• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2011.10a
• /
• pp.39-41
• /
• 2011

The recycling rate of recovered paper in Korea is the highest in the world, 92%, but remanufacturing yield is low due to the extremely poor quality of the paper. The poor quality, in turn, influences to the reject amount in deinking process. To increase the yield of old newspaper recycling process, hydrophobic degree of inorganic pigments of deinking stock must be reduced. To determine the hydrophobicity, Pitch Potential Deposit Tester (PDT) was newly designed and applied with respect to the SB latex property of various quality used in Korea; its hydrophobic degree according to Tg, gel content, charge and particle size of latex and optimum designing condition of SB latex. And below are the conclusions: 1. The reason of excessive reject from old newspaper deinking process for total amount of printed ink is loss of inorganic pigments. When lipase, a biochemical catalyst, was applied with the purpose of preventing inorganic pigments loss about more than 70% of total reject weight and promoting hydration of pulp for deinking, deinking process yield of pre flotation secondary stage increased remarkably without any changes of deinking efficiency. 2. Lipase improved deinking stock by cutting ester linkage on surface of hydrophobic materials to promote its hydration. From this, it reached the conclusion that hydration degree of stock exercises significant effect on flotation deinking process yield. 3. Inorganic alkali promotes hydration of deinking stock. But there have been needs for more fundamental measures other than inorganic alkali of promoting hydration for yield improvement. For this, this study intended to find out reasons of chemical properties change on surface of hydrophobic material by change of pH. 4. Pitch Deposit Test (PDT) was performed for understanding principle of why surface of coating flake from OMG is hydrophobic and why it becomes hydrophilic when pH of stock is alkaline. As a result of this test, it is determined that swelling property by change of pH of latex film, which were used as coating adhesive is the reason for hydrophobic change. 5. Hydrophilicity of coating flake increased with hydrophilic pigments. And as more of SB Latex adhesive was used and higher of calcium hardness of stock became, its hydrophilicity decreased. SB Latex adhesive film is reformed by mechanical friction. For having hydrophilicity under neutral pH, strong bruising action such as kneading is required. 6. Because swelling of adhesive film decreases as Tg of SB latex gets lower and mean diameter gets smaller, it shows hydrophobicity under neutral pH. This lowers hydrophilicity of coating flake, which leads to easy elimination with flotation reject on DIP process. Therefore, for improving future flotation yield, it is necessary to develop to use eco-friendly clean SB latex by raising Tg and increasing mean diameter for recycling, and as a result, to reduce excessive loss of coating flake as a reject from deinking process.

• Membrane Journal
• /
• v.28 no.3
• /
• pp.157-168
• /
• 2018

Potassium tannate (TA-K), which is prepared by base treatment of the bio-renewable tannic acid (TA), was evaluated for its potential application as a draw solute for water purification by forward osmosis. The forward osmosis and recovery properties of TA-K were systematically investigated. In the application of forward osmosis through the active layer facing feed solution (AL-FS) method, the water flux of TA-K draw solution was significantly higher than that of the TA draw solution, while that of the latter was not identified. At a low concentration of 100 mM, the osmotic pressure (1,135 mOsmol/kg) of the TA-K draw solution was approximately 6.5 times that (173 mOsmol/kg) of the NaCl draw solution. Furthermore, the water flux and specific salt flux (6.14 LMH, 1.26 g/L) of the TA-K draw solution at 100 mM were approximately 2.5 and 0.5 times those of the NaCl draw solution (2.46 LMH, 2.63 g/L) at the same concentration, respectively. For reuse, TA-K was precipitated by using a metal ion and recovered through membrane filtration. This study demonstrates the applicability of a phytochemical material as a draw solute for forward osmosis.

• Clean Technology
• /
• v.26 no.2
• /
• pp.116-121
• /
• 2020

In this paper, the recycling of waste Ni-MH battery by-products for electric vehicle is studied. Although rare earths elements still exist in waste Ni-MH battery by-products, they are not valuable as materials in the form of by-products (such as an insoluble substance). This study investigates the recovering of rare earth oxide for solvent extraction A/O ratio, substitution reaction, and reaction temperature, and scrubbing of the rare earth elements for high purity separation. The by-product (in the form of rare earth elements insoluble powder) is converted into hydroxide form using 30% sodium hydroxide solution. The remaining impurities are purified using the difference in solubility of oxalic acid. Subsequently, Yttrium is isolated by means of D2EHPA (Di-[2-ethylhexyl] phosphoric acid). After cerium is separated using potassium permanganate, lanthanum and neodymium are separated using PC88A (2-ethylhexylphosphonic acid mono-2-ethylhexyl ester) and it is calcinated at a temperature of 800 ℃. As a result of the physical and chemical measurement of the calcined lanthanum and neodymium powder, it is confirmed that the powder is a microsized porous powder in an oxide form of 99.9% or more. Rare earth oxides are recovered from Ni-MH battery by-products through two solvent extraction processes and one oxidation process. This study has regenerated lanthanum and neodymium oxide as a useful material.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.6
• /
• pp.1677-1685
• /
• 2014

