• JSTS:Journal of Semiconductor Technology and Science
• /
• 제11권4호
• /
• pp.295-301
• /
• 2011

A triple-band transceiver module for 2.3/2.5/3.5 GHz mobile WiMAX, IEEE 802.16e, applications is introduced. The suggested transceiver module consists of RFIC, reconfigurable/multi-resonance MIMO antenna, embedded PCB, mobile WiMAX base band, memory and channel selection front-end module. The RFIC is fabricated in $0.13{\mu}m$ RF CMOS process and has 3.5 dB noise figure(NF) of receiver and 1 dBm maximum power of transmitter with 68-pin QFN package, $8{\times}8\;mm^2$ area. The area reduction of transceiver module is achieved by using embedded PCB which decreases area by 9% of the area of transceiver module with normal PCB. The developed triple-band mobile WiMAX transceiver module is tested by performing radio conformance test(RCT) and measuring carrier to interference plus noise ratio (CINR) and received signal strength indication (RSSI) in each 2.3/2.5/3.5 GHz frequency.

• ETRI Journal
• /
• 제26권3호
• /
• pp.229-240
• /
• 2004

This paper reports on our development of a dual-mode transceiver for a CMOS high-rate Bluetooth system-onchip solution. The transceiver includes most of the radio building blocks such as an active complex filter, a Gaussian frequency shift keying (GFSK) demodulator, a variable gain amplifier (VGA), a dc offset cancellation circuit, a quadrature local oscillator (LO) generator, and an RF front-end. It is designed for both the normal-rate Bluetooth with an instantaneous bit rate of 1 Mb/s and the high-rate Bluetooth of up to 12 Mb/s. The receiver employs a dualconversion combined with a baseband dual-path architecture for resolving many problems such as flicker noise, dc offset, and power consumption of the dual-mode system. The transceiver requires none of the external image-rejection and intermediate frequency (IF) channel filters by using an LO of 1.6 GHz and the fifth order onchip filters. The chip is fabricated on a $6.5-mm^{2}$ die using a standard $0.25-{\mu}m$ CMOS technology. Experimental results show an in-band image-rejection ratio of 40 dB, an IIP3 of -5 dBm, and a sensitivity of -77 dBm for the Bluetooth mode when the losses from the external components are compensated. It consumes 42 mA in receive ${\pi}/4-diffrential$ quadrature phase-shift keying $({\pi}/4-DQPSK)$ mode of 8 Mb/s, 35 mA in receive GFSK mode of 1 Mb/s, and 32 mA in transmit mode from a 2.5-V supply. These results indicate that the architecture and circuits are adaptable to the implementation of a low-cost, multi-mode, high-speed wireless personal area network.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제9권12호
• /
• pp.5015-5027
• /
• 2015

Transceiver optimization in multiple input multiple output (MIMO) cognitive systems is studied in this paper. The joint transceiver beamformer design is introduced to minimize the transmit power at secondary base station (SBS) while simultaneously controlling the interference to primary users (PUs) and satisfying the secondary users (SUs) signal-to-interference-plus-noise ratio (SINR) based on the convex optimization method. Due to the limited cooperation between SBS and PUs, the channel state information (CSI) usually cannot be obtained perfectly at the SBS in cognitive system. In this study, both perfect and imperfect CSI scenarios are considered in the beamformer design, and the proposed method is robust to CSI error. Numerical results validate the effectiveness of the proposed algorithm.

• 정보와 통신
• /
• 제24권3호
• /
• pp.76-86
• /
• 2007

This paper describes the RF performance issues of UE RF Transceiver for W-CDMA system based on 3GPP specifications. the parameters of transmitter and receiver are derived from the viewpoint of RF performance. In order for UE to achieve high performance, the transceiver performance requirements such as ACIR, EVM, Peak Code Domain Error, spectrum emission mask, frequency error stability and TX power control dynamic range for transmitter and reference sensitivity level, blocking characteristics, noise figure, ACS, linearity, AGC dynamic range for receiver are considered. On the basis of the required parameters, the UE RF transceiver is designed and then implemented. The evaluation of RF performance is accomplished through practical test scenarios.

