• Journal of the Korean Society of Safety
• /
• v.27 no.2
• /
• pp.117-126
• /
• 2012

Understanding driver's characteristic of visual activity is important process because driver depends on a visual signal more than 90% for getting outside information needed to drive, thus a series of driving, including perception, judgement, and activity, is completed. This study analyzes quantified driver's sight range in curved section where recognition of various information is critical due to biggest speed change among sections. Simulation is utilized for this study because of safety problem on field experiment and difficulties in using equipment. Building 6 roads that have different in curve radius by virtual driving map, experiment is carried out recruiting 30 people. Through analytical researches, it shows that drivers keep an eye on direction of driving, and driver's visual range is narrowed on left curve than right curve, and the more curve radius become small, the more drivers see in narrow angle.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.4
• /
• pp.589-595
• /
• 2014

The error of instrument transformers is measured by connecting the external burden with the secondary terminal of the instrument transformers. Because the error of transformer is affected by the apparent power and power factor of the external burden, an accurate measurement of burden is important for transformer evaluation. We have developed the burden evaluation equipment for both potential transformer and current transformer by employing the series resistor in the range of $20m{\Omega}{\sim}5{\Omega}$ and the parallel resistor in the range of $1M{\Omega}{\sim}500{\Omega}$, respectively, together with visual basic program. We could reduce testing time more than 5 times by employing method developed in this study, compared with that developed in past. This method shows more better reliability by analyzing the evaluation results and fitting graphs of burden measurements. The test results of the developed system is compared with those obtained in the power meter analyzer to verify the validity.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2007.11a
• /
• pp.337-340
• /
• 2007

In the dissertation, a power conversion system for fuel cell is composed of a PWM inverter with LC filter in order to convert fuel cell voltage to a single phase 220[V], In addition, new insulated DC-DC converters are proposed in order that fuel cell voltage is boosted to 380[V]. In this paper, it requires smaller components than existing converters, which makes easy control. The proposed DC-DC converter controls output power by the adjustment of phase-shift width using switch S5 and S6 in the secondary switch, which provides 93-97[%] efficiency in the wide range of output voltage. Fuel cell simulator is implemented to show similar output characteristics to actual fuel cell. Appropriate dead time td enables soft switching to the range where the peak value of excitation current in a high frequency transformer is in accordance with current in the primary circuit. Moreover, appropriate setting to serial inductance La reduces communication loss arisen at light-load generator and serge voltage arisen at a secondary switch and serial diode. Finally, TMS320C31 board and EPLD using PWM switching technique to act a single phase full-bridge inverter which is planed to make alternating current suitable for household.

• Journal of Advanced Navigation Technology
• /
• v.10 no.1
• /
• pp.7-12
• /
• 2006

In this paper, we investigated performance for 5.8GHz dedicated short range communication system using OFDM which will be applied to Intelligent transportation system services. The maximum speed of a vehicle in DSRC channel is very fast as 180km/h, so a service time is very short to serve a various traffic information if hand-off is not occurred. Therefore higher bit rate is required to proved advanced and intelligent service to the drivers of various vehicle and the data transmission rate of the next generation DSRC system if being promoted over 10Mbps. The signals received in Racian channel have been simulated using the computer simulator. For performance improvement, BCH coding scheme are adopted.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.767-769
• /
• 1998

Using the R/V converting circuit, hydrogen detecting characteristics of the $WO_3$ films were investigated. The R/V converting circuit is configured with the equivalently constant current driving method connecting an unknown resistor to be measured in the feedback loop of the or-amr rather than using a separated constant current circuit. The response time of the reference voltage for the R/V converting circuit was simulated by the circuit simulator "SABER", and it was found that the response time in the high resistance range become longer and the error amounts to 10%. From the simulation results. replacing the capacitor in the feedback loop of the second stage or-amp with a 0.001uF capacitor, when measuring in the high resistance range, the response characteristics are remarkably improved. The response time was shortened from about 10 seconds to below 1 second. Using this circuit, the effect of $WO_3$ films deposited by sputtering method on hydrogen was measured.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.38-42
• /
• 2002

