• The Journal of Korean Academy of Prosthodontics
• /
• v.14 no.1
• /
• pp.47-54
• /
• 1976

Pulpal temperature is changed in response for various conditions which were mechanical, thermal, chemical and biological stimuli. This study was performed to determine the pulpal temperature changes which were using air turbine with air-water coolant, water coolant, and conventional dental engine with water coolant and no coolant on 28 canine of dogs. In order to record pulpal temperature, pulp chamber was opened on the labiocervical area of canine. Thermocouple was inserted into pulp chamber and was fixed with filling material(dycal). Changes of pulpal temperature were recorded on the physiograph, which had been standardized temperature degree, through thermocouple to thermistor bridge and carrier preamplifier. The amount of experimental temperature change to that of control was interpreted in the pulpal cavity. The obtained results were as followings: 1. The mean normal temperature was 33.07 centigrade. 2. The temperature was decreased than normal pulpal temperature. It was 12.04 centigrade in reduction by air turbine with air-water coolant, 7.17 centigrade in reduction by air turbine with air coolant, 5.54 centigrade in reduction by conventional engine with water coolant, and 1.26 centigrade in reduction by conventional engine with no coolant. 3. The time for maximal temperature change was 53.3 seconds in reduction by air turbine with air-water coolant, 73.4 seconds in reduction by air turbine with air coolant, 50.9 seconds in reduction by conventional engine with water coolant, and 27.1 seconds in reduction by conventional engine with no coolant. 4.. After reduction was ceased, the recovery time to normal pulp temperature was 287.1 seconds in air turbine with air-water coolant, 189.0 seconds in air turbine with air coolant, 86.9 seconds in conventional engine with water coolant, and 52.9 seconds in conventional engine with no coolant respectively.

• Journal of radiological science and technology
• /
• v.41 no.2
• /
• pp.115-122
• /
• 2018

We aims to perform comparative analysis on the dose area and image qualities varying on the slice thickness when using Automatic Exposure Controller (AEC) and manual exposure; thus, it wants to suggest a measure to reduce exposure dose by setting the optimal examination condition for each slice thickness. The method was to set the thickness as Thin, Normal, and Heavy adult and evaluate the dose area, spatial resolution, low contrast resolution, Signal to Noise Ratio (SNR) and Contrast to Noise Ratio (CNR) according to each slice thickness by using the AEC and the manual exposure controller. The dose area according to each slice thickness all increased both when using the AEC and the manual exposure. However, the manual exposure showed lower dose area product than the AEC. Spatial resolutions and low contrast resolutions were all observed to be higher than the evaluation standard. Also, the SNR and CNR of each thickness all increased when using the AEC. When using the manual exposure, SNR and CNR increased in all cases other than the Heavy Adult. Consequently, the Thin and Normal Adult showed dose reduction about 2 times when using the manual exposure controller, while ensuring the image quality. Heavy adult was able to maintain good image quality by using AEC.

• The Korean Journal of Ecology
• /
• v.26 no.4
• /
• pp.165-172
• /
• 2003

The objectives of this study were to examine the physiological responses to ozone and to measure ozone uptake rates of Betula species exposed to relatively high concentration of pollutants. At the end of the growing season, photosynthesis, pigments contents, antioxidants (SOD and GR) and ozone uptake rates were measured or estimated at the leaves of five Betula species (Betula costata, B. davurica, B. platyphylla var. japonica, B. schmidtii and B. ermanii) exposed to 100ppb ozone concentration. On the termination of the experiment, growth effects were determined by measuring leaf area and dry weights of leaf, stem and root. Ozone treatment showed the significant reduction the leaf area and dry weight of four Betula species, except for B. ermanii. Shoot / root (SR) ratio of five species represented two different types. SR ratio of B. costata and B. davurica were lower than control, in contrast, SR ratio of B. platyphylla var. japonica, B. schimidtii and B. emani, were higher than that of control. The photosynthetic responses of five species were different in responses to ozone exposure. Four species, except for B. emanii, maintained or increased the stomatal conductance, but B. emanii decreased both stomatal conductance and photosynthesis. SOD activities of five species decreased by the ozone exposure, especially B. ermanii showed the largest reduction, GR activities of B. platyphylla var. japonica and B. schmidtii increased, B. costata and B. emanii decreased. Instantaneous ozone uptake rate was the highest at the leaves of B. ermanii and B. costata, ozone uptake per seedling was the highest at the leaf of B. schmidtii and B. emanii. It was concluded that B. costata, B. davurica and B. platyphylla var. japonica, appeared the growth reduction and visible ozone injury, were sensitive species to ozone, and B. schmidtii with the increased antioxidant activity and B. ermanii without the growth reduction were relatively resistant species to high ozone concentration at the early growing stage.

