• Korean Journal of Agricultural Science
• /
• v.15 no.1
• /
• pp.36-46
• /
• 1988

Twelve soybean cultivars were cultivated in the 1/2,000a. Wagner pots with irrigation and without irrigation for 30 days after flowering, and the differences of plant growth and bean yield among cultivars were compared. And to investigate the varietal differences in the rate of photosynthesis under different relative humidity, 6soybean cultivars were cultivated in 1/2,000a. Wagner pot and the rate of photosynthesis of each soybean cultivar at flowering time was measured under the relative humidity of 80, 70, 60, 50 and 40%. The results obtained are summarized as follows; 1. The days to maturity of the soybean cultivars were shortened by non-irrigation treatment. The response of the maturing dates to non-irrigation was significantly different among the soybean cultivars. The days for maturing of Paldal, Danyeob and Eundaedu were delayed 2 days but those of Jangbaek and Tamahomare were delayed about 7 to 8 days under non-irrigation treatment. 2. The stem length, stem diameter, number of nodes of the mainstem, number of branches and number of branch nodes of all soybean cultivars were decreased by non-irrigation treatment. The number of branches and the number of branch nodes were especially severely influenced by non-irrigation treatment. 3. The number of pods per plant and the number of perfect pods was significantly reduced by non-irrigation treatment but the number of imperfect pods was increased. The non-irrigation treatment reduced the number of pods per plant by 58.0% and the ratio of the number of the perfect pods per plant by 46.6% relative to the ordinary cultivation with irrigation. 4. The grain yield of all cultivars was significantly reduced by the non-irrigation treatment, and average grain yield of soybean cultivars cultivated under non-irrigation treatment was 35.9% of that of soybean cultivars cultivated with irrigation. The influence of non-irrigation treatment was lowest in Paldal and significantly high in Tamahomare and Jangbaek. 5. The rate of photosynthesis of soybean leaves was significantly different among cultivars and was also influenced by relative humidity. Ratio of the photosynthetic amount of soybean leaves at 40% RH to the maximum photosynthesis at optimal humidity was 97.2% in Paldal, 96.4% in Danyeob and 88.8% in Baekun. 6. At 40% relative air humidity, highly significant correlations were found among the photosynthesis rate, the amount of transpiration and the respiration rate.

• Journal of Bio-Environment Control
• /
• v.27 no.3
• /
• pp.191-198
• /
• 2018

The objective of this study was to determine the effects of combination of air temperature and soil water contents on growth, physiological disorder rate, and yield of garlic. This experiments has been carried out in the typical plastic house (one side open and other side installed ventilation fans) which was maintained gradient air temperature (maximum different value of air temperature : $6^{\circ}C$). The excessive irrigation (EI) set at $0.34m^3/m^3$ soil moisture contents. The significant differences found in the growth parameters of garlics as affected by air temperature and soil moisture conditions. The plant height of garlic with combination of ambient $(A)+6^{\circ}C$ and optimal irrigation (OI; set at $0.22m^3/m^3$ soil moisture contents) treatments represented 47.4 cm/plant, which was the highest among all the tested treatments. The leaf length and width showed the greatest, which were 16.1 and 2.4 cm/plant, respectively, in $A+6^{\circ}C-OI$. The physiological disorder ratio was higher as 12.9% at $A+6^{\circ}C-OI$ and was not occurred at ambient temperature with EI compared with OI treatment. The bulb and clove weight were dramatically decreased at $A+6^{\circ}C$ temperature treatment. The yields were decreased by 51% in OI at $A+6^{\circ}C$ and $A+3^{\circ}C$ temperature treatment. Those results indicated that yields were decreased and ratio of physiological disorders was increased by high temperature treatments.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.64 no.3
• /
• pp.176-184
• /
• 2019

The rice variety Chucheongbyeo is mostly cultivated for organic farming in the central region of Korea. This variety is more delicate than the recently developed varieties in rice yield, quality, and pest resistance, and is therefore, not suitable for organic farming. This study was conducted to select suitable varieties for organic rice farming in the central plain area of Korea. We tested 15 different varieties in the organic paddy field of Cheongju city from 2011 to 2013. As the experimental field had good fertility because it had been organically managed for many years, culm length and number of panicles developed better than the varietal characteristics. Daebo, Chinnong and Hyeonpum had slightly lower ripened grain ratio than Chucheongbyeo. The milled rice yield of Samkwang, Sukwang, Haiami, Cheonghaejinmi and Daebo increased by 9-18% compared to that of Chucheongbyeo. The protein content was under 7% for Cheongnam, Sukwang, Daebo, Samkwang, Hyeonpum, Chinnong, Chilbo, Hopyung, Hwangkeumnuri, Suryeojinmi and Jinsumi and under 6% for Sukwang and Samkwang. The whiteness was over 40 in Sukwang, Daebo, Samkwang and Jinsumi. The palatability grade and head rice ratio were good in Daebo, Sukwang, Samkwang and Jinsumi. Therefore, this study recommended Samkwang, Daebo, and Jinsumi as the optimal varieties for organic rice farming in the central plain area of Korea. These varieties could replace Chucheongbyeo, which is inferior to the recently developed varieties in terms of disease and pest resistance and yielding performance.