HAZ(Heat Affected Zone of weldm ents) properties were investigated for a high nitrogen austenitic stainless steel with a chemical composition of Fe-0.02C-0.15Si-6.00Mn-10.0Ni-23.0Cr-2.00Mo-0.48N-0.14V. Thermal cycle of HAZ was simulated by the thermal cycle simulator (Gleeble 1500). The heat treatment was applied to the Charpy test size sample without notch under various peak temperatures and/or the holding times condition. V-notch Charpy test was performed at the temperature range of 273~77 K. Metallographic examination also was carried out by using optical microscopy, scanning electron microscopy and transmission electron microscopy. The simulated specimens revealed a slight embrittlement compared with the base materials. The impact toughness of the specimens deteriorated with the decreasing test temperature. The results from Charpy V-notch test, however, showed that significant degradation of absorbed energy caused by brittle fracture was not observed for the specimen tested in the test temperature range.

• Journal of the Ergonomics Society of Korea
• /
• v.24 no.4
• /
• pp.55-62
• /
• 2005

This study examined the effect of ergonomic heel rest that was designed for drivers who have physical handicap in the low leg muscles or have to drive prolonged hours with frequent foot pedaling. An experiment was designed to test the ergonomic heel rest with traditional foot pedal. Forty subjects participated in the experiment. Electromyography(EMG) was used to monitor the muscle activity and fatigue of right leg, and Electro-goniometer was used to measure the ranges of motions of the knee and ankle. A simulator of driver's seat was built for the experiment and the heel rest was installed on it. In order to examine the low muscle activity and range of motion, subjects used the foot pedal for 15 minutes repetitively for each experimental condition. Another 15 minutes test without the heel rest was also performed for comparison. The Root Mean Square(RMS) and Mean Power Frequency(MPF) Shift were used to quantify the level of muscle activity and local muscle fatigue. In results, statistically significant decreases of muscle activity and fatigue were found in all the low leg muscles. The range of motion of the knee and ankle joint also decreased when the heel rest was used. The mechanism of the heel rest effect was discussed in this study. This type of heel rest can be applied to real driving situation after ensuring the safety, or overcoming the psychological discomfort possibly due to unfamiliarity.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.35C no.12
• /
• pp.59-65
• /
• 1998

In this paper, a novel rail-to-rail input stage circuit with improved transconductance Is designed. Its excellent performances over whole common-mode input voltage Vcm range is demonstrated by circuit simulator HSPICE. The novel input stage circuit comprises additional 4 input transistors and 4 current sources/sinks. It maintains DC currents of signal amplifying transistors when one of the differential input stage circuits operates, but it reduces these currents to 1/4 when both differential input stage circuits operates, As a result, a operational amplifier with the novel circuit maintains nearly constant transconductance performance and unity-gain frequency in strong inversion region. The novel circuit allows an optimal frequency compensation and uniform operational amplifier performance over whole Vcm range.

• ETRI Journal
• /
• v.39 no.2
• /
• pp.234-244
• /
• 2017

Research interest in three-dimensional multiple-input multiple-output (3D-MIMO) beamforming has rapidly increased on account of its potential to support high data rates through an array of strategies, including sector or user-specific elevation beamforming and cell-splitting. To evaluate the full performance benefits of 3D and full-dimensional (FD) MIMO beamforming, the 3D character of the real MIMO channel must be modeled with consideration of both the azimuth and elevation domain. Most existing works on the 2D spatial channel model (2D-SCM) assume a wide range for the distribution of elevation angles of departure (eAoDs), which is not practical according to field measurements. In this paper, an optimal FD-MIMO planar array configuration is presented for different practical channel conditions by restricting the eAoDs to a finite range. Using a dynamic network level simulator that employs a complete 3D SCM, we analyze the relationship between the angular spread and sum throughput. In addition, we present an analysis on the optimal antenna configurations for the channels under consideration.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.9
• /
• pp.30-37
• /
• 2000

In this paper, design and fabrication of miniature voltage-controlled oscillator(VCO) is discussed . Based on the two-port circuit analysis technique, VCO for 900MHz cellular mobile phone is designed and circuit parameters are optimized using the circuit simulator. Using the optimized design parameters, miniature VCO with 6${\times}$6${\times}$1.8 mm$^3$(0.065cc) dimensions is fabricated and experimented. Experimental results show that implemented VCO has -3.5 dBm output power level and 45MHz tunung range, respectively, and has -101.5dB/Hz Phase noise performance at 10 KHz frequency offset.