• Journal of the Korean Society of Systems Engineering
• /
• v.17 no.2
• /
• pp.37-48
• /
• 2021

Improving the plant protection system against unforeseen changes/transients during operation is essential to maintain plant safety. Under this condition, it requires rapid and accurate signal processing. The use of an Intellectual Property (IP) core for floating point calculations for Safety Critical MMIS can make numerical computations easier and more precise, improving system accuracy. It can represent and manipulate rational numbers as well as a much broader range of values with dynamic range in nuclear power plant. Systems engineering approach (SE) is used through the development process, it helps to reduce complexity and avoid omissions and invalid assumptions as delivers a better understanding of the stakeholders needs. For the implementation on the FPGA target board, the 32-bit floating-point arithmetic with IEEE-754 standards has designed using Simulink model in Matlab for all operations of addition, subtraction, multiplication and division and VHDL code generated.

• Analytical Science and Technology
• /
• v.28 no.4
• /
• pp.299-307
• /
• 2015

In May 2012, a safety hazard issue arose because some kiwifruit growers in New Zealand had sprayed streptomycin to prevent kiwifruit canker. Therefore, for food safety management, analytical methods to determine streptomycin residues in kiwifruits are required. We developed an analytical method to determine streptomycin residues in kiwifruit samples using liquid chromatograph tandem mass spectrometer (LC-ESI-MS/MS). Streptomycin residues in samples were extracted using 1% formic acid in methanol, centrifugation for 10 min, and subsequent supernatant filtration. Purified samples were subjected to LC-ESI-MS/MS to confirm presence of and quantify streptomycin residues. Average streptomycin recoveries (6 replicates each sample) were in the range of 94.8%-110.6% with relative standard deviations of <10%. The linearity of the concentration range of 0.01-5.0 mg/kg using a matrix-matched calibration gave R² = 0.9995. The limit of quantification (LOQ) was 0.01 mg/kg. Results showed that our analytical method is rapid, simple, and sensitive, with easy sample preparation.

• Proceedings of the Safety Management and Science Conference
• /
• 2012.11a
• /
• pp.355-368
• /
• 2012

This paper, the hardness of the silicone rubber wire for 50, 60 degrees, 70 degrees High Temperature Vulcanizing (HTV) method using specimens were fabricated. In this paper, in order to investigate the dielectric properties of silicone rubber for wire specimens, the temperature range of $30^{\circ}C{\sim}170^{\circ}C$, the frequency range from 100Hz~4.5MHz report surveyed about the frequency and temperature dependent properties.

• Proceedings of the Safety Management and Science Conference
• /
• 2012.11a
• /
• pp.269-278
• /
• 2012

The purpose of VE (Value Engineering) activities is to come to an achievement of building necessary functions at the lowest possible cost. This study unfolds the co-VE activities which occurred between Gas Range and its partner company in the supply of Grill Body. The co-VE activity has accomplished the cost reduction of about 57 million through performing the function deployment of 12 parts and by devising the alternatives.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.8 no.1
• /
• pp.61-80
• /
• 2002

Since the 1980s, no concepts have been paid more attention to in discussions of environmental policy and natural resource management than ″sustainability″ and ″sustainable development.″ The concepts, however, are still vague and elusive even though they are frequently being used by a wide range of fields including academia. governments, and the private sector. To identify the diversity, range and concepts of sustainability. this paper will conceptualize the theoretical paradigms and social implications of sustainability and will develop general principles in Public policy.

• Proceedings of the Safety Management and Science Conference
• /
• 2011.11a
• /
• pp.551-556
• /
• 2011

This research presents an implementation strategy of Process Capability Index (PCI) according to the types of process characteristics. The types of process feature are classified as four perspectives of variation range, time period, error position, and process stage. The paper examines short-term or long-term PCI, within or between variation, position of precision or accuracy, and inclusion of measurement or calibration stage. Moreover, the study proposes normality test of unilateral PCI.

