• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.180-184
• /
• 2009

A novel set of experimental test tooling for measuring pulling and holding forces for drawbeads on binders inclined at a wide range of angles is introduced. A mechanical design featuring a single load cell, a male-female draw bead set, translation and rotation degrees of freedom, and a screw-driven clamping system has been incorporated into a standard tensile test machine. On a real time basis, restraining and holding force data with respect to draw-in displacement may be directly downloaded into a PC for data processing. The proposed experimental system represents a significant breakthrough in drawbead simulation technology due to its relatively low cost, clever design, and versatility. The system is shown to yield excellent experimental data suitable for verifying theory and numerical model predictions.

• 한국컴퓨터정보학회논문지
• /
• 제20권10호
• /
• pp.1-5
• /
• 2015

Based on the dual hardware and software with distributed recovery blocks, the centralized type fault tolerant store management system(SMS) was proposed. As a result of trade off study related to mutiplex hardware system design, dual single board computer(SBC) was adapted. To verify redundancy function of the proposed structure, the prototype SMS and weapon simulator were used. The proposed SMS operated normally without being affected by a primary SBC failure. The switching time from primary SBC to shadow SBC was within 200 ms. The reliability of the proposed SMS was predicted and compared with the non fault tolerant SMS, thereby it was proved that the proposed SMS has a higher reliability than the non fault tolerant system within effective range.

• Journal of Electrical Engineering and Technology
• /
• 제13권1호
• /
• pp.97-104
• /
• 2018

This paper proposes supplementary control of conventional coordinated control of a power plant which directly affects network frequency. The supplementary control with dynamic matrix control is applied for 1000 MW power plant with ultra-supercritical (USC) once-through boiler. The supplementary control signal is added to the boiler feedforward signal in the existing coordinated control logic. Therefore, it is a very practical structure that can maintain the existing multi-loop control system. This supplementary controller uses the step response model for the power plant system, and on-line optimization is performed at every sampling step. The simulation results demonstrate the effectiveness of the proposed supplementary control in a wide operating range of a practical 1000 MW USC power plant simulator. These results can contribute the stable operation of power system frequency.

• 전기학회논문지
• /
• 제67권9호
• /
• pp.1210-1215
• /
• 2018

Recently, as the IoT(Internet of Things) and AI(Artificial Intelligence) technologies have developed, smart toys that can understand and act on the language of human beings are being studied. In this paper, we study voice learning using CNN(Convolutional Neural Network) by applying artificial intelligence based voice secretary technology to smart toy. When a human voice command gives, Smart Toy recognizes human voice, converts it into text, analyzes the morpheme, and conducts tagging and voice learning. As a result of test for the simulator program implemented using Python, no malfunction occurred in a single command. And satisfactory results were obtained within the selected simulation condition range.

• 한국안전학회지
• /
• 제23권5호
• /
• pp.1-6
• /
• 2008

`SOS', Simulator Of Safety assessment for fire, was developed to simulate fire safety assessment for a structure which is geometrically complex. The program(SOS) is intended to use for searching as well as designing tools to analyse the evacuation safety through a wide range of structure conditions. The computer program has a function which importing FDS's calculating results to each individual resident in the structure. These attributes include a walking speed reduction by producing visibility reduction for each person on the fire. $A^*$ pathfinding algorithm is adopted to calculate the simulation of escape movement, overtaking, route deviation, and adjustments individual speeds in accordance with the proximity of crowd members. This SOS program contributes to a computer package that evaluates the fire safety assessment of individual occupants as they walk towards, and through the exits especially for building, underground spaces like a subway or tunnel.

• 한국전기전자재료학회논문지
• /
• 제15권4호
• /
• pp.344-348
• /
• 2002

As microelectronics technology continues to progress, there is also a continuous demand on highly integration and miniaturization of systems. For example, it is desirable to package several integrated circuits together in multilayer structure, such as multichip modules, to achieve higher levels of compactness and higher performance. Passive components (i.e., capacitors, resistors, and inductors) are very important fort many MCM applications. In addition, the low-temperature co-fired ceramic (LTCC) process has considerable potential for embedding passive components in a small area at a low cost. In this paper, we investigate a method of statistically modeling integrated passive devices from just a small number of test structures. A set of LTCC inductors is fabricated and their scattering parameters (s-parameters) are measured for a range of frequencies from 50MHz to 5GHz. An accurate model for each test structure is obtained by using a building block based modeling methodology and circuit parameter optimization using the HSPICE circuit simulator.

• 한국전기전자재료학회논문지
• /
• 제24권6호
• /
• pp.449-457
• /
• 2011

Effect of pump combinations on the vacuum characteristics of vacuum system was simulated for optimum design of system. In this investigation, the feasibility of modelling mechanism for VacSimMulti simulator was proposed. Simulation results of various pumping combinations showed the possibilities and reliabilities of simulation for the performance of vacuum system in specific semiconductor processing. Simulation of roughing pump presented the expected pumping behaviors based on commercial specifications of employed pumps. Application of booster pump exhibited the high pumping efficiency for middle vacuum range. Combinations of optimum backing pump for diffusion and turbo vacuum system were obtained. And, the predictable characteristics of process application of both simulated systems were also acquired.

• 한국정밀공학회지
• /
• 제16권3호통권96호
• /
• pp.128-135
• /
• 1999

A driving simulators of aircraft and vehicle may consist of hydraulic power systems with many single-rod cylinders. The single-rod hydraulic systems are convenient but need more robust control scheme in order to achieve a reliable performance against the wide range of operating disturbances and the inherent model uncertainties. $H_{\infty}$ control scheme was implemented to the 2 degree-of-freedom hydraulic device similar to the simple driving simulator. With the reasonable disturbances from sensor, base and pump and also with the linearization of model, the simulation and experimental results showed good agreements.

• Journal of electromagnetic engineering and science
• /
• 제19권1호
• /
• pp.13-19
• /
• 2019

This paper proposes a systematic method for estimating detection performances of a frequency-modulated continuous wave radar using electromagnetic simulations. The proposed systematic method includes a radar system simulator that can obtain range-Doppler images using the electromagnetic (EM) simulations in conjunction with a test setup employed for performance evaluation of multiple targets at different velocities in a traffic environment. This method is then applied for optimizing the half-power beamwidths of the antenna array using an evaluation metric defined to improve the detection strengths for the multiple targets. The optimized antenna has vertical and horizontal half-power beam widths of $10^{\circ}$ and $60^{\circ}$, respectively. The results confirm that that the proposed systematic method is suitable to improve the radar detection performance with the enhanced radar-Doppler images.

• International Journal of Computer Science & Network Security
• /
• 제21권9호
• /
• pp.358-361
• /
• 2021

In this paper, we have simulated a rectangular microstrip patch antenna for aerospace applications based on graphen as a conductor and a multilayer substrate .as a result of the use of the graphen patch we obtained a reconfigurable antenna on the frequency range (0.6-0.7 terahertz) with a gain up to 12 db. The simulation of this antenna has been performed by using CST Microwave Studio, which is a commercially available finite integral based electromagnetic simulator.