• Journal of Korea Water Resources Association
• /
• v.55 no.2
• /
• pp.111-120
• /
• 2022

The concept of soil moisture memory was used as a method for quantifying the function of soil to control water flow, which evaluates the average residence time of precipitation. In order to characterize the soil moisture memory, a new measurement index called stored precipitation fraction (F_p(f)) was used by tracking the increments in soil moisture by the precipitation event. In this study, the temporal and spatial distribution of soil moisture memory was evaluated along with the slope and soil characteristics of the surface (0~5 cm) soil by using satellite- and model-based precipitation and soil moisture in the Korean peninsula, from 2019 to 2020. The spatial deviation of the soil moisture memory was large as the stored precipitation fraction in the soil decreased preferentially along the mountain range at the beginning (after 3 hours), and the deviation decreased overall after 24 hours. The stored precipitation fraction in the soil clearly decreased as the slope increased, and the effect of drainage of water in the soil according to the composition ratio of the soil particle size was also shown. In addition, average soil moisture contributed to the increase and decrease of hydraulic conductivity, and the rate of rainfall transfer to the depths affected the stored precipitation fraction. It is expected that the results of this study will greatly contribute in clarifying the relationship between soil moisture memory and surface characteristics (slope, soil characteristics) and understanding spatio-temporal variation of soil moisture.

• Journal of Marine Life Science
• /
• v.8 no.1
• /
• pp.68-77
• /
• 2023

In this study, we investigated the quantitative distribution of microplastics in the surface seawater at 8 points near the Taean Peninsula using fluorescence staining. The study revealed a detection range of microplastics from 0 to 360.5 particles/l, with an average of 149.7 ± 46.0 particles/l. When classifying the microplastics by size, it was found that particles smaller than 50 ㎛ were dominant, although there were differences at Site 3. Moreover, it was not possible to identify clear correlations when comparing the number of microplastics based on collection area and particle size. Various physical and chemical factors, including plastic material, dynamic ocean conditions (such as currents, wind, waves, tides), geological characteristics (topography, slope), sediment materials including coastal organisms, human activities (fishing, development, tourism), and weather conditions (floods, rainfall), affect the behavior of microplastics. Therefore, future efforts should focus on standardizing quantitative analysis methods and conducting fundamental research on microplastic monitoring, including the analysis of environmental factors.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.1B
• /
• pp.55-64
• /
• 2008

The evidence of changes in the climate system is obvious in the world. Nevertheless, at the current techniques for flood frequency analysis, the flood distribution can not reflect climate change or long-term climate cycles. Using a linear regression and a Mann-Kendall test, trends in annual maximum precipitation and flood data for several major gauging sites were evaluated. Moreover, this research considered incorporating flood trends by climate change effects in flood frequency analyses. For five rainfall gauging sites (Seoul, Incheon, Ulleungdo, Jeonju, and Gangneung), upward trends were observed in all gauged annual maximum precipitation records but they were not statistically significant. For three streamflow gauging sites (Andong Dam, Soyanggang Dam, and Daecheong Dam), upward trends were also observed in all gauged annual maximum flood records, but only the flood at Andong Dam was statistically significant. A log-normal trend model was introduced to reflect the observed linear trends in annual maximum flood series and applied to estimate flood frequency and risk for Andong Dam and Soyanggang Dam. As results, when the target year was 2005, 50-year floods of the log-normal trend model were 41% and 21% larger then those of a log-normal model for Andong Dam and Soyanggang Dam, respectively. Moreover, the estimated floods of the log-normal trend model increases as the target year increases.

• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.4
• /
• pp.425-437
• /
• 2007

Flow distribution of water and sedimentation rate were investigated to understand the hydrodynamics and settling characteristics of particulate materials in a constructed wetland for treatment of non-point sources pollutants, the Sihwa constructed wetland, Korea. The Sihwa constructed wetland is divided into three sub-wetlands(the Banwol, the Donghwa and the Samhwa wetlands) to treat the polluted water from three streams, the Banwol stream, the Donghwa stream and the Samhwa stream. From the results of water flow experiment using dye(Rhodamine 50WT Red), it was found that the water flow in the wetland was prevailing at the waterway and open water. Dye was spread slowly in the closed water area planted by plants. The mean hydraulic retention time(HRT) at the upper area of high wetland and lower wetland of Banwol, was found to be 34.1 hr at the upper area and 74.6 hr at the lower area respectively, totaling approximately 108.7 hr(4.5 days). The sedimentation rate was higher at lower area(sites of B, C and D) of the wetland than upper area(site of A which is settling zone). Based on the forecast for 20 years as to the amount of sediment that can be deposited in the open water in the future, the sediment depth of each area would be like this: A: 6.3 cm, B: 8.3 cm, C: 7.0 cm, D: 9.5 cm. The contents of organic materials in the sediment deposited within the sediment trap were found to be higher overly in the first investigation period which had much rainfall, and B, C and D areas were found to have an increased COD accumulation than A area. Also, nitrogen and phosphorus were found to increase in the down-stream of the wetland. The results of this study suggest that a sustainable research and management for the characteristics of water flow pattern and sedimentation changeable as time passes is needs to maintain or improve the efficiency of water treatment in the constructed wetland.

• Korean Journal of Environmental Agriculture
• /
• v.30 no.2
• /
• pp.153-159
• /
• 2011

BACKGROUND: This experiment was conducted to investigate the distribution and burden characteristics of heavy metal in the rainwater sampled at Taean area, in the middle part of Korea, from April 2002 to October 2003. METHODS AND RESULTS: The relationship between concentration of heavy metal and other chemical properties in the rainwaters was also evaluated. Chemical properties in the rainwater were various differences with raining periods and years. It appeared that a weighted average pH values of rainwater was ranged from 5.0 to 5.1. Heavy metal concentrations in the rainwater were ranked as Pb > Zn > Cu > Ni > As > Cr > Cd. As compared with heavy metal concentrations of rainwater in 2002, Cu, Pb, and Zn were higher than other elements in 2003. There were positive correlation between major ionic components, such as ${NH_4}^+$, $Ca^{2+}$, $Mg^{2+}$, $K^+$, $Na^+$, ${SO_4}^{2-}$ and ${NO_3}^-$, and As, Cd, Zn, Cr, and Ni concentrations in rainwater. For heavy metal distribution of rainwater, the order of average enrichment factor was Cd > Pb > As > Cu > Zn > Ni > Cr, and these were relatively higher than the natural components such as Fe, Mg and Ca. The monthly enrichment factor were relatively high, from August to October at Taean. The monthly amount of heavy metal precipitation was high in the rainy season from July to August because of great influence of rainfall. CONCLUSION(s): The results of this study suggest that the heavy metals(Cd, Pb, As, Cu, and Zn) of rainwater is strongly influenced by anthropogenic sources rather than natural sources.

• Geotechnical Engineering
• /
• v.2 no.1
• /
• pp.27-44
• /
• 1986

The measured soil data are analyzed to the descriptive statistics and classified into the four models of uncorrelated-normal (UNNO), uncorrelated-nonnormal (VNNN), correlatedonnormal(CONN), and correlated-nonnormal(CONN) . This paper presents the comparisons of reliability index and check points using the advanced first-order second-moment method with respect to the four models as well as BASIC Program. A sin91e-mode Performance function is consisted of the basic design variables of bearing capacity and settlements on shallow foundations and input the above analyzed soil informations. The main conclusions obtained in this study are summarized as follows: 1. In the bearing capacity mode, cohesion and bearing-capacity factors by C-U test are accepted for normal and lognormal distribution, respectively, and negatively low correlated to each other. Since the reliability index of the CONN model is the lowest one of the four model, which could be recommended a reliability.based design, whereas the other model might overestimate the geotechnical conditions. 2. In the case of settlements mode, the virgin compression ratio and preccnsolidation pressure are fitted for normal and lognormal distribution, respectively. Constraining settlements to the lower ones computed by deterministic method, The CONN model is the lowest reliability of the four models.

