• 한국정밀공학회지
• /
• 제28권4호
• /
• pp.427-435
• /
• 2011

This paper deals with the measurement and analysis of the squeal noise according to the curvature of rail. The squeal noise is generated by the friction between the railway with curve and the wheel. The squeal noise is a big problem in Busan Metro Line 3. If the developing panel type ANC(Active Noise Control) system which is attached to the floor can reduce 5 dB in below 500 Hz, the sound pressure level of the whole band pass can be reduced about 4-4.8 dB in squeal noise above the curvature of R400. Curve squeal noise is the intense high frequency tonal that can occur when a railway vehicle transverses a curve. The frequency range is from around 500 to almost 20,000 Hz, with noise levels up to about 15 dB in curve.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.2163-2172
• /
• 2008

The noise to be considered as the most important in railway systems is the noise generated from the wheel/rail interaction. Such noise can be divided into three categories; that is, the rolling noise, the squeal noise and the wheel howling noise. Especially in metro systems, this type of noise has been considered seriously in recent years, and the diversified studies on the mechanism and solutions of such noise are in progress by many railways and researching bodies. In this study, a specially designed wheel absorber is installed in the wheel, and FEM analysis and laboratory tests are executed for the two cases, i.e. with wheel absorber and without wheel absorber, to check the effect of the wheel absorber in noise reduction. For the FEM analysis, the frequency response functions for respective cases are compared. And, for the laboratory test, following four cases are tested and compared; that is, i) with wheel only, ii) installation of ring damper only, iii) installation of damping material and cover, iv) installation of complete absorber system.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 추계학술대회 논문집
• /
• pp.401-402
• /
• 2012

• 복합신소재구조학회지
• /
• 제4권1호
• /
• pp.28-32
• /
• 2013

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 춘계학술대회 논문집
• /
• pp.613-618
• /
• 2004

Is confirming safety of derailment when wish to develop new vehicles or upgrade running speed of vehicles. This means the measure of wheel load and lateral force that act between wheel and rail. So far, problem in continuous measuring method of derailment coefficient was sensitivity decline and noise growth. This research supplemented these problems by composition of new bridge circuit.

• 한국철도학회논문집
• /
• 제12권3호
• /
• pp.329-334
• /
• 2009

지하철은 지상교통과 비교하여 정확성, 신속성, 안전성, 대량성외에도 배기가스 배출이 없다는 이점 때문에 대도시 교통 문제 해결을 위한 유용한 수송 수단이 되고 있다. 그러나 콘크리트 도상에 의한 터널 구조로 객실내 소음이 사회적으로 문제가 되고 있다. 이에 객실 소음을 분석하기 위하여 임시열차 운행을 통하여 실측 된 결과를 토대로 소음의 경로와 위치별 소음의 특성을 분석하였다. 객실내 소음 저감을 위해서는 차량측면은 저주파 대역을 차량 바닥은 중대역구간의 소음 대비책을 강구 하여야 하며, 차량의 투과 손실 향상 및 차체의 기밀을 유지하는 것이 필요하다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1995년도 추계학술대회논문집; 한국종합전시장, 24 Nov. 1995
• /
• pp.197-200
• /
• 1995

Corrugation of railway track can be caused by the various dynamic behavior of travelling wheels and track. In this paper, the coupled vibrations of travelling wheel and railway track are analyzed as the cause of corrugations. To analyze the coupled vibrations, the track supported by the sleepers and the traveling wheel are identified to the elastically supported infinite beam and the spring-mass system which runs at constant speed. The Hertzian contact spring is considered betwen the infinite beam and spring-mass system. The dynamic responses of elastically supported infinite beam and spring-mass system are calculated. The cause and development of rail corrugation are discussed in the view point of contact force fluctuation affected by the elastic supports and the corrugated surface profile of the track. By the obtained results, the possibilities of resonance are checked between the excitation by the corrugated surface profile and the natural frequency of contact spring-moving mass system. It may be thought to a development of railway corrugation.

• 한국소음진동공학회논문집
• /
• 제25권9호
• /
• pp.620-627
• /
• 2015

Long continuous bridge deck can become contracted considerably as temperature drops, which can lead to a large expansion of sleeper span at the end of it. Since this huge sleeper span then can cause problems both with safety of train operation and structural stability of tracks, it is necessary to take the issue into consideration systematically in the designing process of the bridge. In this paper, an evaluation process through the analysis of train-track interaction was presented which can basically review the effects of the expansion of sleeper span at the end of long continuous bridge deck on the safety of the train and the structural stability of the track. The analyses of the interaction between the light rail train and tracks were carried out targeting the sleeper span as a main parameter. The safety of train operation and structural stability of tracks in a light rail system due to the expansion of the sleeper span were evaluated by comparing the numerical results with the related criteria.

• 센서학회지
• /
• 제26권5호
• /
• pp.342-347
• /
• 2017

We present a precision instrument amplifier (IA) designed for bio-potential acquisition. The proposed IA employs a capacitively coupled instrument amplifier (CCIA) structure to achieve a rail-to-rail input common-mode range and low gain error. A positive feedback loop is applied to boost the input impedance. Also, DC servo loop (DSL) with pseudo resistors is adopted to suppress electrode offset for bio-potential sensing. The proposed amplifier was designed in a $0.18{\mu}m$ CMOS technology with 1.8V supply voltage. Simulation results show the integrated noise of $1.276{\mu}Vrms$ in a frequency range from 0.01 Hz to 1 KHz, 65dB SNR, 118dB CMRR, and $58M{\Omega}$ input impedance respectively. The total current of IA is $38{\mu}A$. It occupies $740{\mu}m$ by $1300{\mu}m$ including the passive on-chip low pass filter.

• 한국소음진동공학회논문집
• /
• 제22권11호
• /
• pp.1064-1070
• /
• 2012

This paper analyzes the pitting's cause of elevator's worm gear type traction machine. To find a cause of pitting problem, we analyzed vibration, a proper design allowance and lubrication. We brought a conclusion that the cause of pitting is not a simple vibration problem, such as misalignment of worm reducer and rail, but mostly related to a designed allowance. In this case, the allowance is tight. In general, the allowance of traction machine and lubrication is varied by manufacturers. When the allowance is tight, a proper lubrication can diminish the pitting problem.