• /
• pp.231-237
• /
• 2004

Vacuum carburizing continues to gain acceptance as an alternative to atmosphere carburizing particularly in the car industry. The advantages of low-pressure carburization over atmospheric gas carburization is not only the creation of a surface entirely free of oxide and the environmentally friendly nature of these methods but also an improvement in deformation behaviour achieved by combining carburization with gas quenching, a reduction in batch times by increasing the carburization temperature, low gas and energy consumption and the prevention of soot to a large extent. In present study, an improved vacuum carburizing method is provided which is effective to deposit carbon in the surface of materials and to reduce cycle time. Also LPC process simulator was made to optimize to process controls parameters such as pulse/pause cycles of pressure pattern, temperature, carburizing time, diffusion time. The carburizing process was simulated by a diffusion calculation program, where as the model parameters are proposed with help the experimental results and allows the control of the carburizing process with good accordance to the practical results. Thus it can be concluded that LPC process control method based on the theoretical simulation and experimental datas appears to provide a reasonable tool for prototype LPC system.

• 한국지반공학회논문집
• /
• 제22권5호
• /
• pp.5-12
• /
• 2006

본 연구에서는 점토질 지반의 강도를 증진시키기 위해, 일련의 동전기 현상을 이용한 주입 실험을 수행하였다. 이를 위해 실내 Bench scale 실험을 실시하여 적용성을 파악하였다. 또한 확산의 영향에 의한 지반개량효과를 파악하기 위해 실험 종료 후 5일 간격으로 25일 동안 데인 실험을 실시하여 강도증진효과를 파악하였으며, 처리기간에 따른 영향을 고려하기 위해 5일 간격(5, 10, 15, 20, 25)으로 처리기간을 설정한 후 동전기 주입 실험을 실시하였다. 주입제 종류에 따른 실험결과, 초기 강도치와 비교하여 약 $2\sim7$배 정도의 강도증진효과가 발생하였으며, 특히 양극에 규산나트륨을 주입하고 음극에 인산을 주입한 경우 약 7배 정도의 강도증진효과가 발생하였다. 또한 확산과 함수비 감소에 따른 강도값을 분석해본 결과 시간경과에 따라 강도 값이 일정한 값으로 수렴하는 양상을 띠었으며, 함수비 감소에 의한 강도 증가치 보다 동전기 주입과 확산에 의한 영향으로 발생되는 강도증가치가 약 $700\sim1000%$ 높게 나타났다. 처리기간에 따른 실험결과, 처리기간이 증가함에 따라 동전기 주입에 의한 강도증진효과가 크게 나타났으며, 함수비 감소에 의한 강도증가치보다 대략 $3\sim4$배 정도 높게 나타남을 파악할 수 있었다.

• 한국환경보건학회지
• /
• 제24권1호
• /
• pp.62-69
• /
• 1998

It has been studied that the measurement of odor component emission at confectionery manufacture. The objects of this study were to investigate reduction of offensive odor. The survey effects of odorous materials are presented as follows. The countermeasure of operating process is to minimize sludge sediment in each unit facility. Especially, in summer, we have to clean the sludge frequently, because anaerobic decomposing is likely to occur easily. The sludge or scum from sedimentation tank pond, and floating tank should be treated quickly. We should avoid overloading operation. In the case of overloading, dissolved oxygen should be increased, the quality of wastewater input should be decreased. When dried cakes from condense tank or floating tank are left in treatment plant, we should cover, to prevent diffusion of smell with masking materials. The seasonal condition of operating should be fixed and the kind of coagulants should be changed because the wastewater in each season have different loading rates and organic materials. Odorous materials are very sensitive to the seasonal temperature variation. Especially, when the amount of rainfall is small and the high temperature of maintenance in long periods, air diffusion rate is large, so odorous materials can make great effect on surroundings comparision with other periods. To reduce odorous gas, as short term method, we had better take ceramic addition method. Especially, in summer we should take ceramic addition method. Also, as long term method, the size of wastewater treatment facility is the most important in the normal operating of wastewater treatment facility. But wastewater treatment facilities in this factory are too old, treatment process is old fashion, and the size is too small. So, large wastewater quantity to treat in summer. As results, the expansion of wastewater treatment facility and the process of improvement are required. Restriction level of odor was exceed. As it is overloaded in summer, the basis cause of odor is that the size of wastewater treatment facility is small. The prediction of air quality equilibrium density variation show that the odorous materials from working place are Amine materials whose smell strength is about 2.5(a little strong degree). We can suppose that in summer is sensitive to temperature variation, smell strength is larger as to reduce the origin of odor. We must expand wastewater treatment facility and improve the process A.S.A.P.