• Korean Journal of Remote Sensing
• /
• v.26 no.2
• /
• pp.65-73
• /
• 2010

To observe and analyze the characteristics of cloud and precipitation properties, the Cloud physics Observation System (CPOS) has been operated from December 2003 at Daegwallyeong ($37.4^{\circ}N$, $128.4^{\circ}E$, 842 m) in the Taebaek Mountains. The major instruments of CPOS are follows: Forward Scattering Spectrometer Probe (FSSP), Optical Particle Counter (OPC), Visibility Sensor (VS), PARSIVEL disdrometer, Microwave Radiometer (MWR), and Micro Rain Radar (MRR). The former four instruments (FSSP, OPC, visibility sensor, and PARSIVEL) are for the observation and analysis of characteristics of the ground cloud (fog) and precipitation, and the others are for the vertical cloud characteristics (http://weamod.metri.re.kr) in real time. For verification of CPOS products, the comparison between the instrumental products has been conducted: the qualitative size distributions of FSSP and OPC during the hygroscopic seeding experiments, the precipitable water vapors of MWR and radiosonde, and the rainfall rates of the PARSIVEL(or MRR) and rain gauge. Most of comparisons show a good agreement with the correlation coefficient more than 0.7. These reliable CPOS products will be useful for the cloud-related studies such as the cloud-aerosol indirect effect or cloud seeding. The visibility value is derived from the droplet size distribution of FSSP. The derived FSSP visibility shows the constant overestimation by 1.7 to 1.9 times compared with the values of two visibility sensors (SVS (Sentry Visibility Sensor) and PWD22 (Present Weather Detect 22)). We believe this bias is come from the limitation of the droplet size range ($2{\sim}47\;{\mu}m$) measured by FSSP. Further studies are needed after introducing new instruments with other ranges.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.22 no.3
• /
• pp.21-36
• /
• 2019

Dead fuel moisture content is a key variable in fire danger rating as it affects fire ignition and behavior. This study evaluates simple regression models estimating the moisture content of standardized 10-h fuel stick (10-h FMC) at three sites with different characteristics(urban and outside/inside the forest). Equilibrium moisture content (EMC) was used as an independent variable, and in-situ measured 10-h FMC was used as a dependent variable and validation data. 10-h FMC spatial distribution maps were created for dates with the most frequent fire occurrence during 2013-2018. Also, 10-h FMC values of the dates were analyzed to investigate under which 10-h FMC condition forest fire is likely to occur. As the results, fitted equations could explain considerable part of the variance in 10-h FMC (62~78%). Compared to the validation data, the models performed well with R2 ranged from 0.53 to 0.68, root mean squared error (RMSE) ranged from 2.52% to 3.43%, and bias ranged from -0.41% to 1.10%. When the 10-h FMC model fitted for one site was applied to the other sites, $R^2$ was maintained as the same while RMSE and bias increased up to 5.13% and 3.68%, respectively. The major deficiency of the 10-h FMC model was that it poorly caught the difference in the drying process after rainfall between 10-h FMC and EMC. From the analysis of 10-h FMC during the dates fire occurred, more than 70% of the fires occurred under a 10-h FMC condition of less than 10.5%. Overall, the present study suggested a simple model estimating 10-h FMC with acceptable performance. Applying the 10-h FMC model to the automatic mountain weather observation system was successfully tested to produce a national-scale 10-h FMC spatial distribution map. This data will be fundamental information for forest fire research, and will support the policy maker.

