• Journal of Biomedical Engineering Research
• /
• v.35 no.3
• /
• pp.35-41
• /
• 2014

In this study, joint angles of the lower extremity and inertial sensor data such as accelerations and angular velocities were measured during a ski simulator exercise in order to evaluate the skill of skiers. Twenty experts and twenty unskilled skiers were recruited for the study. All expert skiers held the certificates issued by the Korea Ski Instructors Association. A three-dimensional motion capture system and two inertial sensors were used to acquire joint movements, heel acceleration and heel angular velocity during ski simulator exercises. Pattern variation values were calculated to assess the variations in ski simulator motion of expert and unskilled skiers. Integral ratio of roll angular velocity was calculated to determine the parallel alignment of the two feet. Results showed that ski experts showed greater range of motion of joint angle, peak-to-peak amplitude(PPA) of heel acceleration and PPA of heel angular velocity than unskilled skiers. Ski experts showed smaller pattern variations than unskilled skiers. In addition, the integral ratio of roll angular velocity in ski experts was closer to 1. Inertial sensor data measurements during the ski simulator exercises could be useful to evaluate the skill of the skier.

• The Journal of Korean Academy of Prosthodontics
• /
• v.61 no.4
• /
• pp.257-267
• /
• 2023

Purpose. The purpose of the study was to fabricate a prototype robotic simulator for dental education, to test whether it could simulate mandibular movements, and to assess the possibility of the stimulator responding to stimuli during dental practice. Materials and methods. A virtual simulator model was developed based on segmentation of the hard tissues using cone-beam computed tomography (CBCT) data. The simulator frame was 3D printed using polylactic acid (PLA) material, and dentiforms and silicone face skin were also inserted. Servo actuators were used to control the movements of the simulator, and the simulator's response to dental stimuli was created by pressure and water level sensors. A water level test was performed to determine the specific threshold of the water level sensor. The mandibular movements and mandibular range of motion of the simulator were tested through computer simulation and the actual model. Results. The prototype robotic simulator consisted of an operational unit, an upper body with an electric device, a head with a temporomandibular joint (TMJ) and dentiforms. The TMJ of the simulator was capable of driving two degrees of freedom, implementing rotational and translational movements. In the water level test, the specific threshold of the water level sensor was 10.35 ml. The mandibular range of motion of the simulator was 50 mm in both computer simulation and the actual model. Conclusion. Although further advancements are still required to improve its efficiency and stability, the upper-body prototype simulator has the potential to be useful in dental practice education.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.10a
• /
• pp.53-54
• /
• 2017

In this paper, we have studied the electrostatic discharge test for the battery protection circuit module in the lithium ion battery used as a smartphone battery which is used to prevent the explosion hazard due to overcharge, over discharge, and short-circuit. A lithium ion battery of S company was used as an experimental sample, and an ESD gun simulator compliant with IEC 61000-4-2 standard was used for electrostatic discharge injection. The contact discharge was applied to the various pins of the battery protection circuit module in increments of 2 kV in the range of 2 kV to 10 kV and in 5 kV increments in the range of 10 kV to 30 kV.

• Journal of Astronomy and Space Sciences
• /
• v.18 no.2
• /
• pp.119-128
• /
• 2001

The oscillation frequency tuning range of waveguide Gunn oscillator and its stability depend sensitively on the dimensions of the resonator. Therefore the embedding impedances with the various dimensions of the resonator for Q-band (33 ∼ 50 GHz) Gunn oscillator are calculated by using HFSS (High Frequency Structure Simulator). In this paper the comparisons between theoretical results of embedding impedances as a function of frequency and that of experimental results are described. And the oscillation frequency range could be predicted by using the theoretical evaluation methods which were proposed in this paper It shows that post size has an effect on the frequency tuning characteristics of Gunn oscillator.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.05c
• /
• pp.55-58
• /
• 2001

In this paper, we present the results of the design and fabrication of the VCO(Voltage controlled Oscillator) using RF circuit simulator GENESYS and electromagnetic field simulator EMpower Frequency range is fabricated VCO is 850 MHz ~ 950 MHz, which is used Colpitts Circuit. the fabricated VCO is consisted of resonator, oscillator and MSL(Microstrip Line) is used in LC tuning circuit.(operated by negative feedback) MSL(Microstrip Line), Varactor(Plastic package), low noise TR(SOT-23), chip inductor(1608), chip capacitor(1005), chip resistance(1005). 1005 type is used for sample fabrication of VCO. In the fabrication process, circuit pattern is screen printed on the alumina substrates of over 99.9% purity. Center frequency of the sample VCO is 850MHz at $V_T=1.5V$, while the simulated value was 1.0GHz at $V_T=1.5V$. Variable frequency range of the sample is 860~950MHz in contrast to the 1068~1100MHz of the simulated values.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.05c
• /
• pp.153-156
• /
• 2001

