• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.8
• /
• pp.1102-1107
• /
• 1993

Microwave dielectric properties of CaTiO3 and CaTiO3-TiO2 ceramics for the composition range between 40 and 50 mol% CaO in CaO-TiO2 binary system were investigated. CaTiO3 ceramics with50 mol% CaO showed the dielectric constant (e,) of 178, the temperature coefficient of resonant frequency(c,) of+1000 ppm/'c and the qualify factor Q of 2760 (f0=2.7 GHz ). Dielectric constant and temperature coefficient of resonant frequency of ceramics with dual phases of CaTiO3 and TiO2 decreased gradually from those of CaTiO3 as the CaO content decreased. Q value and density were found to have minimum at the composition of 47 mol% CaO. The degradation of Q value and density in dual phase ceramics seems to be caused by the large pores at grain boundaries and/or within grains remained after rapid growth of CaTiO3 grains as TiO2 Phase decreased.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.363-368
• /
• 1999

Y-5a-Cu-O superconductors were prepared by TSMG (Top-Seeded Melt Growth) process with multiseeding technique. By using several seeds at the same time, large samples could be fabricated in a short time with simple heat treatment. However, the samples fabricated by normal multiseeding technique show the rapid decrease of trapped magnetic field value across the grain boundaries because of the residual liquid layer. To remove the residual liquid layer, modified multiseeding was newly suggested. The individual grains were combined as single domain, and did not show deterioration of magnetic property at the boundary. The formation mechanism of a well-combined domain by multiseeding technique was discussed.

• Journal of the Korean Vacuum Society
• /
• v.12 no.2
• /
• pp.130-135
• /
• 2003

Polycrystalline silicon thin films have been used for low cost thin film device application. However, it was very difficult to fabricate high performance poly-Si at a temperature lower than $600^{\circ}C$ for glass substrate because the crystallization process technologies like conventional solid phase crystallization (SPC) require the number of high temperature (600-$1000^{\circ}C$) process. The objective of this paper is to grow poly-Si on flexible substrate using a rapid thermal crystallization (RTC) of amorphous silicon (a-Si) layer and make the high temperature process possible on molybdenum substrate. For the high temperature poly-Si growth, we deposited the a-Si film on the molybdenum sheet having a thickness of 150 $\mu\textrm{m}$ as flexible and low cost substrate. For crystallization, the heat treatment was performed in a RTA system. The experimental results show the grain size larger than 0.5 $\mu\textrm{m}$ and conductivity of $10^{-5}$ S/cm. The a-Si was crystallized at $1050^{\circ}C$ within 3min and improved crystal volume fraction of 92 % by RTA. We have successfully achieved a field effect mobility over 67 $\textrm{cm}^2$/Vs.

• Korean Journal of Materials Research
• /
• v.17 no.9
• /
• pp.453-457
• /
• 2007

Interest in use of ink-jet printing for pattern-on-demand fabrication of metal interconnects without complicated and wasteful etching process has been on rapid increase. However, ink-jet printing is a wet process and needs an additional thermal treatment such as an annealing process. Since a metal ink is a suspension containing metal nanoparticles and organic capping molecules to prevent aggregation of them, the microstructure of an ink-jet printed metal interconnect 'as dried' can be characterized as a stack of loosely packed nanoparticles. Therefore, during being treated thermally, an inkjet-printed interconnect is likely to evolve a characteristic microstructure, different from that of the conventionally vacuum-deposited metal films. Microstructure characteristics can significantly affect the corresponding electrical and mechanical properties. The characteristics of change in microstructure and electrical resistivity of inkjet-printed silver (Ag) films when annealed isothermally at a temperature between 170 and $240^{\circ}C$ were analyzed. The change in electrical resistivity was described using the first-order exponential decay kinetics. The corresponding activation energy of 0.44 eV was explained in terms of a thermally-activated mechanism, i.e., migration of point defects such as vacancy-oxygen pairs, rather than microstructure evolution such as grain growth or change in porosity.