• Journal of the Korean Society of International Agriculture
• /
• v.30 no.4
• /
• pp.370-375
• /
• 2018

In order to promote the mechanized cultivation of perilla for seed, which has been increasing in cultivation area and production recently as demand increases according to the health-functional effects, we carried out this experiment to determine the optimum sowing time of perilla to minimize the seed loss at harvest and increase the yield. We used two different types of perilla varieties, 'Sodam(small-branch)' and 'Deulsaem(multi-branch)', and the sowing time was June 15, June 30, July 15 and August 1. As the sowing time is late, days of growth from sowing to flowering were shortened, and they were shortened from 14, 26 and 31~32 days on June 30, July 15 and August 1 as compared with June 15, respectively. And, the stem length and culm diameter were shortened or tapered and the number of nodes tended to decrease. The number of effective branch was 82%, 61% and 56% on June 30, July 15 and August 1 as compared with June 15, respectively. Accordingly, it seems to make against in securing the yield from July 15. And, the lowest cluster height was generally shorter as the sowing time is late, and the height was below 15cm on July 15 and August 1. It seems that this may work against the machine harvest. There was a high degree of significance between the sowing time and the yield. Although, the total yield was not statistically significant among June 15, June 30 and July 15, the ratio of shattering seed at harvest was in order of July 15, August 1(30.3%)> June 15(15.3%)> June 30(13.5%). Therefore, the net yield except for shattered seed was higher in order of June 30${\geq}$ June 15> July 15> August 1. This tendency was characteristic regardless of variety and sowing method. And, the protein content in perilla seed increased as the sowing time was delayed, and the content was the highest on August 1. The content of crude fat was relatively high on June 15 and July 15 in 'Sodam', and June 30 and July 15 in 'Deulsaem', respectively. And, the content of linolenic acid was found to be the highest on August 1. As a result, the optimal sowing time for machine harvest of perilla for seed is about June 30. At this time, it is determined that the sowing time is the most suitable to be advantageous in increasing the yield of perilla seed, while minimizing the seed loss due to the shattering at harvest.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.13 no.4
• /
• pp.347-370
• /
• 2011

Slurry type shield would be very effective for the tunnelling in a sandy ground, when the slurry pressure would be properly adjusted. Low slurry pressure could cause a tunnel face failure or a ground settlement in front of the tunnel face. Thus, the stability of tunnel face could be maintained by applying an excess slurry pressure that is larger than the active earth pressure. However, the slurry pressure should increase properly because an excessively high slurry pressure could cause the slurry flow out or the passive failure of the frontal ground. It is possible to apply the high slurry pressure without passive failure if a horizontal impermeable layer is located in the ground in front of the tunnel face, but its location, size, and effects are not clearly known yet. In this research, two-dimensional model tests were carried out in order to find out the effect of a horizontal impermeable layer for the slurry shield tunnelling in a saturated sandy ground. In tests slurry pressure was increased until the slurry flowed out of the ground surface or the ground fails. Location and dimension of the impermeable layer were varied. As results, the maximum and the excess slurry pressure in sandy ground were linearly proportional to the cover depth. Larger slurry pressure could be applied to increase the stability of the tunnel face when the impermeable layer was located in the ground above the crown in front of the tunnel face. The most effective length of the impermeable grouting layer was 1.0 ~ 1.5D, and the location was 1.0D above the crown level. The safety factor could be suggested as the ratio of the maximum slurry pressure to the active earth pressure at the tunnel face. It could also be suggested that the slurry pressure in the magnitude of 3.5 ~4.0 times larger than the active earth pressure at the initial tunnel face could be applied if the impermeable layer was constructed at the optimal location.