Short discrete fibers compounded with concrete can enhance the tensile resistance and ductility of concrete. Recently, the effectiveness of the reinforcement has increased according to the increasing length of steel fiber. However, the lengthening of steel fiber requires reducing the ratio of the fiber content to remain the workability and quality of concrete. Thus, the present study evaluated the flexural performance of fiber reinforced concrete with less than l.0% fiber volume ratios of steel fiber, 30mm and 60mm long, and polypropylene fiber, being evaluated as a good reinforcing material with chemical stability, long-term durability, and cost effectiveness. Concrete with more than 0.25% steel and 0.5% polypropylene fibers improved the brittle failure of concrete after reaching cracking strength. Concrete reinforced with polypropylene exhibited deflection-softening behavior, but that with more than 0.5% polypropylene delayed stress reduction and recovered flexural strength by 60 to 80% after cracking strength. In conclusion, concrete reinforced with more than 0.75% polypropylene could improve structural flexural performance. In particular, energy absorption capacity of reinforced concrete with 1.0% polypropylene fiber was similar to that with 0.5% and 0.7% steel fibers.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.15 no.3
• /
• pp.286-293
• /
• 1986

The purpose of this study was to investigate the effect of withering on mechanical properties for optimizing the condition of transportation and storage of fresh leafy vegetables which they would be easily able to be suffered the physical damage. Experimental material used were spinaches and leeks which were easily apt to be withered. The breaking stress, elastic modulus and viscosity were measured in the range of temperature $3{\sim}37^{\circ}C$ and water content $70{\sim}95%$ by the four element model, being used the creep tester made by author. As a result of this study, while water content was decreased, breaking stress was increased. The elastic modulus and viscosity of the specimens were not influenced on temperature, but on water content. In reversibility test of the withering, the appearance, water content and elastic modulus of the specimens were completely recovered to the initial freshness, but the viscosity was not.

• Resources Recycling
• /
• v.16 no.5
• /
• pp.8-12
• /
• 2007

Anhydrous magnesium chloride, dehydration product from magnesium chloride hydrate is a general raw material to prepare electrolytic magnesium. However, the dehydration is not trivial and can be accompanied by hydrolysis leading to the production of undesirable hydroxy chloride compounds of magnesium. Therefore, dehydration process is actually the most complicated and hardest in the electrolysis methods for the production of magnesium. In this work, the influence of dehydrating temperature has been studied at the temperature range from $200^{\circ}C$ to $600^{\circ}C$ in air and HCl gas atmosphere individually to compare the results. With increasing of dehydration temperature MgOHCl and MgO were obtained in air. On the other hand, when the temperature was increased above $300^{\circ}C$ anhydrous magnesium chlorides were prepared in HCl gas atmosphere. Anhydrous magnesium chloride was formed at near $300^{\circ}C$ and completely crystallized at about $500^{\circ}C$. All of the HCl used as atmosphere gas in the dehydration was recovered as hydrochloric acid solution at a water vessel up to 41% by weight at $20^{\circ}C$.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.25 no.1
• /
• pp.209-224
• /
• 1998

The purpose of this study was to compare the amount of calcium fluoride deposited on the enamel and dentin surface and to obtain information on the morphological change and crystallographic details of mineral deposition after 12,000ppm APF application in vitro. The bovine enamel and dentin blocks were randomly assigned to eight groups according to artificial caries lesion formation and difference of fluoride application time. The fluoride concentration and morphological characteristics on the treated enamel and dentin surface were investigated by using fluoride quantitative analysis and SEM. The powdered enamel and dentin of the intact bovine incisors were prepared for the X-ray diffraction analysis. The following results were obtained. 1. The amounts of KOH-soluble fluoride on the carious enamel and dentin surface after 24h APF application were higher than after only 5min APF application(p<0.05), but in the case of the sound enamel and dentin surface were similar after 5min and 24h application (P>0.05). The fluoride content was highly increased in the carious dentin as compared with sound dentin after APF application(P<0.05). 2. The carious enamel surface after APF application, the demineralized enamel surface were recovered a more dense enamel surface and precipitation of crystal was observed a distintive surface layer of spherical globules of about 1 m diameter. In the case of the fluorided carious dentin surface, precipitation of calcium fluoride-like material was deposited both inside the dentinal tubules as well as in the intertubular regions. 3. The crystallographic structure of powdered enamel and dentin after 24h APF application had large crystallities of apatite and CaF2 diffraction peaks in the enamel as compared with dentin. The diffraction data collected from the 27.50-29.50(2) angular range of the powdered enamel, the (105) apatite, (225) apatite and (111) CaF2 peaks of the enamel crystallities were detected after 24h APF application.

