• Fire Science and Engineering
• /
• v.30 no.2
• /
• pp.75-80
• /
• 2016

In the wake of expanding and overpopulating urban areas, traffic congestion has been worsening increasingly, causing huge economic losses. In a bid to effectively use the space of metropolitan areas, the construction and operation of a double deck tunnel has been on the rise. On the other hand, a lower height of a double deck tunnel is expected to generate more smoke and soot in a fire than other usual tunnels. Therefore, it is undesirable to apply the standard for fire intensity or smoke generation, which were designed for existing road tunnels. A part of an effort to propose a design fire curve that is useful for double deck tunnel, is intended to obtain and analyze the fire characteristics in a double deck tunnel through a real scale fire test. The test was conducted according to the fire scenario with one passenger car and two passenger cars; the monitored fire intensity was a maximum of 2.4 MW and 3.5 MW, respectively.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.28 no.2
• /
• pp.18-27
• /
• 2000

The importance of constraints has been one of major issues in recreation for prediction of choice behavior; however, traditional conjoint choice model did not consider the effects of these variables or fail to integrate them into choice model adequately. The purposes of this research are (a) to estimate the effects of constraints in theme park choice behavior by the constraints-induced conjoint choice model, and (b) to test additional explanatory power of the additional constraints in this suggested model against the more parsimonious traditional model. A leading polling agency was employed to select respondents. Both alternative generating and choice set generating fractional factorial design were conducted to meet the necessary and sufficient conditions for calibration of the constraints-induced conjoint choice model. Th alternative-specific model was calibrated. The log-likelihood ratio test revealed that suggested model was accepted in the favor of the traditional model, and the goodness-of-fit($\rho$$^2$) of suggested and traditional model was 0.48427 and 0.47950, respectively. There was no difference between traditional and suggested model in estimates of attribute levels of car and shuttle bus because alternatives were created to estimate the effects of constraints independently from mode related variables. Most parameters values of constraints had the expected sign and magnitude: the results reflected the characteristics of the theme parks, such as abundance of natural attractions and poor accessibility in Everland, location of major fun rides indoor in Lotte World, city park like characteristics of Dream Land, and traffic jams in Seoul. Instead of the multinomial logit model, the nested logit model is recommended for future researches because this model more reasonably reflects the real decision-making process in park choice. Development of new methodology too integrate this hierarchical decision-making into choice model is anticipated.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.1
• /
• pp.128-136
• /
• 2003

In today's design trend of vehicle structure, crush zone is fiequently reinforced by adding a box-shaped sub-frame in order to avoid an excessive deformation against a high-speed offset barrier such as EU Directive 96/97 EC, IIHS offset test. That kind of vehicle structure design results in a relatively monotonic crash pulse for airbag ECU(Electronic Control Unit) located at non-crush zone. As for an angular crash event, the measured crash signal using a single-axis accelerometer in a longitudinal direction is usually weaker than that of frontal barrier crash. Therefore, it is not so easy task to achieve a satisfactory crash discrimination performance for offset and angular crash events. In this paper, we introduce a new crash discrimination algorithm using an electronic X-Y 2-axis accelerometer in order to improve crash discrimination performance especially for those crash events. The proposed method uses a crash signal in lateral direction(Y-axis) as well as in longitudinal direction(X-axis). A crash severity measure obtained from Y-axis acceleration is used to improve the discrimination between fire and no-fire events. The result obtained by the proposed measure is logically ORed with an existing algorithm block using X-axis crash signal. Simulation and pulse injection test have been conducted to verify the performance of proposed algorithm by using real crash data of a 2,000cc passenger vehicle.

• International Journal of Automotive Technology
• /
• v.8 no.2
• /
• pp.203-209
• /
• 2007

As the vehicle electronic control technology quickly grows and becomes more sophisticated, a more efficient means than the traditional in-vehicle driving test is required for the design, testing, and tuning of electronic control units (ECU). For this purpose, the hardware-in-the-loop simulation (HILS) scheme is very promising, since significant portions of actual driving test procedures can be replaced by HIL simulation. The HILS incorporates hardware components in the numerical simulation environment, and this yields results with better credibility than pure numerical simulations can offer. In this study, a HILS system has been developed for ESP (Electronic Stability Program) ECUs. The system consists of the hardware component, which that includes the hydraulic brake mechanism and an ESP ECU, the software component, which virtually implements vehicle dynamics with visualization, and the interface component, which links these two parts together. The validity of HIL simulation is largely contingent upon the accuracy of the vehicle model. To account for this, the HILS system in this research used the commercial software CarSim to generate a detailed full vehicle model, and its parameters were set by using design data, SPMD (Suspension Parameter Measurement Device) data, and data from actual vehicle tests. Using the developed HILS system, performance of a commercial ESP ECU was evaluated for a virtual vehicle under various driving conditions. This HILS system, with its reliability, will be used in various applications that include durability testing, benchmarking and comparison of commercial ECUs, and detection of fault and malfunction of ESP ECUs.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.05a
• /
• pp.343-346
• /
• 2012

Today, According to it widely used that third generation mobile networks service, WCDMA module development technology and its utilization is expanding increasingly and thus to IT Convergence industries is a trend that a lot of appears. This paper, OBD-II communications to bring a vehicle information use and data to an external server transfer and it was developed that vehicle status monitoring from other external devices can be system. From the various sensors inside a vehicle using the OBD-II connector read the information, after converting the user easier to see, WCDMA module using the car status monitoring system to transfer to an external data server was implemented. Developed to test the performance of the system using virtual's state vehicle simulator, which occurs in the real car that will generate the data. It was sent to the OBD-II connector to be occurred data, vehicle status monitoring system was confirmed that Data was received without error. In addition, When this data using WCDMA transmit data to an external server the same data was confirmed that it was received without error. In the future, this technology using the OBD-II vehicle IT convergence technology can be used in a wide range.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.10
• /
• pp.739-744
• /
• 2017