• Tribology and Lubricants
• /
• v.33 no.1
• /
• pp.1-8
• /
• 2017

Drag torque reduction in a wet clutch pack is a key aspect of the design process of the dual clutch transmission (DCT) system. In order to reduce the drag torque caused by lubricant shear resistance, recently developed wet clutch pack systems of DCT, as well as automatic transmission and other four-wheel drive (4WD) couplings, frequently utilize wavy wet clutch pads. Therefore, wavy shape of friction pad are made on the groove patterns like waffle pattern for the reduction of drag torque. Additionally, the groove patterns are designed with larger channels at several locations on the friction pad to facilitate faster outflow of lubricant. However, channel performance is a function of the waviness of the friction pad at the location of the particular channel. This is because the discharge sectional area varies according to the waviness amplitude at the location of the particular channel. The higher location of the additional channel on the friction pad results in a larger cross-sectional area, which allows for a larger flow discharge rate. This results in reduction of the drag torque caused by the shear resistance of DCTF, because of marginal volume fraction of fluid (VOF) in the space between the friction pad and separator. This study computes the VOF in the space between the friction pad and separator, the hydrodynamic pressure developed, and the shear resistance of friction torque, by using CFD software (FLUENT). In addition, the study investigates the dependence of these parameters on the location and waviness amplitude of the channel pattern on the friction pad. The paper presents design guidelines on the proper location of high waviness amplitude on wavy friction pads.

• Journal of Korean Physical Therapy Science
• /
• v.9 no.1
• /
• pp.1-8
• /
• 2002

This study set out to investigate what kind of effects the consistent visual stimuli and verbal and non verbal auditory stimuli have on pain alleviation, as well as to see the influence of joint application of visual and auditory stimuli at the same time on pain alleviation, according to lightness of 50lux and 200lux, ultimately providing basic data in setting up an environment in case of treating pain. The subject were comprised of 30 male and female adults with pain in the neck and back area. The subject were treated in their pain area with Transcutaneous Electrical Nerve Stimulator(TENS) 100HZ for 20 minutes in the research set where each visual, auditory, and joint visual and auditory stimuli was given. For analysis methods, Visual Analogue Scale(VAS) and McGill Pain Questionnaire were adopted to see the changes before and after treatment, and the electrocardiogram, systolic and diastolic pressure, number of heart rate and breathing frequence and endorphin were compared and analyzed using the Wilcoxon singed-rank test. And The Kreskal-walllis test was used to compare the two subgroups from each group. Wilcoxon singed-rank test and the Kreskal-walllis test was used to compare the two subgroups from each group. The results were as follows: 1. The group of 50lux and 200lux were compared given varying degrees of visual stimuli. The group of 200lux showed more reduction in pain points, average systolic and diastolic pressure and average endorphin. 2. The group of verbal and non verbal were compared given varying degrees of auditory stimuli. The group of non-verbal showed more reduction in average systolic and diastolic pressure. 3. The group of 200lux+verbal and 200lux+non verbal were compared given varying degrees of joint visual and auditory stimuli. There was found a statistical significance(p<0.05) in endorphin between the two groups, with more endorphin reduction for 200lux+non verbal group. And there was a statistically significant reduction in VAS and McGill before and after the treatment between the two groups.

• Korean Journal of Materials Research
• /
• v.13 no.9
• /
• pp.631-634
• /
• 2003

To fabricate W-Cu nanocomposite powder, $WO_3$-CuO powder mixture was high-energetically ball-milled and subsequently hydrogen-reduced. The effect of ball-milling on the hydrogen-reduction behavior of$ WO_3$-CuO was investigated with non-isothermal hygrometric analysis during hydrogen-reduction. Increasing the ball-milling time, the reduction peak temperatures of humidity curves were shifted to low temperature. It was considered that the reduction temperature should be decreased because the specific surface area of each oxide considerably increased with increasing the ball-milling time. In case of ball-milling for 0 h, $WO_3$and CuO were independently hydrogen-reduced and W particles were nucleated on the surface of Cu adjacent to W by CVT. However, in case of ball-milling for 50 h, the aggregates of about 200-300 nm were observed. W particles of size below 30-50 nm were homogeneously distributed with Cu in the aggregates.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.17 no.4
• /
• pp.257-274
• /
• 2001