• Geophysics and Geophysical Exploration
• /
• v.9 no.4
• /
• pp.279-290
• /
• 2006

The borehole radar methods used to tunnel detection are mainly classified into borehole radar reflection, directional antenna, crosshole scanning, and radar tomography methods. In this study, we have investigated the feasibility and limitation of each method to tunnel detection through case studies. In the borehole radar reflection data, there were much more clear diffraction signals of the upper wings than lower wings of the hyperbolas reflected from the tunnel, and their upper and lower wings were spreaded out to more than 10m higher and lower traces from the peaks of the hyperbolas. As the ratio of borehole diameter to antenna length increases, the ringing gets stronger on the data due to the increase in the impedance mismatching between antennas and water in the boreholes. It is also found that the reflection signals from the tunnel could be enhanced using the optimal offset distance between transmitter and receiver antennas. Nevertheless, the borehole radar reflection data could not provide directional information of the reflectors in the subsurface. Direction finding antenna system had a advantage to take a three dimensional location of a tunnel with only one borehole survey even though the cost is still very high and it required very high expertise. The data from crosshole scanning could be a good indicator for tunnel detection and it could give more reliable result when the borehole radar reflection survey is carried out together. The images of the subsurface also can be reconstructed using travel time tomography which could provide the physical property of the medium and would be effective for imaging the underground structure such as tunnels. Based on the results described above, we suggest a cost-effective field procedure for detection of a tunnel using borehole radar techniques; borehole radar reflection survey using dipole antenna can firstly be applied to pick up anomalous regions within the borehole, and crosshole scanning or reflection survey using directional antenna can then be applied only to the anomalous regions to detect the tunnel.

• Korean Journal of Medicinal Crop Science
• /
• v.15 no.6
• /
• pp.367-370
• /
• 2007

To make the soil moisture proper is the important factor in the seedbed cultivation of Yangjik for producing a good quality of ginseng seedling. This study was carries out to investigate the effect of soil moisture on photosynthesis and yield of ginseng seedling under the different condition of the soil moisture, such as $100{\sim}400$ mbar. Photosynthesis rate was decreased gradually by the reduction of soil moisture, and in particular it was decreased distinctly under the lower condition of soil moisture, such as $300{\sim}400$ mbar. Photosynthesis rate in air temperature of $30^{\circ}C$ was decreased more distinct than that of $25^{\circ}C$, Light saturation point of leaves was at the quantum of $600{\mu}mol/m^3/s$ at $25^{\circ}C$ while it was decreased by $300{\mu}mol/m^3/s$ at $30^{\circ}C$ according to the increase of air temperature. Respiration rate was increased by the increase of quantum, and decreased by the reduction of soil moisture. Respiration rate under the condition of high quantum was increased regardless of air temperature, but it was decreased distinctly under the condition of low soil moisture and high air temperature, such as 400 mbar at $30^{\circ}C$. There were a gradual decrease by the reduction of soil moisture in leaf length, leaf width, chlorophyll content, and water content of leaves, but heat injury ratio was increased distinctly by the reduction of it. Total root weight, root weight per plant, the yield of usable seedling were decreased by the reduction of soil moisture, and optimal content of soil moisture to produce a good quality of seedling was 63% of field capacity or 18.9% in absolute soil moisture content.

• Horticultural Science & Technology
• /
• v.34 no.1
• /
• pp.67-76
• /
• 2016

This study was conducted to examine the optimal environmental condition for promoting the growth of sowthistle as affected by light quality and photoperiod in a closed-type plant production system. Seeds were sown in 240-cell plug trays and then germinated for 3 days at a 24-hour photoperiod in a closed-type plant production system with LED lights (R:B:W = 8:1:1). Seedlings were transplanted and grown under 3 types of LED (R:B:W = 8:1:1, R:W = 3:7, or R:B = 8:2) and 4 photoperiods (24/0, 16/8, 8/16, or 4/20 hours) with $230{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ light intensity at a density of $20cm{\times}20 cm$. The experimental design was a randomized complete block design. Plants were cultured for 40 days un der the condition of $21{\pm}2^{\circ}C$ and $70{\pm}10%$ relative humidity after transplanting. Plants were fed with a recycling nutrient solution (pH 7.0 and EC $2.0dS{\cdot}m^{-1}$) contained in a deep floating tank. Fresh weight and dry weight of shoot or root, leaf length, and leaf area were the greatest in the photoperiod of 24/0 (light/dark) with RW LED. The highest number of leaves occurred in the photoperiod of 16/8 (light/dark) with RB LED, while the incidence of tip burn was higher in the photoperiod of 24/0 (light/dark) compared to the other treatments. Chlorophyll value was the highest in the 16/8 (light/dark) photoperiod and there was no significant difference by light quality. Chlorophyll fluorescence was the lowest in the photoperiod of 24/0 (light/dark) compared with other treatments. Therefore, in terms of economic feasibility and productivity for Ixeris dentata Nakai cultivation in a closed-type plant production system, the results obtained suggest that plants grew the best when kept in a photoperiod of 16/8 (light/dark) and light quality of combined LED RW (3:7).

