• Journal of Electrical Engineering and Technology
• /
• 제3권1호
• /
• pp.79-87
• /
• 2008

This paper proposes the design and implementation of a direct torque controlled induction motor drive system. The method is based on control of decoupling between amplitude and angle of reference stator flux for determining reference stator voltage vector in generating PWM output voltage for induction motors. The objective is to reduce electromagnetic torque ripple and stator flux droop which result in a decrease in current distortion in steady state condition. In addition, the proposed technique provides simplicity of a control system. The direct torque control is based on the relationship between instantaneous slip angular frequency and rotor angular frequency in adjustment of the reference stator flux angle. The amplitude of the reference stator flux is always kept constant at rated value. Experimental results are illustrated in this paper confirming the capability of the proposed system in regards to such issues as torque and stator flux response, stator phase current distortion both in dynamic and steady state with load variation, and low speed operation.

• 한국군사과학기술학회지
• /
• 제21권2호
• /
• pp.211-216
• /
• 2018

This paper presents a numerical optimization technique and switching phase control technique aiming at improvement of efficiency of the low voltage BLDC motor. The optimization technique is performed using the generalized sensitivity technique, response surface method(RSM) and sampling minimization technique. In order to minimize current consumption of the BLDC motor, the switching method of the driving device is optimized using RSM with finite element analysis. The ratings of BLDC motor are 50 W, 24 V, 1200 rpm. As optimizing results, the input current is reduced from 2.78 to 2.51 [A] when the switching phase is shifted by -2.65 [DEG_ELC] at the rated driving speed of 1200 [rpm]. It is confirmed that the proposed method reduces the consuming current of the low voltage BLDC motor through switching phase control method using the numerical optimization method.

• 한국태양에너지학회 논문집
• /
• 제35권1호
• /
• pp.35-43
• /
• 2015

A numerical simulation on the wake flow of a wind turbine which is a scaled version of a multi-megawatt wind turbine has been performed. Two different inlet conditions of averaged wind speed including one below and one above the rated wind speed were used in the simulation. Steady-state pitch angles of the blade associated with the two averaged wind speeds were imposed for the simulation. The steady state analysis based on the Reynolds averaged Navier-Stokes equations with the method of frame motion were used for the simulation to find the torque of the rotor and the wake field behind the wind turbine. The simulation results were compared with the results obtained from the wind tunnel testing. From comparisons, it was found that the simulation results on the turbine power are pretty close to the experimental values. Also, the wake results were relatively close to the experimental results but there existed some discrepancy in the shape of velocity deficit. The reason for the discrepancy is considered due to the steady state solution with the frame motion method used in the simulation. However, the method is considered useful for solutions with much reduced calculation time and reasonably good accuracy compared to the transient analysis.

• 대한기계학회논문집A
• /
• 제36권8호
• /
• pp.905-911
• /
• 2012

부유식 해상풍력발전기의 시뮬레이션을 위해서 본 연구에서는 2MW 육상 풍력발전기에 부유구조물인 Tension Leg Platform(TLP) 구조를 추가하였다. 기상청 관측데이터와 해수면으로부터의 높이에 대해 풍속을 정의하는 지수법칙을 이용하여 풍하중을 산출하고 블레이드와 타워에 일정한 높이간격으로 적용하였다. 상대모리슨 방정식을 이용하여 파랑하중을 모델링하였다. 블레이드의 회전속도를 정격속도인 18rpm 으로 고려하고, 풍하중과 파랑하중 작용 시 2MW의 부유식 해상풍력기의 동적거동 해석을 수행하였다. 파랑하중에 대한 해상풍력기의 공진특성을 조사하기 위해 타워와 블레이드의 탄성체 모델을 구성하여 해상풍력기의 고유진동수를 계산하였다. 타워와 블레이드의 탄성효과가 해상풍력기의 거동에 미치는 영향을 분석하기 위해 타워만 탄성체로 구성된 탄성타워모델과 타워와 블레이드가 탄성체로 고려된 탄성타워 블레이드모델을 각각 강체 모델과 비교하였다.

• 대한기계학회논문집A
• /
• 제36권9호
• /
• pp.1087-1094
• /
• 2012

본 논문에서는 구조 시험과 유한요소해석을 통하여 소형 풍력발전용 복합재 블레이드의 구조적 안전성을 평가하였다. 먼저, 선행연구에서 공력해석을 수행하여 정격 및 극한 풍속일 때의 블레이드가 받는 굽힘 모멘트를 산출하였다. 이를 이용하여 소형풍력발전기 관련 국제 규격인 IEC 61400-2에 따른 실규모 구조 시험을 수행하여 구조적 안전성을 평가하였다. 그리고 유한요소법을 이용한 구조 해석을 수행하여 구조 시험 결과와 비교하여 이의 정확성을 판단하였다. 또한, 구조 시험을 통해 블레이드에 대한 과잉 설계가 확인되었으며 이의 해결을 위하여 블레이드의 적층 순서 및 두께를 재선정하여 구조적 안전성을 평가하였다.