• Nuclear Engineering and Technology
• /
• v.52 no.11
• /
• pp.2452-2459
• /
• 2020

Neutron spectrum is essential to the safe operation of reactors. Traditional online neutron spectrum measurement methods still have room to improve accuracy for the application cases of wide energy range. From the application of artificial neural network (ANN) algorithm in spectrum unfolding, its accuracy is difficult to be improved for lacking of enough effective training data. In this paper, an adaptive deviation-resistant neutron spectrum unfolding method based on transfer learning was developed. The model of ANN was trained with thousands of neutron spectra generated with Monte Carlo transport calculation to construct a coarse-grained unfolded spectrum. In order to improve the accuracy of the unfolded spectrum, results of the previous ANN model combined with some specific eigenvalues of the current system were put into the dataset for training the deeper ANN model, and fine-grained unfolded spectrum could be achieved through the deeper ANN model. The method could realize accurate spectrum unfolding while maintaining universality, combined with detectors covering wide energy range, it could improve the accuracy of spectrum measurement methods for wide energy range. This method was verified with a fast neutron reactor BN-600. The mean square error (MSE), average relative deviation (ARD) and spectrum quality (Qs) were selected to evaluate the final results and they all demonstrated that the developed method was much more precise than traditional spectrum unfolding methods.

• Journal of Society of Preventive Korean Medicine
• /
• v.20 no.1
• /
• pp.125-144
• /
• 2016

Objectives : About 13% of the medicines used by traditional korean medicines(TKM), are called animal medicines and are derived from non-herbal sources such as animals and insects. However, the clinical use of these preparations from animal medicines is often based on tradition and belief, rather than on evidence of toxicity and efficacy. As a result, animal medicines containing toxin have caused serious problems from injecting patients with venom. Here, various venoms frequently used as TKM were reviewed in terms of their instinct toxity and tried to estimate their safety classification. Methods : The estimation of safety classification was based on human equivalent dose(HED)-based MOS (margin of safety) and clinical dose applied for patients. Results and Conclusions : Except that of snake venom due to no clinical dose, they were evaluated as class 3 for bee venom, class 4 for cantharidin, toxin from blister beetle, and class 1 for venom from scolopendrid. In conclusion, animal medicines showed a wide range of safety classification from class 1 to class 4. This wide range is estimated to result from extremely limited applications of each venom for patients because of their strong toxicity. However, it should be cautious for application in clinics since animal medicines can produce anaphylactic reactions particularly after veinous administration even with a tiny amount of venom.

• Journal of the Korean Society of Safety
• /
• v.27 no.5
• /
• pp.179-184
• /
• 2012

This study was performed to find out the measurement criteria of slip resistance from analysis of human gait and slips. Many kinds of slip resistance testers were developed based on mechanical friction testers. But, there are, as yet, no unambiguous slip resistance measurement methodologies and generally accepted safety criteria or safety thresholds for estimating slipping hazard exposures. Also, there are variety of measuring conditions between those testers. The measurement criteria should be tested within the range of human slipping conditions observed in biomechanical studies. It's results should clearly consider whether the devices reflect the human slipping conditions. In this study a dragsled type friction tester, which was constructed in accordance with ISO 15133 basically, was used. Test conditions were set in order to determine the range of measurement criteria. It is shown that drag velocity should be more than 1 m/s, acceleration be more than 10 $m/s^2$, contact time be less than 0.1sec, and contact pressure be within 350~400 kPa.

• Journal of the Korea Safety Management & Science
• /
• v.17 no.1
• /
• pp.75-84
• /
• 2015

Successful development of weapon systems requires a stringent verification and validation (V&V) process due to the nature of the weapons in which continual increase of operational capability makes the system requirements more complicated to meet. Thus, test and evaluation (T&E) of weapon systems is becoming more difficult. In such a situation, live fire tests appear to be effective and useful methods in not only carrying out V&V of the weapon systems under development, but also increasing the maturity of the end users operability of the system. However, during the process for live fire tests, a variety of accidents or mishaps can happen due to explosion, pyro, separation, and so on. As such, appropriate means to mitigate mishap possibilities should be provided and applied during the live fire tests. To study a way of how to accomplish it is the objective of this paper. To do so, top-level sources of hazard are first identified. A framework for T&E is also described. Then, to enhance the test range safety, it is discussed how test scenarios can be generated. The proposed method is based on the use of the anticipatory failure determination (AFD) and multiple event tree analysis (ETA) in analyzing range safety. It is intended to identify unexpected hazard components even in the environment with constraints. It is therefore expected to reduce accident possibilities as an alternative to the traditional root-cause analysis.