• Journal of Chest Surgery
• /
• v.32 no.2
• /
• pp.108-118
• /
• 1999

Background: To evaluate the risk factor and long-term result of arterial switch operation , a retrospective study was done. Material and Method: A retrospective analysis was done to evaluate the early and long-term results on 58 patients who underwent an arterial switch operation(ASO) for transposition of the great arteries(TGA) with intact ventricular septum, between January 1988 and December 1996. Beforesurgery, 36 patients(62.1%) underwent balloon atrial septostomy, 32 patients(51.7%) received PGE1 infusion, and preparatory banding of pulmonary artery was performed on 6 patients(mean LV/RV pressure ratio 0.53$\pm$0.11). Result: The age at operation ranged from 1 to 137 days(mean 24$\pm$26 days) and the weights ranged from 1.8 to 6.8 kg (mean 3.5$\pm$0.8 kg). There were 14 early deaths(24.1%), but of the last 24 patients operated on since 1994, there were only 2 early deaths(8.3%). In the risk factor analysis, the date of operation was the only risk factor for early death(p-value < 0.01). Eight of the 14 early deaths were due to acute myocardial failure(mainly inadequate coronary blood flow). The length of follow-up ranged from 2 months to 8 years, average of 36$\pm$27 months. The follow-up included sequential noninvasive evaluations and 21 catheterizations and angiographic studies performed 5 to 32 months postoperatively with particular attention to the great vessel and coronary anastomosis, ventricular function, valvular competence, and cardiac rhythm. There were 5 late deaths(11.4%), one of thesedeaths was related to the late coronary problems, two to aspiration, one to uncontrolled chronic mediastinitis, and one to progressive aortic insufficiency and heart failure. The most frequent postoperative hemodynamic abnormality was supravalvular stenosis and the degree of pulmonary or aortic obstruction had slowly progressed in some cases, however there were no children who had to undergo a reoperation for supravalvular pulmonary or aortic stenosis. Aortic regurgitation was identified in 9 patients, which was mild in 7 and moderate in 2 and had progressed in some cases. Two patients who had an unremarkable perioperative course were identified as having coronary artery obstructions. The other late survivors were in good condition, were in sinus rhythm, and had normal LV functions. Actuarial survival rate at 8 years was 68.8%. Conclusion: We concluded that anatomic correction will be established as the optimal approach to the TGA with intact ventricular septum, though further long-term evaluations are needed.

• Journal of Aquaculture
• /
• v.10 no.4
• /
• pp.449-456
• /
• 1997

This study was concuted to determine the optimal conditions for raising the freshwater rotifer, Brachinus calyciflorus. The authors presented some biological informatin obtained from incubation experiment under the various controlled temperatures. Lorica size of the rotifer was divided into two groups : the length and the width for the S-type was $141.0\pm16.7\mu m$($110.1-182.5\;\mu m, n=44$)and $107.0\pm20.3\mu m\;(75.3-152.3\mu m, n=44)$, and those for the L-type was $262.8\pm15.2\mu m\;(234.4-288.6\mu m,\;n=20)\;and\;182.6\pm13.4\mu m (159.8-207.0\mu m,\;n=20$), respectively. The number of eggs being attached on the female varied from 1 to 11 at various culture conditions. Egg type was divided into two groups, large and small. Large and small egg was measured in its major axis as 85a.7-107.8$\mu$m and 55.1-65.2$\mu$m for S-type, and 104.9-121.8 $\mu$m and 62.8-89.1$\mu$m for L-type respectively. The maximum density was reached at 4th day after incubation. The density was 583.9 rotifers/$m\ell$ for $25^{\circ}C$-experimental. group and 421.3 rotifers/$m\ell$ for $22^{\circ}C$-experimental. group respectively. In the case of $28^{\circ}C$-experimental. group, it suddenly decreased into 4.7 rotifers/$m\ell$ at 1st day after incubations and did not recover to its initial density. The maximum rate of increase of populatin per day was reached 0.802 for $22^{\circ}C$-experimental. group at day 2 and fluctuated thereafter. For $25^{\circ}C$-experimental. group it increased to 0.964 at day 3 of incubation and then declined. And the egg ratio of female was reached the maximum of 0.614 for 22$^{\circ}C$- at 3rd day and 0.772 for $25^{\circ}C$-experimental. group at 4th day of incubation.