• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2360-2365
• /
• 2007

A new microemitter (microcombustor) configuration for a micro thermophotovoltaic system in which thermal energy is directly converted into electrical energy through thermal radiation was investigated experimentally and computationally. The microemitter as a thermal heat source was designed for a few watt power-generating micro thermophotovoltaic system. In order to satisfy the primary requirements for designing the microemitter, i.e., stable burning in the small confinement and maximum heat transfer through the emitting walls but uniform distribution of temperature along the walls, the present microemitter is cylindrical with an annular-type shield for heat recirculation to apply for the excessive enthalpy concept. Results show that the heat recirculation substantially improves the performance of the microemitter: the observed and predicted thermal radiation from the microemitter walls indicated that heat generated in the microemitter is uniformly emitted.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.5 no.4
• /
• pp.295-305
• /
• 1993

Thermal performance of test cell of model hot water Ondol house was simulated by equivalence heat resistence and heat capacity method. In this method wall was replaced by two equivalence and one heat capacity. This method enables to simulate the variation of temperature of each element of model house. The effect of pipe diameter, pitch of pipe and with or without consideration of inter-radiation between wall surfaces on the energy consumption rate were investgated. Results show that radiations between the ground surface of room and wall surfaces contribute to the heating of room air by reducing the convection heat loss through the wall surfaces.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.569-572
• /
• 2003

In VLM-ST process, the fine detailed shape processing process is needed due to the use of thick sheets for layers. The developed process perform the fine detailed shape processing in VLM-ST parts using non-contact hot tool. To predict the heat-affected zone and temperature distribution of VLM-ST parts in detailed shaping, the heat flux from the tool to the surface was calculated for the finite element analysis by modeling the tool as a heat source of radiation. The dominant process parameters such as the radiated heat input, the tool speed, and the gap between the tool tip and the foam sheet (tool height) were considered in the analysis. The results showed a good agreement with the experiments.

• Journal of the Korean Society of Visualization
• /
• v.14 no.2
• /
• pp.25-30
• /
• 2016

The wafer temperature and its uniformity inside the LPCVD chamber were analyzed. The temperature uniformity at the end of the wafer load depends on the heat-insulating cap. The finite difference method was used to investigate the radiation and conduction heat transfer mechanisms, and the temperature field and heat diffusion in the LPCVD chamber was visualized. It was found that the temperature uniformity of the wafers could be controlled by the size and distance of the heat-insulating cap.

• Journal of Biosystems Engineering
• /
• v.31 no.5 s.118
• /
• pp.395-402
• /
• 2006

Mixed heat transfer in an indirected NIR (Near Infrared Ray) dry chamber was investigated numerical analysis. It is Important that the miked heat transfer effects on double parameters which the Reynolds number and the position of emit lamp. Reynolds number are based on the outer diameter of the cylinder range from 103 to $30{\times}105$. Four difference heat transfer regimes of behavior are apparent: forced convection and radiation on the outer surface of the cylinder, pure conduction, pure natural convection and radiation between lamp surface and inner surface of the cylinder. The temperature and flow patterns are illustrated by iso-contour lines for the double parameters. Also presented are results on the convective heat transfer flux and the radiative heat transfer flux as increased with Reynolds number.

• Proceedings of the KSRS Conference
• /
• 2008.10a
• /
• pp.68-71
• /
• 2008

Our goal is to obtain a better scientific understanding how to define the nature and role of remotely sensed land surface parameters and energy fluxes in the heat island phenomena, and local and regional weather and climate. By using the MODIS visible and thermal imagery data and analyzing the surface energy flux images associated with the change of the landcover and landuse in study area, we will estimate and present how significant is the magnitude of the heat island heat effect and its relation with the surface parameters and the energy fluxes in Taiwan. To achieve our objective, we used the energy budget components such as net radiation, soil heat flux, sensible heat flux, and latent heat flux in the study area of interest derived form remotely sensed data to understand the island heat effect. The result shows that the water is the most important component to decrease the temperature, and the more the consumed net radiation to latent heat, the lower urban surface temperature.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.8 no.4
• /
• pp.561-575
• /
• 1996

