• Journal of the Korea Concrete Institute
• /
• v.20 no.2
• /
• pp.165-173
• /
• 2008

One of the most important requirements for reinforced concrete constructions is the bond behavior between concrete and reinforcement. For practical application, it is very important to study bond behavior of reinforcing bars in recycled aggregate concrete (RAC). Thirty six pull-out tests were carried out in order to investigate the bond behaviour between recycled coarse aggregate concrete (RCAC) and deformed bars. RCA replacement ratios (i.e., 0%, 30%, 60% and 100%) and positions of deformed bar (i.e., vertical and horizontal position) were considered as variables in this paper. Each specimen was in the form of a cube, with edges of 150 mm in length and for the pull-out tests, a deformed bar, 13 mm in diameter, was embedded in the center of each specimen. Based on the test results, the bond strength between the RCAC and deformed bars were influenced by both RCA replacement ratios and positions of deformed bars. It was found that under the equivalent mix proportion (i.e., the mix proportions are the same, except for different RCA replacement ratios), the bond strength between the RCAC and the ribbed bar has no obvious relation with the RCA replacement ratio, whereas the positions of deformed bars have a significant effect on the bond behavior between the RCAC and deformed bars. Under the condition of same RCA replacement ratio, the specimen of horizontal reinforcement at upper position (HU type) appear considerably low bond stress.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.24 no.1
• /
• pp.22-28
• /
• 2004

Since the used materials of furnace heater tube with different kinds of thermal degradation were not commonly available, the HK-40 steel specimens were heat-treated isothermally at elevated temperature to simulate the microstructure at the service temperature. HK-40 steel specimens with five different aging time were prepared by isothermal heat treatment at $1050^{\circ}C$. The characteristics of the magnetic susceptibility have been investigated for the degradation evaluation of HK-40 steel. The magnetic susceptibility at room temperature increases as the extent of degradation of the materials increases. The variation of magnetic susceptibility was compared with the variation of tensile properties and Vickers hardness. To investigate the effect of the microsturctural change on the characteristics of tensile properties, hardness and magnetic susceptibility, the microstructures were examined by a scanning electron microscope(SEM) and the chemical compositions were analyzed by a energy spectrometer of SEM. As a result, the magnetic susceptibility method can be suggested as one of the nondestructive evaluation methods for the degradation of the HK-40 steel.

• Korean Chemical Engineering Research
• /
• v.60 no.2
• /
• pp.229-236
• /
• 2022

An experimental investigation was conducted on the influences of median size, dust concentration, dust condition (cloud and layer) for the fire and explosion hazard assessment of dusts with the same powder property. For this purpose, tests have been performed in accordance with 20 L explosion sphere, thermogravi- metric analyze, combustion rate tester (UN method). We investigated the explosion characteristics and flame propagation velocity (FPV) in dust cloud and the flame spread velocity(FSV) over dust layer on 8 dust samples with different particle sizes of 4 types of dusts (Sugar, Mg, Al, Zr). An explosion hazard increased with decreasing particle size in Mg and Al dust clouds, but sugar did not show the effect of explosion hazard due to particle size change in dust clouds. The flame propagation velocity (FPV) of suspended dusts increased significantly when the particle size decreased from micro to nano than the variation of particle size in micro range. The flame spread velocity (FSV) over dust layer showed a tendency to increase over the inclined dust layers (30° slope) rather than the horizontal dust layers (0° slope). The flame spread rate (FSV) over dust layers increased on the inclined dust layer (30° slope) rather than the horizontal dust layer (0° slope) and was higher upward flame than the downward flame in condition of inclined dust layers(30° slope).

• Structural Engineering and Mechanics
• /
• v.83 no.3
• /
• pp.305-326
• /
• 2022

To realize the recycling utilization of waste concrete and alleviate the shortage of resources, 11 specimens of steel reinforced recycled concrete (SRRC) filled circular steel tube columns were designed and manufactured in this study, and the cyclic loading tests on the specimens of columns were also carried out respectively. The hysteretic curves, skeleton curves and performance indicators of columns were obtained and analysed in detail. Besides, the finite element model of columns was established through OpenSees software, which considered the adverse effect of recycled coarse aggregate (RA) replacement rates and the constraint effect of circular steel tube on internal RAC. The numerical calculation curves of columns are in good agreement with the experimental curves, which shows that the numerical model is relatively reasonable. On this basis, a series of nonlinear parameters analysis on the hysteretic behaviors of columns were also investigated. The results are as follows: When the replacement rates of RA increases from 0 to 100%, the peak loads of columns decreases by 7.78% and the ductility decreases slightly. With the increase of axial compression ratio, the bearing capacity of columns increases first and then decreases, but the ductility of columns decreases rapidly. Increasing the wall thickness of circular steel tube is very profitable to improve the bearing capacity and ductility of columns. When the section steel ratio increases from 5.54% to 9.99%, although the bearing capacity of columns is improved, it has no obvious contribution to improve the ductility of columns. With the decrease of shear span ratio, the bearing capacity of columns increases obviously, but the ductility decreases, and the failure mode of columns develops into brittle shear failure. Therefore, in the engineering design of columns, the situation of small shear span ratio (i.e., short columns) should be avoided as far as possible. Based on this, the calculation model on the skeleton curves of columns was established by the theoretical analysis and fitting method, so as to determine the main characteristic points in the model. The effectiveness of skeleton curve model is verified by comparing with the test skeleton curves.

