• 설비공학논문집
• /
• 제4권1호
• /
• pp.48-56
• /
• 1992

The purpose of this study was to investigate the enhancement of heat transfer without additional external power in the case of rectangular air jet impinging vertically on the flat heating surface. In an attempt to enhance the heat transfer rate in two-dimensional impinging jet, the technique used in the present study was placement of square rod bundles as a turbluence promoter in front of the heat transfer surface. The effects of the clearance between the flat plate and square rod, and the nozzle exit velocity on the heat transfer characteristics have been investigated experimentally. The results obtained through this study were summerized as follows. High heat transfer enhancement was achived by means of flow acceleration and thinning of boundary layer by inserting rods in front of the heating flat plate. The smaller the clearance between rod and heating plate was, the larger heat transfer effect became. Average Nusselt number reached maximum at $Re=5.76{\times}10^4$ and C＝1㎜ and the enhancement rate of heat transfer became maxium at this condition with the enhancement ratio as high as about 1.427 when normalized by the flat plate value. The correlating equation of average Nusselt number and Reynolds number was obtained, which is $\bar{N}uo=1.324{\cdot}Re^{0.459}{\cdot}(C/A)^{-0.034}$.

• International Journal of Automotive Technology
• /
• 제8권2호
• /
• pp.185-191
• /
• 2007

The new FMVSS 208, 213, 225 regulations include automatic suppression of airbags to prevent low-risk airbag deployment and the use of child seats with a rigid-bar anchor system. The regulations mean that children must sit in the rear seat, but do not include other specific safety measures for their protection. In the rear, restraint equipment consists of three-point shoulder/lap belts for the outside seats and a static two-point lap belt in the middle, with no additional devices such as pretensioners or load limiters; this is far from optimal for children. This study investigated injury rates using a 3-year-old-child dummy. ECE R44 sled tests used a booster, a speed of 48 km/h, and a 26- to 32-g rectangular deceleration pulse. While seated on a booster, the dummies were restrained by an adult shoulder/lap three-point belt. HIC_15 msec, Chest G and Nij were somewhat lower with an emergency locking retractor (ELR)+pretensioner+load limiter than with only an ELR or with ELR+pretensioner. However, the current seat-belt system results in injury rates that exceed the limit for OOP performance under the new FMVSS 208 regulations.

• 한국산업융합학회 논문집
• /
• 제27권3호
• /
• pp.573-580
• /
• 2024

Recently, the special alloy, for instance, such as Monel and Inconel, is used for valves, bolt/nuts, and fittings in semiconductor facility, FCEV(fuel cell electric vehicle) and hydrogen gas station, to reduce the hydrogen embrittlement. Even though the Monel material has high cost, it is recommended to use for the cases of ultra high pressure, ultra high leak-proof and so on. The purpose of this study is to investigate the characteristics of Monel material within elastic limit through the comparative analysis when Monel material is extruded or drawn. As the results, the deformation of Monel material was increased as the number of pass was increased, further, the deformation of Monel material by drawing was larger than that by extrusion. In the safety factor, the case that load is less than 420kN, the plastic deformation due to drawing could be happened faster than that due to extrusion. However, the case of more than 420kN, it showed that the plastic deformation for extrusion and drawing was almost similar.

• 수산해양기술연구
• /
• 제54권1호
• /
• pp.25-31
• /
• 2018

In this study, the differences of holding power according to the shape and weight distribution of concrete weight used in shellfish shell fishery were investigated through the experiments. To investigate the differences in shape, five bar-shaped concrete weights with the same length and different cross-sectional shapes were produced. The sectional shape of each weight was square, triangle, circle, small cross, and large cross (SQ, TR, CI, CR-S, CR-L). Ten rectangular parallelepiped weights with different bottom area and cross-sectional area were produced. To investigate the differences by the weight distribution, the holding power on the square model (SQ) with six 50 g weights at different positions was investigated. All the holding power was obtained by measuring the tensile force generated when the concrete weight was pulled at a constant speed on the sand. As a result, there were no differences in holding power between the ten rectangular weights. However, the experiment on weights with different cross-sectional shapes showed differences in holding power. The holding power was higher in the order of CR-L > CR-S > CI > TR > SQ. In the weight distribution test, the holding power was higher as the front side of the weight was heavier. Generally, the frictional force is the same even if the shape is different, when two objects have the same value in the weight and the roughness. On the other hand, it seems to have a large impact when the shape of the bottom is deformed in the course of pulling the object. Particularly, the larger the degree of protrusion like cruciform weights, the more the holding power increased while deeply digging the bottom. It is also likely that the holding power increases as the front weight increases.