Elastic deformation and fatigue damage can cause the permanent deformation of a kart's frame during turning, affecting the kart's driving performance. A kart's frame does not contain any suspension or differential devices and, therefore, the dynamic behavior caused by torsional deformation when driving along a curve can strongly affect these two kinds of deformations. To analyze the dynamic behavior of a kart along a curved section, the GPS trajectory of the kart is obtained and the torsional stress acting on the kart-frame is measured in real time. The mechanical properties of leisure and racing karts are investigated by analyzing their material properties and conducting a tensile test. The torsional stress concentration and frame distortion are investigated through a stress analysis of the frame on the basis of the obtained results. Leisure and racing karts are tested in each driving condition using driving analysis equipment. The behavior of a kart when being driven along a curved section is investigated through this test. Because load movement occurs owing to centrifugal force when driving along a curve, torsional stress acts on the kart's steel frame. In the case of a leisure kart, the maximum torsional stress derived from the torsional fatigue limit was found to be 230 MPa, and the torsional fatigue limit coefficient was 0.65 when driving at a speed of 40 km/h. Furthermore, the driving elements during the cornering of a kart were measured based on an actual auto-test after installing a driving measurement system, and the driving behavior of the kart was analyzed by measuring its vertical displacement.

• International Journal of Automotive Technology
• /
• v.8 no.3
• /
• pp.259-268
• /
• 2007

A knock detection circuit that is based on the signal of an accelerometer installed on the engine block of a spark ignition automotive engine has a band-pass filter with a certain frequency as a parameter to be calibrated. A new statistical method for the determination of the frequency which is the most suitable for the knock detection in real-time applications is proposed. The method uses both the cylinder pressure and block vibration signals and is divided into two steps. In both steps, a new recursive trigonometric interpolation method that calculates the frequency contents of the signals is applied. The new trigonometric interpolation method developed in this paper improves the performance of the Discrete Fourier Transformation, allowing a flexible choice of the size of the moving window. In the first step, the frequency contents of the cylinder pressure signal are calculated. The knock is detected in the cylinder of the engine cycle for which at least one value of the maximal amplitudes calculated via the trigonometric interpolation method exceeds a threshold value indicating a considerable amount of oscillations in the pressure signal; this cycle is selected as a knocking cycle. In the second step, the frequency analysis is performed on the block vibration signal for the cycles selected in the previous step. The knock detectability, which is an individual cylinder attribute at a certain frequency, is verified via a statistical hypothesis test for testing the equality of two mean values, i.e. mean values of the amplitudes for knocking and non-knocking cycles. Signal-to-noise ratio is associated in this paper with the value of t-statistic. The frequency with the largest signal-to-noise ratio (the value of t-statistic) is chosen for implementation in the engine knock detection circuit.

• Journal of IKEEE
• /
• v.19 no.3
• /
• pp.400-406
• /
• 2015

In this paper, we designed a decision feedback based diversity modem hardware architecture for IEEE802.11p WAVE and tested the modem on the road with car attached shark antenna. One of the dual channel modem and the diversity single modem with maximum ratio combining algorithm can be selected on the designed architecture. The designed modem have been implemented on the Xillinx Kintex7 FPGA. We tested the modem performance on the smart highway experience road. As experimental results, we can verify the performance of the diversity modem on real road and the enlarged communication range by more than 100%.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.8
• /
• pp.1615-1622
• /
• 2016

This research aims to develop a voyage performance monitoring system based on international standards. The developed system is equipped with an electronic navigational chart(ENC) that provides onshore and offshore information, as well as supports standardized interfaces with navigational equipment, such as a gyro compass, a differential global positioning system(DGPS), and an automatic identification system(AIS), to monitor the navigation route in real time. In addition, the proposed system adopts a car navigation system to provide a graphical user interface, an intuitive menu-driven configuration, and an easy guide for safer sea navigation. The system, interfaced with the gyro compass and DGPS, was verified without any data loss, and passed a test conducted under extreme conditions by the Korea Laboratory Accreditation Scheme(KOLAS). Finally, the system contributes to preventing collision of vessels and minimizing casualties by maximizing the convenience of mariners which a conventional system does not provide.

• Tribology and Lubricants
• /
• v.30 no.2
• /
• pp.124-129
• /
• 2014

The piping system accounts for a large portion of the machinery structure of a plant, and is considered as a very important mechanical structure for plant safety. Accordingly, it is used in most energy plants in the nuclear, gas, and heavy chemical industries. In particular, the piping system for a nuclear plant is generally complicated and uses the reactor and its cooling system. The piping equipment is exposed to diverse loads such as weight, temperature, pressure, and seismic load from pipes and fluids, and is used to transfer steam, oil, and gas. In ultrasound infrared thermography, which is an active thermography technology, a 15-100 kHz ultrasound wave is applied to the subject, and the resulting heat from the defective parts is measured using a thermography camera. Because this technique can inspect a large area simultaneously and detect defects such as cracks and delamination in real time, it is used to detect defects in the new and renewable energy, car, and aerospace industries, and recently, in piping defect detection. In this study, ultrasound infrared thermography is used to detect information for the diagnosis of nuclear equipment and structures. Test specimens are prepared with piping materials for nuclear plants, and the optimally designed ultrasound horn and ultrasound vibration system is used to determine damages on nuclear plant piping and detect defects. Additionally, the detected images are used to improve the reliability of the surface and internal defect detection for nuclear piping materials, and their field applicability and reliability is verified.