The interaction of turbulent mixed convection and surface radiation in a three-dimensional channel with the heated blocks is analyzed numerically. Two blocks are maintained at high temperature and the other bottom and horizontal walls are insulated. S-4 method is employed to calculate the effect of the radiative heat transfer. The low Reynolds number k-$\varepsilon$ model proposed by Launder and Sharma is used to estimate the turbulent influence on the heat transfer enhancement. From above modeling, the effects of various channel specifications on the flow and heat transfer characteristics are investigated. The variables used for the present study are Reynolds number, block spacing, the channel height spacing for block and the emissivity. Average Nusselt numbers along the block surfaces are correlated and presented in terms of Reynolds number, emissivity and dimensionless geometric parameters. For the range of conditions in this study, average Nusselt numbers along the block surfaces are strongly influenced by the Reynolds numbers and channel height spacing for block but weakly influenced by the block spacing and the emissivity of the adiabatic walls.

• Journal of Environmental Science International
• /
• v.24 no.10
• /
• pp.1265-1272
• /
• 2015

To investigate the thermal environment over the summertime asphalt pavements, an automatic weather observation system was installed at a parking lot paved with asphalt to observe various meteorological parameters and surface temperature from July 1 to September 30, 2014. Since the number of rainy days in summer of 2014 particularly after the mid July is more than that of average data, a ratio of daily peak surface temperature above $45^{\circ}C$ was 28% which was lower than the average. The observational data about hourly average surface temperature and various heat balance factors at days where daily peak surface temperature is above $45^{\circ}C$ are as follows: An hour that had the daily maximum temperature was around 15 pm and the value was $49^{\circ}C$ approximately. Net shortwave radiation was the highest at 12pm as $800W/m^2$ and much radiation of $500W/m^2$ was absorbed at the ground between 11am and 17pm. Sensible heat that was delivered from the ground to the atmosphere was evaluated as $200W/m^2$ between 10am and 19pm. underground transfer heat up to $100W/m^2$ was measured as negative from 19pm to the next day 8am, which indicated the lower atmosphere was heated at night.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.8
• /
• pp.2681-2692
• /
• 1996

The finite-volume method for radiation in a three-dimensional non-orthogonal gas turbine combustion chamber with absorbing, emitting and anisotropically scattering medium is presented. The governing radiative transfer equation and its discretization equation using the step scheme are examined, while geometric relations which transform the Cartesian coordinate to a general body-fitted coordinate are provided to close the finite-volume formulation. The scattering phase function is modeled by a Legendre polynomial series. After a benchmark solution for three-dimensional rectangular combustor is obtained to validate the present formulation, a problem in three-dimensional non-orthogonal gas turbine combustor is investigated by changing such parameters as scattering albedo, scattering phase function and optical thickness. Heat flux in case of isotropic scattering is the same as that of non-scattering with specified heat generation in the medium. Forward scattering is found to produce higher radiative heat flux at hot and cold wall than backward scattering and optical thickness is also shown to play an important role in the problem. Results show that finite-volume method for radiation works well in orthogonal and non-orthogonal systems.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.2 no.1
• /
• pp.1-9
• /
• 1992

Radiation heat transfer was calculated for initial stage of crystal growth in Czochralski crystal growth system. View factors among surface elements were calculated for the estimation of heat evolution and all the surfaces were assumed to be diffuse-gray. The values of view factors were greatly different along the position of surface elements. The dissipated amounts of heat flux from the melt surface were 3.6 times larger than those from the crystal surface at the initial stage of crystal growth and this amounts were greater when the surface elements were not considered. The trijunction part of the crystal was greatly affected by the melt surface near the crystal. Consequently radiation heat transfer between surface elements must be considered in order to correctly simulate the initial crystal growth.