• Structural Engineering and Mechanics
• /
• 제7권3호
• /
• pp.289-302
• /
• 1999

An approximate method for analyzing the bending problems of irregular-shaped plates is proposed. In this paper irregular-shaped plates are such plates as plate with opening, circular plate, semi-circular plate, elliptic plate, triangular plate, skew plate, rhombic plate, trapezoidal plate or the other polygonal plates which are not uniform rectangular plates. It is shown that these irregular-shaped plates can be considered finally as a kind of rectangular plates with non-uniform thickness. An opening in a plate can be considered as an extremely thin part of the plate, and a non-rectangular plate can be translated into a circumscribed rectangular plate whose additional parts are extremely thin or thick according to the boundary conditions of the original plate. Therefore any irregular-shaped plate can be replaced by the equivalent rectangular plate with non-uniform thickness. For various types of irregular-shaped plates the convergency and accuracy of numerical solution by proposed method are investigated.

• 대한기계학회논문집B
• /
• 제28권3호
• /
• pp.304-314
• /
• 2004

An experimental study has been conducted to measure the temperature fields and the local film cooling effectiveness for two and three staggered rows of the rectangular shaped-holes with various blowing rates. The hydraulic diameter of rectangular-shaped hole is 10mm. To compare with the film cooling performance of rectangular-shaped hole, two kinds of circular holes are tested. One has the same hydraulic diameter as the rectangular hole and the other has the same cross sectional area. Also, rectangular holes with expanded exit with same inlet area as rectangular ones are tested. Temperature fields are measured using a thermocouple rake attached on three-axis traversing system. Adiabatic film cooling effectiveness on the surface are obtained based on experimental results of thermochromic liquid crystals. The film cooling effectiveness is measured for various blowing rates and compared with the results for the cylindrical holes. In case of 2 rows, the rectangular holes has better performance than circular holes due to its slot-like geometry. In case of 3 rows, the effecta of hole shape is not clear.

• 한국기계가공학회지
• /
• 제14권2호
• /
• pp.99-104
• /
• 2015

This study analyzed the effects on displacement and stress as a result of improving the profile fastening method targeting rectangular-shaped and cube-shaped specimens. For the rectangular-shaped specimens, the improved fastening method reduced maximum displacement to 41.7% and maximum stress to 18.3% compared to the existing fastening method. For the cube-shaped specimens, maximum displacement and maximum stress results were found to be similar to those of the rectangular-shaped specimens. Thus, as a result of comparing the stress and displacement of the existing and improved fastening methods, it was found that the improved fastening method is superior to the existing fastening method in terms of load support.

• 설비공학논문집
• /
• 제14권5호
• /
• pp.365-376
• /
• 2002

An experimental study has been conducted to measure the local film-cooling effectiveness and the heat transfer coefficient for a single row of rectangular-shaped holes. four different cooling hole shapes such ai a straight rectangular hole, a rectangular hole with laterally expanded exit, a circular hole and a two-dimensional slot are tested. A technique using thermochromic liquid crystals determine adiabatic film cooling effectiveness values and heat transfer coefficients on the test surface. Both film cooling effectiveness and heat transfer coefficient are measured for various blowing rates and compared with the results of the cylindrical ho1es and the two-dimensional slot. The flow patterns downstream of holes are calculated numerically using a cummercial package. The results show that the rectangular hopes provide better peformance than the cylindrical holes. For the rectangular holes with expanded exit, the penetration is reduced significantly, and the higher and more uniform cooling Peformance is obtained even at relatively high blowing rates.

• 상하수도학회지
• /
• 제23권5호
• /
• pp.573-581
• /
• 2009

In the case that the average velocity within rectangular-shaped sedimentation basin is less than 1.5cm/sec, and Froude number less than $10^{-6}$, it can not be expected that the longitudinal baffle improves the sedimentation efficiency. Also, since relatively lower velocity increases the effect of geostrophic body force, asymmetric flow pattern on a plane occurs within the basin. From the results of CFD (Computational Fluid Dynamics) simulation, in the case that the highest velocity within rectangular-shaped sedimentation basin is over 1.5cm/sec, and Froude number over $10^{-6}$, it can be expected that the longitudinal baffle installed within rectangular-shaped sedimentation basin improves the sedimentation efficiency.

