• Advances in materials Research
• /
• v.7 no.2
• /
• pp.149-162
• /
• 2018

Following our previous work, we have conducted further systematic studies to investigate the effects of reactive blending on the thermal and mechanical properties of blends of poly(lactic acid) (PLA) and a liquid rubber, polybutadiene (LPB). The toughened PLAs were prepared by melt-blending the PLA with various contents (0-9 wt.%) of the LPB in the absence or presence of dicumyl peroxide (DCP), a radical initiator. It was found that the rubber domains were homogeneously dispersed at the nanoscale in the PLA matrix up to 9 wt.% of LPB thanks to the reactive blending in the presence of DCP. Owing to the compatibilization of PLA with LPB through reactive blending, the elongation and toughness of PLA was enhanced, while the hydrolytic degradation of PLA was reduced.

• 한국연소학회:학술대회논문집
• /
• 2012.11a
• /
• pp.39-41
• /
• 2012

The influence of coal blending methods such as out-furnace (external or pre-mixed) blending and in-furnace (initially non-mixed) blending with different excess oxygen (highest, medium, and lowest stoichiometric conditions) on unburned carbon and NOx emissions of blend combustion in an entrained flow reactor (EFR) has been analyzed, using experimental and numerical approaches for binary coals used by Korean power plants. The results confirm that under the medium condition, contrasting processes such as reactive and un-reactive effects occur with SBRs in the out-furnace blending method. The in-furnace blending method results in an improvement in the efficiency of unburned carbon fractions and a further reduction in the NOx emission. Under the highest condition, the unburned carbon fraction in both the out-furnace and the in-furnace blending methods corresponds with the tendency under the medium condition with contrasting processes of lower magnitude, whereas the NOx emission in the highest condition increases slightly. Under the lowest conditions, the unburned carbon fraction in the out-furnace blending method gradually decreases as SBR decreases, without a competition effect. The reduction of NOx emission under the lowest conditions is more effective than those under other conditions for the two blending methods because of a homogeneous and heterogeneous NOx reduction mechanism.

• Polymer(Korea)
• /
• v.30 no.2
• /
• pp.118-123
• /
• 2006

The effect of transesterification on the rheological properties in the melt reactive blending of poly(butylene terephthalate)(PBT) with poly(ethylene terephthalate)(PET) has been studied. The melt viscosity depression in PBT was found in PBT/PET blends due to the intrinsic low melt viscosity of PET compared to PBT. In addition, the thermal degradation in the melt blending and transesterification between two polyesters were considered as other factors fer the lowering of the melt viscosity in the blends. In the PBT/PET blends, calcium stearate was less effective than in PBT as a lubricant, however it accelerated both the thermal degradation and transesterification during melt blending. As a result, further melt viscosity drop was obtained in the reactive melt blending of PBT/PET.

• Nuclear Engineering and Technology
• /
• v.56 no.9
• /
• pp.3942-3949
• /
• 2024

This study focuses on investigating the chemical degradation characteristics of cementitious barriers used in low-and intermediate-level radioactive waste repository by reactive transport modeling. The impact of the blending with supplementary cementitious materials (SCMs) in the barriers on the chemical degradation was evaluated to find the optimum barrier design. A number of different barrier designs were examined by replacing ordinary Portland cement (OPC) by SCMs (i.e., fly ash, silica fume, and blast-furnace slag). The simulation results showed that silica fume blended barrier has better durability against chemical degradation by rainwater compared to fly ash or blast-furnace slag blended barriers. In addition, the chemical durability of silica fume-based barrier increased with increasing replacement level up to about 20 %. It seems that the amount of formed calcium silicate hydrate (CSH) in the initial cement-based barrier highly affects the overall chemical durability. The newly developed reactive transport model demonstrated its capability for understanding the barrier performance and investigating the optimal design of the barrier system.

• Elastomers and Composites
• /
• v.48 no.4
• /
• pp.249-255
• /
• 2013

Hydroxypropyl terminated PDMS was synthesized by the hydrosilylation reaction with allyl alcohol in the presence of Karstedt's catalyst. And them, an one-pot reaction with HDI isocyanurate trimer and hydroxyethyl methacrylate was conducted to give a silicone-modified urethane acrylate oligomer (PUA oligomer) having 9000 g/mol, weight average molecular weight. The synthesized PUA oligomer was characterized by using FT-IR and GPC. The UV-curable coatings were prepared by PUA oligomer blending with a reactive monomer (phenylthioethyl acrylate) under the different mole ratios. It was found that the refractive index of cured film increased when the reactive monomer was added but there was no relationship between the refractive index and amount of reactive monomer. Also, their transmittance for cured films was not change as increasing the content of reactive monomer.