• Earthquakes and Structures
• /
• v.23 no.5
• /
• pp.445-462
• /
• 2022

To investigate and evaluate the seismic damage behaviors of steel reinforced recycled concrete (SRRC) filled circular steel tube composite columns, in this study, the cyclic loading tests of 11 composite columns was carried out by using the load-displacement joint control method. The seismic damage process, hysteretic curves and performance indexes of composite columns were observed and obtained. The effects of replacement rates of recycled coarse aggregate (RCA), diameter thickness ratio, axial compression ratio, profile steel ratio and section form of profile steel on the seismic damage behaviors of composite columns were also analyzed in detail. The results show that the failure model of columns is a typical bending failure under the combined action of horizontal loads and vertical loads, and the columns have good energy dissipation capacity and ductility. In addition, the replacement rates of RCA have a certain adverse effect on the seismic bearing capacity, energy consumption and ductility of columns. The seismic damage characteristics of composite columns are revealed according to the failure modes and hysteretic curves. A modified Park-Ang seismic damage model based on the maximum displacement and cumulative energy consumption was proposed, which can consider the adverse effect of RAC on the seismic damage of columns. On this basis, the performance levels of composite columns are divided into five categories, The interlayer displacement angle and damage index are used as the damage quantitative indicators of composite columns, and the displacement angle limits of composite columns at different performance levels under 80% assurance rate are calculated as 1/105, 1/85, 1/65, 1/28, and 1/25 respectively. On this basis, the damage index limits corresponding to each performance level are calculated as 0.045, 0.1, 0.48, 0.8, and 1.0 respectively. Finally, the corresponding relations among the performance levels, damage degrees, interlayer displacement angles and damage indexes of composite columns are established. The conclusions can provide reference for the seismic design of SRRC filled circular steel tube composite columns, it fills the vacancy in the research on seismic damage of steel reinforced recycled concrete (SRRC) filled circular steel tube composite columns.

• Korean Chemical Engineering Research
• /
• v.62 no.1
• /
• pp.27-35
• /
• 2024

Fuel gases such as methane and propane are used in explosion hazardous area of domestic plants and can form non-uniform mixtures with the influence of process conditions due to leakage. The fire-explosion risk assessment using literature data measured under uniform mixtures, damage prediction can be obtained the different results from actual explosion accidents by gas leaks. An explosion characteristics such as explosion pressure and flame velocity of non-uniform gas mixtures with concentration change similar to that of facility leak were examined. The experiments were conducted in a closed 0.82 m long stainless steel duct with observation recorded by color high speed camera and piezo pressure sensor. Also we proposed the quantification method of non-uniform mixtures from a regression analysis model on the change of concentration difference with time in explosion duct. For the non-uniform condition of this study, the area of flame surface enlarged with increasing the concentration non-uniform in the flame propagation of methane and was similar to the wrinkled flame structure existing in a turbulent flame. The time to peak pressure of methane decreased as the non-uniform increased and the explosion pressure increased with increasing the non-uniform. The ranges of K_G (Deflagration index) of methane with the concentration non-uniform were 1.30 to 1.58 [MPa·m/s] and the increase rate of K_G was 17.7% in methane with changing from uniform to non-uniform.

• Korean journal of applied entomology
• /
• v.47 no.3
• /
• pp.217-226
• /
• 2008

Development of T. urticae was studied on the leaves of eggplant grown in hydroponics with potash contents of 0 mM, 2 mM, 6 mM, and 12 mM. As the levels of potash increased, that of nitrogen decreased and that of P, K, Mg increased in the plant. While contents of crude protein and fiber decreased, those of ash and sugar increased. Carbohydrate content was the highest at 2 mM. Water contents increased as those of potash increased with the exception at 0 mM. Biomass was the heaviest as 552.7 g at 6 mM and the lightest at 0 mM. Leaf thickness and the content of chlorophyll increased as the content of potash increased. Laboratory leaf disc tests provided with various potash levels revealed that feeding and oviposition preferences of T. urticae were high at 6 mM and 12 mM, respectively. Ratio of damaged leaf by naturally occurring T. urticae on eggplants of 99 days post-transplant in the greenhouse was the highest at 6 mM. Development of immature stages of T. urticae shortened as the levels of potash increased with a less tendancy in male than in female. No differences were detected in adult longevity and oviposition period but the number of eggs laid was the most as 84.7 at 6 mM and the least as 40.6 at 0 mM. There were no differences in the rate of egg hatch and the ratio of sex. $R_o,\;r_m,\;and\;{\lambda}$ were the highest at 6 mM and the lowest at 0 mM. T and Dt were the lowest at 6 mM and the highest at 0 mM. There was a descending trand of T. urticae developmet when levels of potash either gets high or low in the hydroponics.