• 한국전기전자재료학회논문지
• /
• 제18권5호
• /
• pp.457-463
• /
• 2005

This paper presents a method for analyzing irregular shaped power distribution networks. The irregular shaped metal-dielectric-metal plane is split into several piece of rectangular segments to calculate the impedance of the irregular shaped plane. Impedance matrix for each rectangular segments is calculated using the Mobius transform method to reduce the calculation time. Then the segmentation and do-segmentation method is applied to the piece of rectangular segments. Applied to the 6 inch by 5 inch size irregular shaped board, the proposed method shows 10 times faster than the electromagnetic or circuit analysis method.

• 소성∙가공
• /
• 제8권4호
• /
• pp.331-339
• /
• 1999

In this study, to analyze the shaped drawing process from round bar, the practical conical die with considering die radius and bearing was defined by a mathematical expression, and also a simple technique for initial mesh generation to the shaped drawing process was proposed. The drawing of rectangular section from round bar, one of the shaped drawing process, has been simulated by using non-steady state 3D rigid plastic finite element method in order to evaluate the influence of semi-die angle and reduction in area to corner filling. Other process variables such as friction constant, rectangular ratio, die radius and bearing length were fixed during the simulation. An artificial neural network has been introduced to obtain the optimal process conditions which gave rise to a fast simulation.

• International Journal of Aeronautical and Space Sciences
• /
• 제18권3호
• /
• pp.395-402
• /
• 2017

The local heat transfer and total pressure drops of developed turbulent flows in the ribbed rectangular convergent/divergent channels with ${\Lambda}/V-shaped$ ribs have been investigated experimentally. The channels have the exit hydraulic diameter ($D_{ho}$) to inlet hydraulic diameter ($D_{hi}$) ratios of 0.67 for convergence and 1.49 for divergence, respectively. The ${\Lambda}/V-shaped$ ribs with three different flow attack angles of $30^{\circ}$, $45^{\circ}$, and $60^{\circ}$ are manufactured with a fixed rib height (e) of 10 mm and the ratio of rib spacing (S) to height (e) of 10 on the walls. Thermal performances of the ribbed rectangular convergent/divergent channels are compared with the smooth straight tube under identical pumping power. The results show that the flow attack angle of $45^{\circ}$ with ${\Lambda}-shaped$ rib has the greatest thermal performance at all the Reynolds numbers studied in the convergent channel; whereas, the flow attack angle of $60^{\circ}$ with V-shaped rib has the greatest thermal performance over Reynolds number of 30,000 in the divergent channel.

• Coupled systems mechanics
• /
• 제11권3호
• /
• pp.233-257
• /
• 2022

This work presents a comparative study between two different models: trapezoidal and T-shaped combined footings. The comparative study between trapezoidal and T-shaped combined footings presented in this paper generatesresultsthat have an unparalleled accuracy for all foundation engineering problems. The main part of this research is to obtain the optimal area, reinforcing steel, and thickness of the trapezoidal and T-shaped combined footings using the new models. The comparison is made for two trapezoidal combined footings and two T-shaped combined footings ofreinforced concrete subjected to the same load.Themain findings are: themodelfortrapezoidal combined footings can be used for rectangular and triangular, and the T-shaped combined footings can be used for rectangular. The structure of the paper is asfollowsfirst a very complete state of the art with extensive referencesthat describesthe methodology used for the different models clearly, presents different numerical examples, results and at the end conclusions.

• 한국전산유체공학회지
• /
• 제20권2호
• /
• pp.96-102
• /
• 2015

In this study, the green water phenomena on rectangular shaped structure is numerically simulated by STAR-CCM+ to investigate the flow pattern including the velocity profiles in bubbly water flow. 5 phases of the formation of green water in front of and over the rectangular shaped structure is simulated at the design condition which is scaled down by 1:125 from FPSO operating in GOM. All numerical results are compared with the experimental results performed in a two dimensional wave flume. The water deformation due to the green water are obtained by the high speed CCD camera with employing the shadow graphy technique, which is allowed to take the bubbly water flow into images. A series of image taken by shadow graphy technique is analyzed with MQD method to calculate the velocity in bubbly water flow.