• 디지털산업정보학회논문지
• /
• 제14권4호
• /
• pp.93-99
• /
• 2018

This paper presents an implementation method using NDK (Network Developer's Kit) of GNU (GNU is Not Unix) Radio and Multicore DSP (Digital Signal Processor) to implement LTE (Long Term Evolution) SDR (Software Defined Radio) Platform. In order to satisfy 1.4MHz, 3MHz, 5MHz and 10MHz of the bandwidth supported by LTE, USRP (Universal Software Radio Peripheral) X series which is an RF (Radio Frequency) transceiver of Ettus Research was used. To control this, GNU Radio which is an open source software radio toolkit was used. We also used NDK from TI (Texas Instruments) DSP to transfer data between USRP and DSP. Experimental results show throughput results according to each bandwidth, thus confirming the feasibility of implementing LTE SDR Platform using GNU Radio and NDK of TI DSP.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 하계종합학술대회 논문집(5)
• /
• pp.187-190
• /
• 2000

We presents the construction of radio frequency pad area array package modules which operate at radio frequency of 224MHz, and proposes the structure of RF module packages to improve its electrical characteristics. The module of RF PAA package was constructed in the configuration of three dimensional stacked package and reduced size. RF PAA packages showed the optimized and improved gain of 2dB by partitioning the RF transceiver with 3 dimensional stacked PAA packages.

• ETRI Journal
• /
• 제19권3호
• /
• pp.116-140
• /
• 1997

The base station transceiver subsystem (BTS) of the CDMA Mobile System is interfaced to mobile stations over the air and to the wired network through a packet switched interconnection network. The potential benefits of CDMA technology are achieved when the transmitter and the receiver are properly designed and implemented. The physical layer of the interface at the base station is implemented with the CDMA ASICs and control circuits in channel card of the BTS. We present the design perspectives and structural illustration of the BTS. Base station modem ASICs and their control to implement the CDMA receiver, Baseband and RF signal processing blocks, and BTS controller are described. Elaborate power control is essential to ensure the high capacity which is one of advantages of the CDMA technology. The closed loop reverse link power control and the forward link power control operated in the BTS are described.

• 제어로봇시스템학회논문지
• /
• 제12권5호
• /
• pp.438-443
• /
• 2006

In this paper, We had proposed SDR module, and designed FPGA to compose with channel separation of broadband CDMA signal what have multiple FA. At decomposition and composition process of multiple FA CDMA signal, system only progress decomposition and composition of channel selected by software. Therefore, proposed system can manage base station transceiver system very effectively than the other way what send on all band of multiple CDMA signal. Also, it is possible that system sets again coefficient of each filter because it is consisted of SDR module. Therefore, we can easily control coefficient each filter according to base station transceiver system environment.

• 대한임베디드공학회논문지
• /
• 제4권1호
• /
• pp.16-22
• /
• 2009

This paper aims at designing an impulse-radio ultra-wideband (IR-UWB) transceiver, especially targeting the IEEE 802.15.4a indoor ranging and communication systems. We first investigate the IEEE 802.15.4a IR-UWB signals and suggest the full-digital transceiver architecture accordingly. Since the wireless systems equipped with the impulse signal have the property of low-duty cycle, i.e., discontinuity in time, while the conventional systems takes the continuous signals, it is required to reconfigure the system design, including link budget. Following brief introduction to our IEEE 802.15.4a IR-UWB system hardware, we finally examine the ranging performance in indoor environments to verify our system design.

• ETRI Journal
• /
• 제40권2호
• /
• pp.167-179
• /
• 2018

This paper proposes an IEEE 802.15.4m compliant TV white-space orthogonal frequency-division multiplexing (TVWS)-(OFDM) radio frequency (RF) transceiver that can be adopted in advanced metering infrastructures, universal remote controllers, smart factories, consumer electronics, and other areas. The proposed TVWS-OFDM RF transceiver consists of a receiver, a transmitter, a 25% duty-cycle local oscillator generator, and a delta-sigma fractional-N phase-locked loop. In the TV band from 470 MHz to 698 MHz, the highly linear RF transmitter protects the occupied TV signals, and the high-Q filtering RF receiver is tolerable to in-band interferers as strong as -20 dBm at a 3-MHz offset. The proposed TVWS-OFDM RF transceiver is fabricated using a $0.13-{\mu}m$ CMOS process, and consumes 47 mA in the Tx mode and 35 mA in the Rx mode. The fabricated chip shows a Tx average power of 0 dBm with an error-vector-magnitude of < 3%, and a sensitivity level of -103 dBm with a packet-error-rate of < 3%. Using the implemented TVWS-OFDM modules, a public demonstration of electricity metering was successfully carried out.