• Research in Plant Disease
• /
• v.16 no.3
• /
• pp.238-246
• /
• 2010

In 2006 fall, a preliminary survey of viruses in two important medicinal plants, Cynanchum wilfordii and C. auriculatum, was conducted on the experimental fields at the Agricultural Research and Extension Services of Chungbuk province in Korea. On each experimental fields, percentage of virus infection was ranged from 20 to 80%, and especially an average of disease incidence propagated by roots was twice higher than that by seeds. The various symptoms were observed in Cynanchum spp. plants, such as mosaic, mottle, necrosis, yellowing, chlorotic spot and malformation etc. In electron microscopic examination of crude sap extracts, filamentous rod particles with 390-730 nm were observed in most samples. The virus particles were purified from the leaves of C. wilfordii with typical mosaic symptom, and the viral RNA was extracted from this sample containing 430-845 nm long filamentous rod. To identify the viruses, reverse transcription followed by PCR with random primers was carried out. The putative sequences of P3 and coat protein of potyvirus were obtained. From a BLAST of the two sequences, they showed 26-38% and 62-72% identities to potyviruses, respectively. In SDS-PAGE analysis, the subunit of coat protein was approximately 30.3 kDa, close to the coat protein of potyvirus. In bioassay with 21 species in 7 families, Chenopodium quinoa showed local lesion on inoculated leave and chlorotic spot on upper leave, but the others were not infected. RT-PCR detection using specific primer of C. wilfordii and C. auriculatum samples, all of 24 samples with virus symptom was positive, and five out of seven samples without virus symptom were also positive. On the basis of these data, the virus could be considered as a new member of potyvirus. We suggested that the name of the virus was Keunjorong mosaic virus (KjMV) after the common Korean name of C. wilfordii.

• The Korean Journal of Mycology
• /
• v.26 no.2 s.85
• /
• pp.265-274
• /
• 1998

This study was carried out to obtain the basic data for an artificial cultivation of Phellinus sp.. The optimum conditions for the mycelial growth on the different sawdusts (Quercus aliena, Morns alba and Alnus japonica) substrate of an isolated Phellinus sp. were optimized by response surface methodology. The ratio of rice bran addition to sawdust and the suitable moisture content for the mycelial growth in the all sawdust media were about 30% (w/w) and $65{\sim}70%$ (w/v), respectively. The initial pHs for the mycelial growth of Quercus aliena and Morns alba were in the range of $pH\;5{\sim}6$, whereas Alnus japonica was obtained at pH 6. The optimum temperature for the mycelial growth was about $25{\sim}30^{\circ}C$, depending on the different kinds of wood substrates. From the response surface analysis, the values of independent variables of Quercus aliena at stationary points were determined to be 31.01 % (w/w) of rice bran, pH of 5.31 and 69.03% (w/v) of moisture content, and the expected value of mycelial growth was about 8.32 cm. Both the ratio of rice bran addition to sawdust $(X_1)$ and moisture content $(X_3)$ were effective to the mycelial growth. In the case of Morns alba, the ratio of rice bran addition to sawdust, initial pH and moisture content at the stationary points were 28.77% (w/w), 5.28 and 69.8 (w/v),respectively, and the expected mycelial growth of 7.60 cm was obtained. Stationary points for the mycelial growth in the sawdust media of Alnus japonica were 28.74% (w/w) of rice bran, pH of 6. 04 and 66.96% (w/v) of moisture content, and the expected values of mycelial growth was about 5.38 cm. Based on the above results, there was correlations between the mycelial growth and independent variables, and the effect of rice bran $(X_1)$ and initial pH $(X_2)$ for the mycelial growth were higher than the moisture content $(X_3)$. The optimum species of sawdust media for the my celial growth of Phellinus sp. was in the order of Quercus aliena > Morns alba > Alnus japonica.

• Journal of Bio-Environment Control
• /
• v.26 no.3
• /
• pp.188-193
• /
• 2017

The purpose of this study was to investigate the changes of environmental conditions and the quality and yield of melon fruit by heat fan operation in greenhouses at winter season. The average daily temperature inside the tunnels during January 1 to 31, 2017 was $0.9^{\circ}C$ higher than that of the control $17.8^{\circ}C$. The air flow rate of heater fan treatment was 4.8 times higher than the control (untreated $0.05m{\cdot}s^{-1}$) at 20cm above the ground where the korean melon grew. The temperature of the heater pan was $5.6^{\circ}C$ higher than that of the untreated at $35.3^{\circ}C$ and the relative humidity was 8.1% lower than that of the untreated at 39.1%. The flowering rate of the heater fan treatment was 96%, 5% higher than the control. The number of first harvest days of heater fan treatment was shortened by 4 days than that of untreated treatment. Fruit quality and marketable fruit yield increased by 3.4% and 38% compared to untreated respectively, the heater fan treatment increased the temperature inside the greenhouse and air flow rete, which were beneficial for growing the korean melon in greenhouses at winter season.