• Transactions of Materials Processing
• /
• v.7 no.1
• /
• pp.36-48
• /
• 1998

In order to analyze the stretch flange forming characteristics of tailored blanks. laser welded blanks of different thickness and strength combinations were prepared and hole expansion tests were done. The stretch flange formability of laser welded blanks was reduced as increasing the deformation restraining force($strength{\times}thickness$) ratio between two welded sheets. Simulation of stretch forming mode deformation and comparson with experimental results showed that the stretch flange formabili-ty was influenced not only by the difference of the deformation restraining forces between two base sheets but also by the difference of the deformation restraining forces between base sheet and weld. Therefore the stretch flange formability was reduced more rapidly than tensile elongation as increas-ing the deformation restraining force ration. It was also found that simulation of stretch flange forming was more accurate when material properties of weld was given.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.251-258
• /
• 2008

The use of reinforced earth walls in permanent structures is getting it's popularity. Despite a number of advantages of reinforced earth walls over conventional concrete retaining walls, there exit concerns over long-term residual deformation when subjected to repeated and/or cyclic loads, during their service period. In this investigation, the effect of preloading in reducing long term residiual deformation of back-to-back reinforced soil wall under sustained and/or repeated loading enviormentment using a series of reduced-scale model tests. It is found that the preloading technique can be an effective means of controlling residual deformations of reinforced soils under varisous loading conditions.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.121-130
• /
• 2006

Despite a number of advantages of reinforced earth walls over conventional concrete retaining walls, there exit concerns over long-term residual deformation when used as part of permanent structures. In view of these concerns, time-dependant deformation characteristics of geosynthetic reinforced modular block walls under sustained loads were investigated using reduced-scale model tests. The results indicated that a sustained load can yield appreciable magnitude of residual deformation, and that the magnitude of residual deformation depends on the loading characteristic as well as reinforcement stiffness.

• Journal of the Korean Geosynthetics Society
• /
• v.5 no.1
• /
• pp.1-7
• /
• 2006

Despite a number of advantages of reinforced earth walls over conventional concrete retaining walls, there exit concerns over long-term residual deformation when used as part of permanent structures. In view of these concerns, time-dependant deformation characteristics of geosynthetic reinforced modular block walls under sustained loads were investigated using reduced-scale model tests. The results indicated that a sustained load can yield appreciable magnitude of residual deformation, and that the magnitude of residual deformation depends on the loading characteristic as well as reinforcement stiffness.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.03b
• /
• pp.79-86
• /
• 2000

This paper presents the results of a parametric study on the behavior of tunnel face reinforced with horizontal pipes. A series of reduced-scale model tests was carried out to in an attempt to verify previously performed three-dimensional numerical modeling and to investigate effects of reinforcement layout on the tunnel face deformation behavior The results of model tests indicate that the tunnel face deformation can significantly reduced by pre-reinforcing the tunnel face with longitudinal members and thus enhancing the tunnel stability. In addition, the model tests results compare fairly well with those from the previously performed three-dimensional finite element analysis. Therefore, a properly calibrated three dimensional model may effectively be used in the study of tunnel face reinforcing technique.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.11 no.3
• /
• pp.57-64
• /
• 2002

Finite element program(ANSYS) estimated thermal deformation quantity in high frequency heat treatment process of a machine tool fred drive system slideway and apply deformation quantity in roughing process. Having processed the heat treatment minimizing methods of the quantity of deformation heat treatment process. Having done heat treatment with high frequency after taper processing with considering the existed heat treatment generating the quantity of deformation, existed quantity of deformation can be reduced down to 80%, consequently productivity and material saving can be achieved. When high frequency heat treatment finite element method estimated deformation quantity at difference temperature and time, it is progress at cost don and saved time.

• Computational Structural Engineering
• /
• v.10 no.2
• /
• pp.139-148
• /
• 1997

A finite element method is programmed to analyse the nonlinear behavior of axisymmetric structures. The lst order Mindlin shell theory which takes into account the transversal shear deformation is used to formulate a conical two node element with six degrees of freedom. To evade the shear locking phenomenon which arises in Mindlin type element when the effect of shear deformation tends to zero, the reduced integration of one point Gauss Quadrature at the center of element is employed. This method is the Updated Lagrangian formulation which refers the variables to the state of the most recent iteration. The solution is searched by Newton-Raphson iteration method. The tangent matrix of this method is obtained by a finite difference method by perturbating the degrees of freedom with small values. For the moment this program is limited to the analyses of non-linear elastic problems. For structures which could have elastic stability problem, the calculation is controled by displacement.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.2 no.2
• /
• pp.31-36
• /
• 2003

Base and saddle feed drive system in machine tool puts in operation for Improvement of life and endure by high frequency heat treatment. In this time, work requirement of establishment to gets by repeat experimentation. In this paper, using the finite elementary method, we predict and revision processing, and gets minimizing of deformation and reduce the progress of Grinding works. Moreover, having high frequency heat treatment, the maximum deformation genesis m the middle parts without slideway length. Take deformation Into finite element program (ANSYS) of taper process in roughing process, after having high frequency heat treatment, existed quantity of deformation can be reduced down to 80 percents.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.03a
• /
• pp.293-297
• /
• 1998

A method for the evaluation and the compensation of the vertical milling machine is presented. The method used a mathmatical model of thermal deformation based on temperatur variations of the machine and the environment. It follows an empirical approach and requires low cost equipment to be applied. According to this study, machine error caused by thermal deformation will be reduced to about 1/6.

• Proceedings of the KIEE Conference
• /
• 2007.11c
• /
• pp.183-186
• /
• 2007

Realistic deformation of computer simulated anatomical structures is computationally intensive. As a result, simple methodologies not based in continuum mechanics have been employed for achieving real time deformation of virtual reality. Since the graphical interpolations and simple spring models commonly used in these simulations are not based on the biomechanical properties of tissue structures, these "quick and dirty"methods typically do not accurately represent the complex deformations and force-feedback interactions that can take place during surgery. Finite Element(FE) analysis is widely regarded as the most appropriate alternative to these methods. However, because of the highly computational nature of the FE method, its direct application to real time force feedback and visualization of tissue deformation has not been practical for most simulations. If the mathematics are optimized through pre-processing to yield only the information essential to the simulation task run-time computation requirements can be drastically reduced. To apply the FEM, We examined a various in verse matrix method and a deformed material model is produced and then the graphic deformation with this model is able to force. As our simulation program is reduced by the real-time calculation and simplification because the purpose of this system is to transact in the real time.