• 마이크로전자및패키징학회지
• /
• 제9권3호
• /
• pp.19-23
• /
• 2002

본 논문은 인쇄회로 기판 (PCB)에 내장된 마이크로 플럭스게이트 자기센서 (micro fluxgate magnetic sensor)에 대한 것으로써, 센서의 제작과 폐자로 형성에 따른 자계 검출 특성 변화에 관한 것이다. 이를 위해 연자성 코아를 사각링 형태와 두개의 바 (bar)형태로 각각 구현하였다. 제작을 위해 모두 5층의 기판을 적층하였으며, 가운데 (3번째) 기판을 자성체 코아로, 자성체 코아 외부 (2번째와 4번째) 기판을 여자코일로, 최외부 (1번째와 5번째) 기판을 검출코일로 제작하였다. 연자성 코아로는 약 100,000의 큰 DC 투자율 (permeability)을 갖는 코발트 (Co)가 주성분인 아몰퍼스 재료를 사용하였으며, 여자코일과 검출코일은 구리를 사용하였다. 제작된 자기센서는 여자조건이 360 KHz, $3V_{p-p}$의 구형파일 경우에 사각링 형태의 연자성 코아를 갖는 자기센서에서는 540V/T로 매우 우수한 감도를 보이고 있으며, -100 $\mu$T~＋100 $\mu$T 영역에서 매우 우수한 선형특성을 보이고 있다. 자기 센서의 크기는 $7.3 \times 5.7\textrm{mm}^2$ 이며, 소비전력은 약 8 mW이다. 이런 초소형 자기센서는 휴대용 navigation 시스템, telematics, VR 게임기 등 다양한 응용분야에 적용할 수 있다.

• 천문학논총
• /
• 제27권2호
• /
• pp.29-37
• /
• 2012

In this paper, we study the structure of the Daegyupyo (大圭表, Large Gnomon) of the early Joseon dynasty. A Gyupyo (圭表, Gnomon that is Guibiao as pronounced in Chinese) is composed of a Pyo (表, Biao as pronounced in Chinese) making a shadow and a Gyu (圭, Gui as pronounced in Chinese) measuring its length. It is known that the Daegyupyo with the 40-feet height was constructed between the sixteenth to seventeenth year of the King Sejong reign (1444 - 1445) on the basis of the record of Yuanshi (元史, the History of the Yuan Dynasty). By analyzing historical documents such as Joseonwangjosillok (朝鮮王朝實錄, the Annals of the Joseon Dynasty), Yuanshi, and Jegaryeoksangjip (諸家曆象集, a work written by Sunji Lee), we found a possibility that the Ji (池, a pond) on the Gyu was located in the north side of the Pyo. This structure is different from that in previous studies, but is in a good agreement with that of the 40-feet Guibiao remaining in Dengfeng (登封) of China. Regarding to the Hoengyang (橫梁, cross-bar), we suggest that it was set up by double 5-feet supporting arms apart from the north tip of the Pyo in the radial direction. The 3:4:5 ratio in a rectangular triangle was used to place the Heongyang on the top of the Pyo at a distance of 4-feet (3-feet) in the vertical (horizontal) direction. We also discuss the structural problem when the Hoengyang is positioned apart from the top of the Pyo by supporting arms. In conclusion, we think that this study should be useful in restoring the Daegyupyo of the Joseon dynasty.

• 대한토목학회논문집
• /
• 제3권4호
• /
• pp.1-10
• /
• 1983

평면내력(平面內力)을 받는 철근(鐵筋)콘크리트슬래브, 판(板) 및 쉘 등(等)의 벽부재(壁部材)의 정확한 변형해석(變形解析)을 위하여 균열의 마찰일팽창거동(摩擦一膨脹擧動), 인장증강효과(引張增剛効果) 및 철근의 연결작용(連結作用)을 고려한 실제적인 해석모델을 수립하였다. 본 연구의 이론(理論)에 입각한 전산(電算)프로그램을 작성(作成)하여 포괄적인 변형해석이 수행되었으며, 새로운 개념의 마찰평형설계(摩擦平衡設計)와 종래(從來)의 무마찰평형설계(無摩擦平衡設計)에 입각한 철근설계에 대하여 각각 균열폭을 계산하여 비교하였다. 마찰설계개념에 의해 철근을 설계했을 경우 종래의 무마찰설계보다 변형량이 상당히 감소됨을 발견하였다. 또한, 철근직경과 균열간격이 균열폭에 미치는 영향을 연구(硏究)하였다. 본(本) 연구(硏究)에서 개발된 해석모델로 철근콘크리트부재(部材)의 좀 더 실제적이고 정확한 변형해석(變形解析)을 할 수 있게 되었다.