• Structural Engineering and Mechanics
• /
• 제76권5호
• /
• pp.599-611
• /
• 2020

A state-space method is developed to investigate the time-dependent behaviors of an angle-ply cylindrical shell in cylindrical bending with surface-bonded piezoelectric layers. Both the interfacial diffusion and sliding are considered to describe the properties of the imperfect interfaces. Particularly, a matrix reduction technique is adopted to establish the transfer relations between the elastic and piezoelectric layers of the laminated shell. Very different from our previous paper, in which an approximate numerical technique, i.e. power series expansion method, is used to deal with the time-dependent problems, the exact solutions are derived in the present analysis based on the piezoelasticity equations without any assumptions. Numerical results are finally obtained and the effects of imperfect interfaces on the electro-mechanical responses of the laminated shell are discussed.

• 소성∙가공
• /
• 제22권8호
• /
• pp.463-469
• /
• 2013

In the previous work, a new forging process design, which included incremental upsetting, diffusion bonding and cogging, was suggested as a method to manufacture 1.9wt%C ultrahigh carbon workrolls. The previous study showed that incremental upsetting and diffusion bonding are effective in closing voids and healing of the closed void. In addition, compression tests of the 1.9wt%C ultrahigh carbon steel revealed that new microvoids form within the blocky cementite at temperatures of less than $900^{\circ}C$ and that local melting can occur at temperatures over $1120^{\circ}C$. Thus, the forging temperature should be controlled between 900 and $1120^{\circ}C$. Based on these results, incremental upsetting and diffusion bonding were used to check whether they are effective in closing and healing voids in a 1.9wt%C ultrahigh carbon steel. The incremental upsetting and diffusion bonding were performed using sub-sized specimens of 1.9wt%C ultrahigh carbon steel. The specimen was deformed only in the radial direction during the incremental upsetting until the reduction ratio reached about 45~50%. After deformation the specimens were kept at $1100^{\circ}C$ for the 1 hour in order to obtain a high bonding strength for the closed void. Finally, microstructural observations and tensile tests were conducted to investigate void closure behavior and bonding strength.

• 한국염색가공학회:학술대회논문집
• /
• 한국염색가공학회 2001년도 추계학술발표회 논문집
• /
• pp.3-11
• /
• 2001

Fundamental studies at the CSIRO division of Wool technology and ICI on the diffusion of dyes into wool〔1,2〕have let to development of a new approach to wool dyeing. In this method, the cell membrane complex of wool is modified before dyeing by treatment under mildly alkaline conditions with a special chemicals. Wool pretreated with ethoxylated quaternary ammonium salt has an increased rate of dyebath exhaustion and dye penetration early in the dyeing cycle. This enables the treated material to be dyed below the boil for a similar time to the conventional cycle. This technique can be used on untreated and shrinkresist-treated wool and wool/nylon blends. In addition to good macro-levelness and excellent coverage of tippiness, the low temperature dyeing process give higher exhaustion levels of dyestuffs and insect-resist agent and hence cleaner effluent liquors, compared with conventional dyeing process. Low Temperature Dyeing process cause significantly less fiber damage than conventional way. The reduction in damage is reflected in improved processing performance of the dyed wool.

• 한국미생물·생명공학회지
• /
• 제39권4호
• /
• pp.387-389
• /
• 2011

우리의 이전의 연구에서 Citrus auranifoli 오일은 Malassezia furfur와 Malassezia pachydermatis에 대해 항곰팡이 활성을 나타낸다는 것을 보여주었다. 본 연구에서 Citrus auranifoli 오일의 주요 성분인 리모넨(limonene)의 M. furfur와 M. pachydermatis에 대한 저해효과를 디크스 확산 방법(disk diffusion method)에 의해 측정하였고, Beas-2B 세포에 대한 세포독성을 cytopathic effect reduction 방법에 의해 측정하였다. Limonene의 최소곰팡이저해농도(minimum fungicidal concentration)는 양성대조구인 itraconazole보다 더 낮았고, 100 ${\mu}g$/mL의 농도에서 Beas-2B cells에 대한 세포독성을 나타내지 않았다. 그러나 itraconazole은 같은 농도에서 약한 세포독성을 나타내었다. 그러므로, 우리의 결과에서 limonene는 비세포독성과 함께 M. furfur and M. pachydermatis의 성장저해를 하는데 효과적이라는 것을 보여준다.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1997년도 춘계학술대회
• /
• pp.379-382
• /
• 1997

A method for measuring optical properties of biological medium was investigated by using the frequency domain spectroscopy. When amplitude-modulated light with the frequency of several tens up to several hundred MHz propagates through a scattering medium, the phase lag and the amplitude reduction occur. The phase lag depends on the average of optical path lengths. The amplitude reduction with respect to the radial distance is influenced by the penetration depth. The mean of optical path length and penetration depth are related to optical coefficients. The phase lag and the amplitude reduction were measured based on the heterodyne detection method. The experimental data were fitted with the theoretical curves derived from diffusion theory and the absorption and scattering coefficients were calculated.