In this paper, we present the results of the design and fabrication of the VCO(Voltage controlled Oscillator) using RF circuit simulator GENESYS and electromagnetic field simulator EMpower Frequency range is fabricated VCO is 850 MHz ~ 950 MHz, which is used Colpitts Circuit. the fabricated VCO is consisted of resonator, oscillator and MSL(Microstrip Line) is used in LC tuning circuit.(operated by negative feedback) MSL(Microstrip Line), Varactor(Plastic package), low noise TR(SOT-23), chip inductor(1608), chip capacitor(1005), chip resistance(1005). 1005 type is used for sample fabrication of VCO. In the fabrication process, circuit pattern is screen printed on the alumina substrates of over 99.9% purity. Center frequency of the sample VCO is 850MHz at $V_T$=1.5V, while the simulated value was 1.0GHz at $V_T$=1.5V. Variable frequency range of the sample is 860~950MHz in contrast to the 1068~1100MHz of the simulated values.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.7B
• /
• pp.1058-1065
• /
• 2010

In the recent, the importance of ubiquitous-related technique is increased as many companies and researchers make an effort to create a new service model using ubiquitous computing and network technologies. Especially, the research of indoor location recognition has gained a lot of interest because it is a critical component for supporting ubiquitous services. Nevertheless, the simulation tool for indoor location recognition hardly has studied compared to their importance. In this paper, we propose a Ptolemy-based simulator over UWB channel that provides short-range and high-bandwidth communication. Finally, we conduct experiments using the proposed simulator and analyze the performance of various location recognition algorithms.

• Journal of Sensor Science and Technology
• /
• v.16 no.1
• /
• pp.44-51
• /
• 2007

A hybridized simulator for generating blood pressure waveform is proposed to study the remedy and/or evaluation of the conventional sphygmomanometer utilizing the oscillometric method which is widely applied. The blood pressure of a flowing fluid was controlled for the blood vessel's condition caused by a rhythmical and periodical contraction/relaxation because of the special excitatory and conductive system of the heart. In this study, a hybridized controller composed of the PI feedback controller and the feedforward controller. The inverse dynamics function is proposed to operating the control valve while the pressure is applied in an oil pressure tank. The proposed hybrid simulator reproducing the blood pressure waveform in an artificial blood vessel has kept the control performance consistent over all range. Based on these results, the proposed simulators could be applied to the development and compensation of the non invasive sphygmomanometer type as well as to study the characteristics of the blood pressure and blood vessel.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.6 no.1
• /
• pp.83-90
• /
• 2010

DTNs (Delay Tolerant Networks) refer to the networks that can support data transmission in the extreme networking situations such as continuous delay and no connectivity between ends. DTMNs (Delay Tolerant Networks) are a specific range of DTNs, and its chief considerations in the process of message delivery in the routing protocol are the transmission delay, improvement of reliability, and reduction of network loading. This article proposes a new LCN (Largest Common Neighbor) routing algorism to improve Spray and Wait routing protocol that prevents the generation of unnecessary packets in a network by letting mobile nodes limit the number of copies of their messages to all nodes to L. Since higher L is distributed to nodes with directivity to the destination node and the maximum number of common neighbor nodes among the mobile nodes based on the directivity information of each node and the maximum number of common neighbor nodes, more efficient node transmission can be realized. In order to verify this proposed algorism, DTN simulator was designed by using ONE simulator. According to the result of this simulation, the suggested algorism can reduce average delay and unnecessary message generation.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.9
• /
• pp.842-849
• /
• 2011

The human ear canal amplifies the sound pressure level at specific frequency bands. The characteristics of the ear canal are very similar to those of curved cylindrical tube. In this study, the characteristics of sound transfer in human ear canal were measured and the acoustical space of ear canal was reproduced from the canal cavity geometry. For the measurement of sound transfer function in ear canal, a probe microphone and a reference microphone were used. The sound transfer functions were measured for 5 human subjects. To reproduce the acoustical space of the ear canal, two kinds of ear simulator were designed. The first one is a straight cylindrical tube type and the other is a real-shape ear of which geometry was taken from a micro-CT scanning of a human ear. The characteristics of the reproduced apparatus were compared with those of the human and a commercial ear simulator, RA0045 of G.R.A.S. Inc. The comparison results show that the developed apparatus well represent the ear canal characteristics in the low frequency, but have limited coincidence in level over high frequency range.