• 한국세라믹학회지
• /
• 제29권5호
• /
• pp.335-340
• /
• 1992

Undoped PbTiO3 ceramics was successfully prepared by using sol-gel process, which had not been fabricated due to its microcracks created by anisotropic stress during phase transition from cubic to tetragonal phase. Fabrication of undoped PbTiO3 ceramics via sol-gel processing was very much affected by the PbO content of the samples as well as PbO vapor from sintering atmosphere. Excess PbO was found to promote rapid grain growth in PbTiO3 ceramics. After sintering at 1100$^{\circ}C$ average grain size of PbTiO3 ceramics with excess PbO was about 8 times greater than that of stoichiometric composition, which may be due to PbO liquid phase from excess PbO.

• 한국분말재료학회지
• /
• 제1권1호
• /
• pp.15-20
• /
• 1994

The effect of SiC addition on sintering behaviors and microstructures of TiB2 ceramics were studied. The sintering of TiB2 was limited due to the surface diffusion and rapid grain growth at high temperature. However the addition of SiC to TiB2 ceramics improved the densification to above 99% of the theoretical density. The sintering of TiB2-SiC composite starts at 120$0^{\circ}C$ with the melting of the oxides in particle surface as impurities. After the reduction of the oxide by additional cabon at above 140$0^{\circ}C$, the grain boundary diffusion through the interface of TiB2-SiC play an important role. TEM observation showed neither chemical reactions nor other phases formed at the TiB2-SiC interfaces but the microcracks were observed due to the mismatch of thermal expansion between TiB2-SiC.

• 한국작물학회지
• /
• 제46권1호
• /
• pp.12-16
• /
• 2001

In order to develop near isogenic lines (NILs) the heterozygous rice plants for alkali digestibility value(ADV) were selected and tested in every generation from $F_5$to $F_9$ of a cross, Seratus malam/Suwon 345. Finally several sets of NILs, which were six low ADV lines and four medium-high ADV lines, were selected among $F_{10}$ lines. No differences of the plant growth characteristics, amylose content and protein content of rice grain were found between low and medium-high ADV lines. Rice flour of low ADV lines showed longer gel length in gel consistency test than medium-high ADV lines, and also showed different gelatinization characteristics measured by rapid visco analyzer compared with medium-high ADV lines. The result of genetic analysis indicated that ADV-NILs developed were differed in a pair of major gene controlling ADV, and low ADV was dominant over medium-high ADV.

• 한국분말재료학회지
• /
• 제31권1호
• /
• pp.23-29
• /
• 2024

This study investigates the effect of the microstructure of Li_1.3Al_0.3Ti_1.7(PO₄)₃ (LATP), a solid electrolyte, on its ionic conductivity. Solid electrolytes, a key component in electrochemical energy storage devices such as batteries, differ from traditional liquid electrolytes by utilizing solid-state ionic conductors. LATP, characterized by its NASICON structure, facilitates rapid lithium-ion movement and exhibits relatively high ionic conductivity, chemical stability, and good electrochemical compatibility. In this study, the microstructure and ionic conductivity of LATP specimens sintered at 850, 900, and 950℃ for various sintering times are analyzed. The results indicate that the changes in the microstructure due to sintering temperature and time significantly affect ionic conductivity. Notably, the specimens sintered at 900℃ for 30 min exhibit high ionic conductivity. This study presents a method to optimize the ionic conductivity of LATP. Additionally, it underscores the need for a deeper understanding of the Li-ion diffusion mechanism and quantitative microstructure analysis.

• 한국세라믹학회지
• /
• 제35권1호
• /
• pp.88-96
• /
• 1998

The structural and electrical properties of titanium dioxide(TiO2) thin films deposited on p-type (100) si and 4$^{\circ}$off(100) Si substartes by metalorganic chemical vapor deposition (MOCVD) have been studied with post rapid thermal annealing. TiO2 thin films of anatase phase were grown at 300-500$^{\circ}C$ using titanium post rapid thermal annealing at a temperature of 800$^{\circ}C$ for 30sec. rutile phase was observed in the condition of the deposition temperature over 350$^{\circ}C$ in the ambient air atmosphere and at 500$^{\circ}C$ in cacuu,. SEM and AFM study show-ed surface roughness were increased slightly from 40${\AA}$to 55${\AA}$ after annealing due to grain growth and phase transformation. From capacitane-voltage measurement of Al/TiO2./p-Si structure after annealing we obtained ideal capacitance-voltage characteristics of MOS structure with dielectric constant of 16-22 in case of (100) Si and about 30- in case of 4$^{\circ}$off(100) Si but showed the higher leakage current.