• Elastomers and Composites
• /
• v.50 no.3
• /
• pp.189-195
• /
• 2015

In this study, we prepared epoxidized poly ethylene-ter-1-decene-ter-divinylbenzene (Epo-PEHV) as a reactive compatibilizer to prevent phase separation phenomenon which occurs upon blending polypropylene (PP) and ethylene-vinyl alcohol copolymer (EVOH). Firstly, PEHV was prepared under high catalyst activity according to content of catalyst and cocatalyst. After then, we modified vinyl group of the terpolymer with epoxy group. We observed that the terpolymer was successfully epoxidized by 1H-NMR and FT-IR analysis. The Epo-PEHV was added by 2, 5, 10% in PP/EVOH blends. The morphologies and mechanical properties of PP/Epo-PEHV/EVOH blends were analyzed by SEM and UTM, respectively. Epo-PEHV enhanced the interfacial adhesion of PP and EVOH blends.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.260-260
• /
• 2006

Sericin was modified by solution blending (10-30 wt%) with 70-90 wt% polyacrylamide (PAM) in water. The reactive sites of sericin such as serine and tyrosine were attached to PAM. Proton Nuclear Magnetic Resonance ($^{1}H-NMR$) and thermogravimetric analysis were used to characterize the modified sericin. The electrospinning conditions i.e. the blend composition and the power supply voltage, at a tip to target distance of 15 cm were studied. The morphology of nanoparticles and nanofibers was observed by scanning electron microscopy. The average particles size of the nanoparticle obtained was 191 nm and nanofibers was 150-300 nm.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.1082-1082
• /
• 2001

Extrusion is one of the most important processes in polymer industry. The characterization of the polymer melt during processing will improve this process noticeably, One possibility of characterizing the actual processed polymer melt is the inline near infrared (NIR) spectroscopy, With this method several polymer properties can be observed during processing, e.g. composition, moisture ormechanical properties of the melt. For this purpose probes for transmission and reflection measurements have been developed, withstanding the high temperatures and pressures appearing during extrusion process (tested up to 300$^{\circ}C$ and 10 ㎫). For the transmission system an optical bypass was developed to eliminate disturbing spectral influences and hence increase the long term stability, which is the prerequisite for an industrial application. Measurements in transmission and reflection produced comparable results (or blending processes, where the prediction error was less than 1%. An optimum RMSEP of only 0.24% was found for preprocessed polymer blends measured in transmission on a laboratory extruder. A transflection measurement allowed for the first time the recording of relevant NIR-spectra in the screw area of an extruder. The application to a (PE+PP) blending process delivered promising results. This new measurement mode allows the observation of the ongoing processes within the screw area, which is of maximum Interest for reactive extrusion processes. Due to economic reasons the calibration transfer between different extrusion systems is also of high importance. Investigations on simulated and real-world spectra showed that a calibration transfer is possible. A new method alternatively to the well-known direct standardization procedures was developed, which is based on an automatic data pretreatment. This procedure delivers comparable results for the calibration transfer. Overall this paper presents concepts, components and algorithms for the inline near infrared (NIR) spectroscopy for polymer extrusion, which allows the use of it in a real industrial extrusion process.

• Clean Technology
• /
• v.15 no.3
• /
• pp.180-185
• /
• 2009

The ethylene-propylene rubber (EPDM) scrap generated from automobile weatherstrip manufacturing process was used to make a thermoplastic elastomer through blending with polypropylene. The surface activated EPDM powder was obtained by the high temperature and shear pulverizer. The addition of surfactant resulted in more surface activated EPDM powder and the optimum loading amounts of surfactant was 1.5 phr. Maleic anhydride was grafted onto polypropylene by reactive blending to give functionalized polypropylene. The wetting property between EPDM scrap and polypropylene was improved by the addition of poly (ethylene-co-acrylic acid) as a compatibilizing agent. Poly(ethylene-co-acrylic acid) decreased the surface tension of polypropylene and thus would contribute to the wettability with EPDM powder.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.52 no.4
• /
• pp.93-101
• /
• 2010

The purpose of this study is to provide basic data for utilization in environment-friendly and economically outstanding CSG construction method by physical and mechanical properties of CSG materials including characteristics of uniaxial compressive strength, microscopic structure and freezing and thawing resistance in accordance with the cement content and curing time of the cement, and size of specimen. In this study, specimens with cement content of 4, 6, 8 and 10% of the total weight were, and, in order to examine the characteristics of the sizes of specimen, specimens with ${\Phi}50{\times}100mm$, ${\Phi}100{\times}200mm$ and ${\Phi}150{\times}300mm$ were manufactured to assess the features including compressive strength, microscopic structure, freezing and thawing, and degree of wet-dry. As results, it was found that with greater size specimen or contents of cement in the specimen, compressive strength, freezing and thawing resistance, and wet-dry resistance increase. Moreover, reactive products for each size of specimen were examined and it was possible to verify that some typical needle structured ettringite was generated due to blending of cement through microscopic structure analysis such as SEM and EDS analysis.