• Journal of the Korean Ceramic Society
• /
• v.43 no.10 s.293
• /
• pp.666-672
• /
• 2006

GDC20($Ce_{0.8}Gd_{0.2}O_{1.9}$) powder was synthesized by oxalate co-precipitation and milling and its thermal decomposition, phase formation, and sinterability were investigated. As-prepared precipitates were non-crystalline due to the milling process and completely decomposed at 400$^{\circ}C$ The powder calcined at 800$^{\circ}C$ for 2 h contained fine p]sty particles with an average size of 0.69 $\mu$m. Attrition milling of the calcined powder for 2 h had a little milling effect, resulting in a slight decrease in the particle size to 0.45 $\mu$m. The milled powder consisted of small spherical primary particles and some large particles, which had been agglomerated during calcination. Due to the excellent sinterability of the powder, sintering of the powder compacts for 4 h showed relative densities of 78.7% at 1000$^{\circ}C$ and 97.8% at 1300$^{\circ}C$, respectively. Densification was found to almost complete at temperature above 1200$^{\circ}C$ and a dense and homogeneous microstructure was obtained. A rapid grain growth occurred between 1200$^{\circ}C$ and 1300$^{\circ}C$. Grains in 0.1$\sim$0.5 $\mu$m sizes at 1200$^{\circ}C$ grew to 0.2$\sim$2 $\mu$m and their size distribution became broader at 1300$^{\circ}C$.

• The Korean Journal of Ceramics
• /
• v.2 no.2
• /
• pp.102-110
• /
• 1996

The Mg-PSZ/$Al_2O_3$ fibers were fabricated by the sol-gel method. The added $Al_2O_3$ amounts were varied from 5 to 20 mol%. The phase transformation studies of a drawn Mg-PSZ/$Al_2O_3$ fibers were investigated by use of X-ray diffraction, IR and Raman spectroscopy. Microstructure and tensile strength of fibers were subjected to scanning electron microscopy and tensile strength tester. When $Al_2O_3$ was added to the Mg-PSZ fibers, it was found out from the analysis of XRD patterns and Raman spectra that a small amount of crystalline spinel($MgAl_2O_4$) started to form due to the reaction between $Al_2O_3$ and MgO, at $1000^{\circ}C$, and the phase transformation temperature of $ZrO_2$ crystal phase at different sintering temperatures increased. Also, the rapid grain growth with average size of 2.0 ${\mu}m$ shown in Mg-PSZ fiber at $1500^{\circ}C$ was considerably suppressed to 0.39 ${\mu}m$ by adding $Al_2O_3$ at the same temperature. When the Mg-PSZ/$Al_2O_3$ fibers containing 5 mol% $Al_2O_3$ were sintered $800^{\circ}C$ for 1 hr, average tensile strength of fibers was 0.9 GPs at diameters of 20 to 30 ${\mu}m$, but as the sintering temperatures was increased to $1000^{\circ}C$ for 1 hr, average tensile strength of fibers increased to 1.2 GPa in the same diameter range.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.7
• /
• pp.503-509
• /
• 2013

In this study, $Cu(In_{1-x},Ga_x)Se_2$ (CIGS) thin films were prepared on the Mo coated soda-lime glass by the DC magnetron sputtering and a subsequent selenization process. For the selenization process, selenization rapid thermal process(RTP) with cracker cell, which was helpful to smaller an atomic of Se, was adopted. To make CIGS layer, they were then annealed with the cracked Se. Based on this selenization method, we made several CIGS thin film and investigated the effects of In deposition time, and selenization time. Through x-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive spectroscopy (EDS), and atomic force microscopy (AFM), it is found that the Mo/In/CuGa structure and the high sputtering power shows the dominant chalcopyrite structure and have a uniform distribution of the grain size. The CIGS films with the In deposition time of 5 min has the best structure due to the smooth surface. And CIGS films with the selenization time of 50 min show good crystalline growth without any voids.

• Korean Journal of Metals and Materials
• /
• v.49 no.8
• /
• pp.614-618
• /
• 2011

Nanopowders of MgO, $Al_2O_3$ and $SiO_2$ were made by high energy ball milling. The rapid sintering of nanostructured $MgAl_2O_4-Mg_2SiO_4$ composites was investigated by a high-frequency induction heating sintering process. The advantage of this process is that it allows very quick densification to near theoretical density and inhibition of grain growth. Nanocrystalline materials have received much attention as advanced engineering materials with improved physical and mechanical properties. As nanomaterials possess high strength, high hardness, excellent ductility and toughness, undoubtedly, more attention has been paid for the application of nanomaterials. Highly dense nanostructured $MgAl_2O_4-Mg_2SiO_4$ composites were produced with simultaneous application of 80MPa pressure and induced output current of total power capacity (15 kW) within 2min. The sintering behavior, gain size and mechanical properties of $MgAl_2O_4-Mg_2SiO_4$ composites were investigated.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.32 no.4
• /
• pp.447-454
• /
• 1987