• 한국세라믹학회지
• /
• 제48권1호
• /
• pp.106-109
• /
• 2011

In order to fabricate 8YSZ thick film by silk screen printing, YSZ(yttria-stabilized zirconia) commercial powder was used as starting materials. Paste for screen printing was made by mixing 8YSZ powder and organic vehicles. 8YSZ thick film was formed on $Al_2O_3$ substrate. The crystal structure, and microstructure were investigated. Grain size of 8YSZ was increased with increasing calcination temperature and rapid grain growth was shown after calcination at $1300^{\circ}C$. Microstructure showed the mixture of large and small grain size after $1400^{\circ}C$ sintering. Shrinkage rate of 8YSZ thick film sintered at $1400^{\circ}C$ was more than 40%.

• 한국분말재료학회지
• /
• 제29권5호
• /
• pp.357-362
• /
• 2022

The low-temperature sinterability of TiO₂-CuO systems was investigated using a solid solution of SnO₂. Sample powders were prepared through conventional ball milling of mixed raw powders. With the SnO₂ content, the compositions of the samples were Ti_1-xSn_xO₂-CuO(2 wt.%) in the range of x ≤ 0.08. Compared with the samples without SnO₂ addition, the densification was enhanced when the samples were sintered at 900℃. The dominant mass transport mechanism seemed to be grain-boundary diffusion during heat treatment at 900℃, where active grain-boundary diffusion was responsible for the improved densification. The rapid grain growth featured by activated sintering was also obstructed with the addition of SnO₂. This suggested that both CuO as an activator and SnO₂ dopant synergistically reduced the sintering temperature of TiO₂.

• 한국작물학회지
• /
• 제45권1호
• /
• pp.14-19
• /
• 2000

In order to develop an appropriate cultural practice for a newly bred 2-rowed, waxy, naked barley cultivar 'Duwonchapssalbori' in the southern region, 2 varieties, 3 seeding dates, 4 seeding rates were designed with 2 replications. The heading and maturity dates of 'Duwonchapssalbori' were' earlier than 'Saessalbori by 2-5 and 4 days, respectively. Culm length of 'Duwonchapssalbori' was 60 to 66cm with lodging resistance. Grain yields of both varieties were 4.28-4.33 ton/ha in the plot of Oct. 20 seeding, 4.11-4.18 ton in the plot of Oct. 28 seeding, and 3.7-13.89 ton/ha in the Nov. 5 seeding. Grain yield with different seeding rates highly significantly fitted with secondary polynomial equations in the plots of Oct. 20 and Oct. 28 seedings ($R^2$=0.84-0.85), showing the greatest yield with seeding rate of 140kg per ha. However, the grain yield with various seeding rates in the plot of Nov. 5 seeding showed simple linear regression ($R^2$=0.71), showing the seeding rate over 160kg in the case of later seeding to be optimal. Number of spikes per $m^2$ significantly contributed to grain yield, and fitted to simple linear regression ($R^2$=0.881-0.891), suggesting that plenty of early stands should be established at early seedling stage for high grain yield. Young spikes of 'Duwonchapssalbori' in the plot of Oct. 20 seeding elongated with linear increments since Feb. 10 (6.7mm), and showed rapid increment since March 7 (15.1mm). However, elongation of young spikes of 'Saessalbori' began from March 15 with slow increments. From these studies, the optimum seeding date and seeding rate in 'Duwonchapssalbori' were Oct. 20-28 and 140kg per ha for high grain yield in the southern regions.

• 한국분말재료학회지
• /
• 제23권2호
• /
• pp.132-135
• /
• 2016

This study investigates the influence of sintering temperature on the magnetic properties and frequency dispersion of the complex permeability of Ni-Zn-Cu ferrites used for magnetic shielding in near-field communication (NFC) systems. Sintered specimens of $(Ni_{0.7}Zn_{0.3})_{0.96}Cu_{0.04}Fe_2O_4$ are prepared by conventional ceramic processing. The complex permeability is measured by an RF impedance analyzer in the range of 1 MHz to 1.8 GHz. The real and imaginary parts of the complex permeability depend sensitively on the sintering temperature, which is closely related to the microstructure, including grain size and pore distribution. In particular, internal pores within grains produced by rapid grain growth decrease the permeability and increase the magnetic loss at the operating frequency of NFC (13.56 MHz). At the optimized sintering temperature ($1225-1250^{\circ}C$), the highest permeability and lowest magnetic loss can be obtained.

• 대한금속재료학회지
• /
• 제46권4호
• /
• pp.223-226
• /
• 2008

The comparison of sintering behavior and mechanical properties of ultra-fine WC-10wt.%Co and WC-10wt.%Fe hard materials produced by high-frequency induction heated sintering (HFIHS) was accomplished using ultra fine powder of WC and binders(Co, Fe). The advantage of this process allows very quick densification to near theoretical density and prohibition of grain growth in nano-structured materials. Highly dense WC-10Co and WC-10Fe with a relative density of up to 99% could be obtained with simultaneous application of 60 MPa pressure and induced current within 1 minute without significant change in grain size. The hardness and fracture toughness of the dense WC-10Co and WC-10Fe composites produced by HFIHS were investigated.