• Korea-Australia Rheology Journal
• /
• 제19권4호
• /
• pp.233-242
• /
• 2007

We performed a numerical investigation to find out the optimal choice of the spatial discretization in the distributed-Lagrangian-multiplier/fictitious-domain (DLM/FD) method for the solid/fluid interaction problem. The elastic solid bar attached on the bottom in a pressure-driven channel flow of a Newtonian fluid was selected as a model problem. Our formulation is based on the scheme of Yu (2005) for the interaction between flexible bodies and fluid. A fixed regular rectangular discretization was applied for the description of solid and fluid domain by using the fictitious domain concept. The hydrodynamic interaction between solid and fluid was treated implicitly by the distributed Lagrangian multiplier method. Considering a simplified problem of the Stokes flow and the linearized elasticity, two numerical factors were investigated to clarify their effects and to find the optimum condition: the distribution of Lagrangian multipliers and the solid/fluid interfacial condition. The robustness of this method was verified through the mesh convergence and a pseudo-time step test. We found that the fluid stress in a fictitious solid domain can be neglected and that the Lagrangian multipliers are better to be applied on the entire solid domain. These results will be used to extend our study to systems of elastic particle in the Stokes flow, and of particles in the viscoelastic fluid.

• Journal of the Korean Wood Science and Technology
• /
• 제13권3호
• /
• pp.34-40
• /
• 1985

The characteristics of Paulownia coreana wood used for sounding boards has been revealed through this study. The 80 specimens were selected from Paulownia coreana wood. The dynamic Young's modulus, the internal friction and resonant frequency of wood were measured by the method of making a rectangular bar resonate in the audio frequency range. The results obtained are summarized as follows: 1. The average values of the specific gravity, the dynamic Young's modulus and the internal friction concerning Paulownia coreana used for sounding boards are $0.252{\pm}0.022$, $(0.494{\pm}0.068){\times}10^{11}$ dyne/cm and $(7.89{\pm}1.692){\times}10^{-3}$ respectively. 2. The average values of resonant frequency, the velosity of sound, and K values are $504{\pm}24.298$ Hz, $5018{\pm}219.83$m/s, and $(9.907{\pm}2.05){\times}10^{-4}$ respectively. 3. The dynamic Young's modulus of Paulownia coreana increases with the increase of the specific gravity, and that on the contrary the internal friction decreases. 4. The dynamic Young's modulus was abruptly decreased as the moisture content of wood specimens was increased up to the fiber saturation point, and the internal friction was linearly increased as the moisture content of wood specimens were increased. 5. The vibration properties of Paulownia coreana are that the dynamic Young's modulus is fairly high, the internal friction is low, and the ratio of Young's modulus to specific gravity shows large value.

• 한국지진공학회논문집
• /
• 제14권2호
• /
• pp.27-36
• /
• 2010

횡하중을 받는 RC 기둥의 전단강도는 기둥의 변위연성도가 증가함에 따라 감소하는 것으로 알려져 있다. 연성도의 증가에 따른 전단강도의 감소율은 초기전단강도에 따라 크게 좌우되므로 이를 합리적으로 예측하기 위해서는 초기전단강도의 평가가 매우 중요하다. 기둥의 전단거동은 단면모양, 형상비, 축력, 축방향철근비, 연성도 등 다양한 요인에 의하여 영향을 받아 복잡하다. 본 연구에서는 형상비, 단면의 중공비, 축방향철근비, 중공 및 중실단면을 변수로 하는 시험체를 제작하여 실험적 연구를 수행하여 전단거동특성을 살펴보았다. 또한, 축방향철근이 전단강도에 미치는 영향을 분석하여 형상비와 축력을 고려한 기존의 초기전단평가식을 보완하였으며, 그 타당성을 검증하였다.