Five soybean varieties of two early maturing; Karikei 73 and SS79168, and three late maturing; Tohoku 76, Baegunkong and Jangbaegkong, were used and evaluated in the study, Of the varieties examined, Karikei 73 was characterized by the delayed leaf senescence, To investigate the periodical trends of sugars in plant organs and their roles to the nitrogen fixing activity of root nodules, the concentrations of reducing and non-reducing sugar in root and nodules during the grain filling period were measured. The concentration of non-reducing sugar in roots was not changed up to the stage of R6 for all of the varieties but it decreased rapidly thereafter for the varieties except Karikei 73. No such rapid decrease in the concentration of non-reducing sugar in the roots was observed for Karikei 73 having the characteristics of delayed leaf senescence. The concentration of reducing sugar in the root nodules was not greatly changed for all of the varieties up to the stage of R6 regardless of the earliness of varieties but increased temporarily at R6.5 when there was a rapid decrease in ARA. The phenomenon explained the fact that nitrogen fixing activities were controlled not only by supplying sugars as the source of energy for nitrogen fixation, but also by the need for fixed nitrogen of the plant. The concentration of non-reducing sugar in root nodules also increased up to the stage of R6-R6.5 but decreased at R7, which could apply the same explanation as in the concentration of reducing sugar of the root nodules.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.27 no.4
• /
• pp.371-384
• /
• 1982

Highly cold tolerant varieties are requested not only at high latitute cool area but also tropical high elevated areas, and the required tolerance is different from location to location. IRRI identified 6 different types of cold tolerance required in the world for breeding purpose; a) Hokkaido type, b) Suweon type, c) Taipei 1st season type, d) Taipei 2nd season type, e) Tropical alpine type and, f) Bangladesh type. The cold tolerance requested in Korea is more eargent in Tongil group cultivars and their required tolerance is the one such as the physiological activities at low temperature are as active as in Japonica group cultivars at least during young seedling stage and reproduction stage. With conventional Japonica cultivars, such cold tolerant characters are requested as short growth duration but stable basic vegetative growth, less sensitive to high temperature and less prolonged growth duration at low temperature. The methods screening for cold tolerance were developed rapidly after the Tongil cultivar was reliesed. The facilities of screening for cold tolerance, such as, low temperature incubator, cold water tank, growth cabinet, phytotron, cold water nursery in Chuncheon, breeding nursery located in Jinbu, Unbong and Youngduk, are well established. Foreign facilities such as, cold water tank with the rapid generation advancement facilities, cold nurseries located in Banaue, Kathmandu and Kashimir may be available for the screening of some limitted breeding materials. For the reference, screening methods applied at different growth stages in Japan are introduced. The component characters of cold tolerance are not well identified, but the varietal differences in a) germinability, b) young seedling growth, c) rooting, d) tillering, e) discolation, f) nutrition uptake, g) photosynthesis rate, h) delay in heading, i) pollen sterility, and j) grain fertility at low temperature are reported to be distinguishable. Relationships among those traits are not consistent. Reported studies on the inheritance of cold tolerance are summarized. Four or more genes are controlling low temperature germinability, one or several genes are controlling seedling tolerance, and four or more genes are responsible for the pollen fertility of the rice treated with cold air or grown in the cold water nursery. But most of those data indicate that the results may come out in different way if those were tested at different temperature. Many cold tolerant parents among Japonicas, Indicas and Javanicas were identified as the results of the improvement of cold tolerance screening techniques and IRTP efforts and they are ready to be utilized. Considering a) diversification of germ plasm, b) integration of resistances to diseases and insects, c) identification of adaptability of recommending cultivars and, d) systematic control of recommending cultivars, breeding strategies for short term and long term are suggested. For short term, efforts will be concentrated mainly to the conventional cultivar group. Domestic cultivars will be used as foundation stock and ecologically different foreign introductions such as from Hokkaido, China or from Taiwan, will be used as cross parents for the adjustment of growth durations and synthsize the prototype of tolerances. While at the other side, extreme early waxy Japonicas will be crossed with the Indica parents which are identified for their resistances to the diseases and insects. Through the back corsses to waxy Japonicas, those Indica resistances will be transfered to the Japonicas and these will be utilized to the crosses for the improvement of resistances of prototype. For the long term, efforts will be payed to synthsize all the available tolerances identified any from Japonicas, Indicas and Javanicas to diversify the germ plasm. The tolerant cultivars newly synthsized, should be stable and affected minimum. to the low temperature at all the growing stages. The resistances to the diseases and insects should be integrated also. The rapid generation advancement, pollen culture and international cooperations were emphasized to maximize the breeding efficiency.