• Korean Journal of Remote Sensing
• /
• v.39 no.2
• /
• pp.193-205
• /
• 2023

A large amount of floating debris from land-based sources during heavy rainfall has negative social, economic, and environmental impacts, but there is a lack of monitoring systems for floating debris accumulation areas and amounts. With the recent development of artificial intelligence technology, there is a need to quickly and efficiently study large areas of water systems using drone imagery and deep learning-based object detection models. In this study, we acquired various images as well as drone images and trained with You Only Look Once (YOLO)v5s and the recently developed YOLO7 and YOLOv8s to compare the performance of each model to propose an efficient detection technique for land-based floating debris. The qualitative performance evaluation of each model showed that all three models are good at detecting floating debris under normal circumstances, but the YOLOv8s model missed or duplicated objects when the image was overexposed or the water surface was highly reflective of sunlight. The quantitative performance evaluation showed that YOLOv7 had the best performance with a mean Average Precision (intersection over union, IoU 0.5) of 0.940, which was better than YOLOv5s (0.922) and YOLOv8s (0.922). As a result of generating distortion in the color and high-frequency components to compare the performance of models according to data quality, the performance degradation of the YOLOv8s model was the most obvious, and the YOLOv7 model showed the lowest performance degradation. This study confirms that the YOLOv7 model is more robust than the YOLOv5s and YOLOv8s models in detecting land-based floating debris. The deep learning-based floating debris detection technique proposed in this study can identify the spatial distribution of floating debris by category, which can contribute to the planning of future cleanup work.

• Journal of the Korean Society of Food Culture
• /
• v.1 no.2
• /
• pp.116-126
• /
• 1986

This study was designed to be a link in the chain of the investigation on daily life and consciousness of longevous people in Korea, and to investigate the regional feature of longevity areas. The daily life and consciousness were investigated on 379 subjects(male 121, female 258) of the aged who were above 80 years of age, from June to November in 1985. This paper is to report the results investigated the longevity rate, distribution, classification and weather of longevity districts, and also the actual conditions such as the functions of daily life and educational degree of longevous people. 1. The number of longevous people in Korea was 171,449 (male 42,842, female 128,607), and the average longevity rate was 0.46% against total population in Korea(male 0.23%, female 0.69%). 2. Of the longevity rates of shi and/or do in Korea, Cheju(1.03%) was the highest among these districts, and decreased in the order of Chonnam(0.79%), Chonbuk(0.66%), Kyongbuk(0.65%) and Kyongnam(0.61%), whereas the large cities such as Inchon(0.22%), Seoul(0.23%), Pusan(0.23%) and Taegu(0.28%) were remarkably lower than districts in seasides and mountains. 3. The districts above 1.0% of longevity rate in Korea showed 17-guns, and the distribution of these districts was 10-guns of Chonnam, 2-guns of Kyongbuk and Kyongnam, and 1-gun of Kyonggi, Cho-nbuk and Cheju, respectively. 4. Of these districts, Pukcheju(1.65%) was the highest, and decreased in the order of Namhae(1.56%), Sungju(1.24%), Posong(1.22%) and Koksong(1.20%). The highest figure(male 0.71%, female 2.51%) was observed in Pukcheju as contrasted with 0.23%(male) and 0.69%(female) of the average longevity rate in Korea. 5. The sex ratio of longevous people in Korea showed the female/male ratio of 3.0. It is, therefore, believed that the longevity rate of female was 3 times higher than that of male. 6. The longevity districts were classified into seven districts in seasides, three districts in isolated islands, and seven rural districts in mountains. 7. The situation of weather in longevity districts was in the range of 11.2 to $14.8^{\circ}C$ at annual average temperature, and 878.5 to 1585.9mm at annual average rainfall. 8. Of the educational degree of longevous people, uneducated(71.5%) was the highest, and followed by the order of village school(15.8%) and above elementary school(4.8%). 9. In the functions of daily life, the aged moving actively(53.0%) was the highest among these longevous people, followed by the aged moving a little(23.5%). Therefore, it is believed that health degree of these longevous peoples by the functions of daily life was very gratifying.