• Preventive Nutrition and Food Science
• /
• v.8 no.1
• /
• pp.46-53
• /
• 2003

The current study investigated the effect of Korean safflower (Carthamus tinctorius L.) seed powder and its water and ethanol extracts on bone metabolism during recovery from rib-fracture induced by surgical operation in rats. 10-week-old male Sprague-Dawley rats weighing about 320 g were divided into 9 groups after arrival: 10d control (AIN 76 semi-purified diet), 10d safflower seed powder (10d SS-powder), 10d safflower seed ethanol extract (10d SS-EtOH), 10d safflower seed water extract (10d SS-$H_2O$), 20d control (AIN-76 semi-purified diet), 20d safflower heed powder (20d SS-powder), 20d safflower seed ethanol extract (20d SS-EtOH), 20d safflower seed water extract (20d SS-$H_2O$), and 20d sham-operation (20d sham), The dietary level for all the supplements was 5% based on the raw material weight. The rats were fed the experimental diets for 10 days before the rib fracture operation and for a further 10 or 20 days after the operation. A number 9 rib was fractured surgically and a sham-operation also performed. The rats were then sacrificed on the l0th or 20th day after the operation. The body weight initially decreased after the operation in all the rib-fractured groups, then gradually recovered. The concentrations of plasma osteocalcin were higher in the control group than in all the safflower-supplemented groups 10 and 20 days after the rib-fracture (p < 0.05). The bone-specific ALP (alkaline phosphatase) activity was significantly higher in the SS-EtOH group than in the other groups 20 days after the rib-fracture (p < 0.05). The level of urinary DPD (deoxypridinoline) was significantly higher in the SS-EtOH and SS-$H_2O$ groups than in the other groups 10 days after the rib-fracture. When comparing the PTH (parathyroid hormone) and calcitonin levels, the SS-$H_2O$ group exhibited the highest PTH level among the groups 10 and 20 days after the rib-fracture. Thus, it was concluded that the bone turnover during the fracture-healing period was more rapid in the rats supplemented with safflower seed powder or its fractions than in the control rats. Furthermore, the SS-$H_2O$ fraction was identified as the most effective in stimulating bone remodeling, as bone resorption and bone formation were both significantly increased during fracture healing when compared to the control group.

• KSBB Journal
• /
• v.27 no.1
• /
• pp.67-74
• /
• 2012

In this study, the optimum conditions of fermentation were determined by isolating the microorganisms with the ability to bioconvert the Citrus peel flavonoid, and the effect of the fermented Citrus peel extract which was bioconverted on the oxidative damage of HIT-T15 cell was investigated. The Aureobasidium pullulans Y-12 was isolated and identified with the strains having bioconversion activity. The fermentation conditions for bioconversion activity were confirmed to be optimal when culturing for three days at $25^{\circ}C$, 150 rpm in a culture medium containing 5% Citrus peel power and 0.8% casitone. As a result of bioconversion, 32.8 mg/g and 21.5 mg/g of naringenin and hesperetin, which were aglycone flavones, were produced respectively. Also in the flavonoid content, it was confirmed that FCP produced 154.8 mg/g while CP produced 33.7 mg/g, thus producing more by approximately 4.6 times. As a result of treating FCP and CP after inducing the oxidative damage for HIT-T15 cell by treating the deoxy-D-ribose with $IC_{50}$ (38 mM) concentration, the surviving rate was recovered to 90% for FCP treatments in the 0.01 mg/mL concentration and for CP treatments in the 0.025 mg/mL concentration. Also in the insulin secretion rate, FCP treatments increased by 206% and CP treatments by 132% when treated in the 0.1 mg/mL concentration. As the bioconverted FCP can inhibit the oxidative damage of HIT-T15 cell in the low concentration, it was considered its usability as the functional material for prevention of the type 2 diabetes.

• Resources Recycling
• /
• v.19 no.6
• /
• pp.51-60
• /
• 2010

A study on the recovery of cobalt and lithium from Lithium Ion Battery(LIB) scraps has been carried out by a physical treatment - leaching - solvent extraction process. The cathode scraps of LIB in production were used as a material of this experiment. The best condition for recovering cobalt from the anode scraps was acquired in each process. The cathode scraps are dissolved in 2M sulfuric acid solution with hydrogen peroxide at $95^{\circ}C$, 700 rpm. The cobalt is concentrated from the leaching solution by means of a solvent extraction circuit with bis(2-ethylhexyl) phosphoric acid(D2EHPA) and PC88A in kerosene, and then cobalt and lithium are recovered as cobalt hydroxide and lithium carbonate by precipitation technology. The purity of cobalt oxide powder was over 99.98% and the average particle size after milling was about 10 lim. The over all recoveries are over 95% for cobalt and lithium. The pilot test of mechanical separation was carried out for the recovery of cobalt from the scraps. The $Co_3O_4$ powder was made by the heat treatment of $Co(OH)_2$ and the average particle size was about 10 ${\mu}m$ after grinding. The recovery was over 99% for cobalt and lithium each other and the purity of cobalt oxide was over 99.98%.