To properly prepare teeth, dentists require a direct view of the working area and are often placed in a difficult position, moreover, a high proportion of dentists suffer from headache and back pain. Dentists who make use of the dental mirror and position their patients carefully to gain a proper view report less headache, pain and discomfort in the shoulders. It is recommended that dentists learn the "Home Position(H.P.)" which among the various "Random Position(R.P.)" methods, enables dentists to approach their patients in a stable posture. The purpose of this study was to compare tooth preparation in the H.P. and the R.P., and evaluate the clinical efficacy of the H.P.. Tooth preparation for a full cast crown was performed on the maxillary left 1st molar using the H.P. and the R.P., and the shapes of the prepared tooth surfaces at the two different operating positions were compared. The amount of occlusal reduction, marginal width, height, and axial taper were measured and analyzed. A T-test was performed separately to compare the results of the H.P. and the R.P. with respect to the accuracy of the corresponding tooth reduction. The results were as follows. ; 1. The amount of occlusal reduction was excessive on the mesiobuccal cusp(P<0.05), and deficient on the lingual cusp in the H.P.(P<0.01). In the R.P., this was excessive on the buccal cusp and deficient on the fossa and distolingual cusp(P<0.01). 2. The amounts of marginal width were excessive in all areas except on the lingual and mesial surfaces in the H.P. and lingual surface in the R.P.(P<0.01). 3. The marginal heights were achieved more accurately in the R.P. than the H.P.(P<0.01). 4. Axial surface taper was excessive in all areas in the H.P.(P<0.01). But the axial taper of measured areas was even, and tooth is more like to retain its original axis after reduction. In the R.P., axial surface taper was excessive on the mesial and buccal area, and deficient on the distolingual area(P<0.01), and therefore, the axis of the prepared teeth was tipped in the distolingual direction. 5. The times needed for preparation were 12 minutes and 49 seconds in the H.P., and 11 minutes and 35 seconds in the R.P., and the R.P. was statistically faster(P<0.01). The tooth preparation in the H.P. achieved its goal, in that it enabled the operator to make even tooth reduction. In conclusion, the H.P. system offers an improved method that can be used in clinic after specific training.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.7 no.4
• /
• pp.85-95
• /
• 2007

The variation of hydraulic and hydrologic aspect of urban area according to the strongly seasonal variation of rainfall and the increment of urbanization has caused the runoff variation and increased the flood damage, and thus made a difficulty to manage water resources in urban area. Recently, as a part of efforts to resolve these problems, the facilities for reducing runoff increasing due to urbanization have a tendency to install in our country. In this study, more effective Infiltration-Storage System(ISS) is proposed and its reducing effect is analyzed by hydraulic experimental study. The infiltration characteristics of runoff reduction facilities are examined as varying artificial rainfall and a material of infiltration layers being able to consider the influence of urban development. As a result of comparison of infiltration rate of the upper and lower parts, the infiltration rate in the lower part is larger than that of the upper part. Thus, the ISS is more available than existing runoff reduction facilities. Results obtained in this study can be provided fundamental data for improvement of existing runoff reduction facilities and practical use of ISS.

• Journal of Powder Materials
• /
• v.8 no.3
• /
• pp.151-156
• /
• 2001

MgO based nanocomposite powder including ferromagnetic iron particle dispersions, which can be available for the magnetic and catalytic applications, was fabricated by the spray pyrolysis process using ultra-sonic atomizer and reduction processes. Liquid source was prepared from iron (Fe)-nitrate, as a source of Fe nano-dispersion, and magnesium (Mg)-nitrate, as a source of MgO materials, with pure water solvent. After the chamber were heated to given temperatures (500~$^800{\circ}C$), the mist of liquid droplets generated by ultrasonic atomizer carried into the chamber by a carrier gas of air, and the ist was decomposed into Fe-oxide and MgO nano-powder. The obtained powders were reduced by hydrogen atmosphere at 600~$^800{\circ}C$. The reduction behavior was investigated by thermal gravity and hygrometry. After reduction, the aggregated sub-micron Fe/MgO powders were obtained, and each aggregated powder composed of nano-sized Fe/MgO materials. By the difference of the chamber temperature, the particle size of Fe and MgO was changed in a few 10 nm levels. Also, the nano-porous Fe-MgO sub-micron powders were obtained. Through this preparation process and the evaluation of phase and microstructure, it was concluded that the Fe/MgO nanocomposite powders with high surface area and the higher coercive force were successfully fabricated.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.398-403
• /
• 2001

There is a potential usability of electric arc furnace(EAF) dust produced during the iron manufacturing process as a recycled resource, because valuable materials such as Zn, Pb and Fe are contained in it. In this study, metallic Zn was recycled from the fine electric arc furnace dust by a solid state reduction method using carbon at relatively low temperature. It was possible to recover metallic zinc by using of high vapour pressure of zinc with this reduction method. The feasibility of recycled zinc for cold bonded pellet(CBP) was investigated. The main composition of EAF dust were franklinite(ZnFe$_2$O$_4$), magnetite(Fe$_3$O$_4$) and zincite(ZnO), and Pb and Cl were completely removed by a heat treatment in oxidation environment. The reduction ratio increased as the solid carbon content increased, and it increased with decreasing of dust particle size and increasing of compaction pressure due to a increase of contact area.