• 한국전기전자재료학회논문지
• /
• 제16권5호
• /
• pp.361-364
• /
• 2003

It was investigated that the structural and electrical Properties of Ce-doped Ba(Zr$_{x}$Ti$_{1-x}$ )O$_3$ (BCZT) thin films with a mole fraction of x=0.2 and a thickness about 100 nm. BCZT films were prepared on Pt/Ti/SiO$_2$/Si substrate by a RF magnetron sputtering system. We have measured the thickness profile with Ar/O$_2$ ratio and the surface roughness. It was observed that the oxygen gas, which introduced during the film deposition, have an influence on the roughness of the film and the film roughness was reduced by annealing from 2.33 nm to 2.02 nm (RMS at 500 $^{\circ}C$, Ar:6 sccm, $O_2$:6 sccm). It was found that annealing procedure after top electrode deposit can reduce the dissipation factor.

• 한국재료학회지
• /
• 제9권12호
• /
• pp.1263-1269
• /
• 1999

본 실험에서는 반사층(reflector)을 이용한 FBAR (Film Bulk Acoustic Resonator) 즉, SMR (Solidly Mounted Resonator) 제조에 필요한 재료들의 최적 증착 조건을 설정하여, 이를 바탕으로 제조한 SMR의 특성을 보여주었다. SMR은 상하부 전극층, 압전 박막층, 반사층, 기판으로 구성된다. 상하부 전극으로 알루미늄(Al) 금속 박막을 사용하였고 압전 박막층으로 산화아연(ZnO) 박막을 사용하였다. 실리콘(Si) 기판과 하부 전극 사이에 위치하는 반사층은 5층의 이산화규소 ($Si_2$)와 텅스텐(W) 박막으로 구성되었다. 상하부 전극은 dc 스퍼터링 방법으로 증착아였으며 반사층과 압전 박막층은 rf 스퍼터링 방법으로 증착하였다. 최적 증착 조건에서 증착된 산화아연 (ZnO) 박막은 rocking curve에서 표준편차가 $2.17^{\circ}$의 우수한 c축 우선배향성, 비저항은 $10^4\;{\Omega}cm$이상, 막 표면 거칠기(rms roughness)는 10.6${\AA}$의 특성을 나타내었다. 최적 증착 조건에서 증착된 텅스텐(W)과 이산화규소($Si_2$) 박막의 특성은 박막 거칠기 (rms roughness)가 각각 16 ${\AA}$, 33 ${\AA}$을 나타내었다. 또한 증착된 알루미늄 금속 박막의 비저항은 $5.1{\times}10^{-6}\;{\Omega}cm$이었다. 반도체 기본 공정을 이용하여 면적 $250{\times}250\;{\mu}m^2$의 SMR 소자를 만들고, 네트웍 분석기로 SMR 소자의 공진 특성을 분석하였다. 공진특성은 1.244 GHz에서 직렬공진, 1.251 GHz에서 병렬공진을 나타내었다. SMR 소자의 공진특성에서 공진기의 Q값은 1200이었다.

• 한국광학회지
• /
• 제18권6호
• /
• pp.452-460
• /
• 2007

ZERODUR와 용융 석영으로 저산란 반사경을 제작하고 산란 특성을 연구하였다. Bowl feed 법을 이용하여 초연마면인 표면거칠기 0.326 ${\AA}$인 용융 석영 기판과 표면거칠기 0.292 ${\AA}$의 ZERODUR 기판을 얻었다. 이온빔 스퍼터링 방법으로 초연마된 기판 위에 $SiO_2$와 $Ta_2O_5$를 교번으로 22층을 증착하여 다층박막 고반사 거울을 얻었다. 용융 석영 반사경과 ZERODUR 반사경의 산란이 각각 4.6 ppm과 30.9 ppm으로 측정되었으며, 이로부터 산란이 매우 작은 경우 기판의 표면거칠기가 산란을 결정하는 주요 파라미터가 아니라는 것을 알았다. 나아가 반사경의 표면거칠기를 AFM으로 측정한 결과. ZERODUR 반사경이 용융 석영 반사경 보다 박막의 표면거칠기가 2.3배 더 높게 측정 되었다. 이 결과는 기판-박막 경계면에서 박막 형성 초기에 기판의 화학조성 또는 결정방향과 증착물질의 상호관계로 인하여 박막 형성 초기에 표면거칠기가 급격히 나빠져서 발생하는 것으로 유추되었다. SEO 300A으로 접촉각 측정을 하여 Giriflaco-Good-Fowkees-Young 방법으로 표면에너지를 계산하였다. 표면거칠기 0.46 ${\AA}$을 갖는 용융 석영 기판이 표면거칠기 0.31 ${\AA}$을 갖는 ZERODUR 기판보다 접촉각이 더 작고 표면에너지는 크게 나타났다. 이러한 차이가 기판 종류에 따라 박막형성 초기에 표면거칠기를 다르게 하는 한 요인으로 판단되며, 기판의 표면에너지가 높을수록 미려한 박막표면을 얻는 것으로 확인되었다. ZERODUR의 표면에너지 차이를 설명하기 위해 XPS 분석으로 용융 석영은 Si, O로 구성되었고 ZERODUR는 Si, O, Al, Na 그리고 F로 구성되었다는 것을 알 수 있었다.

• Tribology and Lubricants
• /
• 제36권4호
• /
• pp.232-243
• /
• 2020

It is essential to predict the amount of wear and surface parameters for a surface where relative motion occurs. In the asperity-based model for wear prediction, only the average contact pressure can be obtained. Hence, the accuracy of wear analysis is poor. In this study, DC-FFT is used to obtain the pressure of each node, and wear analysis is performed by considering the effect of the pressure gradient. The numerical surface generation method is used to create Gaussian, negatively skewed, and positively skewed surfaces for wear analysis. The spatial and height distributions of each surface are analyzed to confirm the effectiveness of the generated surface. Furthermore, wear analysis is performed using DC-FFT and Archard's wear formula. After analysis, it is confirmed that all peaks are removed and only valleys remain on the surface. The RMS roughness and Sk continue to decrease and Ku increases as the cycle progresses. It is observed that the surface parameters are significantly affected by the radius of curvature of the asperity. This analysis method is more accurate than the existing average wear and truncation models because the change in asperity shape during the wear process is reflected in detail.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.245-245
• /
• 2008

In this work, we describe the characterization of PVP films synthesized by spin-coater method and fabricate OTFTs of a bottom gate structure using pentacene as the active layer and polyvinylphenol (PVP) as the gate dielectric on Au gate electrode. We investigated the surface and electrical properties of PVP layer using an AFM method and MIM structure, and estimated the device properties of OTFTs including $I_D-V_D$, $I_D-V_G$, threshold voltage $V_T$, on/off ratio, and field effect mobility.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 1998년도 Proceedings of International Symposium on Remote Sensing
• /
• pp.180-185
• /
• 1998

Microwave polarimetric backscattering from a various types of grassland canopies has been analyzed by using the first-order radiative transfer theory in this paper. Leaves in the grassland are modeled by rectangular resistive sheets, which sizes (widths and lengths) and orientations (elevation and azimuth angles) are randomly distributed. Surface roughness and soil moisture of the ground plane under the grass canopy is considered in this computation. The backscattering coefficients of grasslands are computed for different radar parameters (angles, frequencies and Polarizations) as well as different canopy Parameters (size and orientation distributions of leaves, canopy depth, moisture contents of leaves and soil, rms height and correlation length of soil surface). A radar system for 15GHz has been fabricated and used for measurement of the scattering coefficient from a grass canopy. The computation result obtained by the scattering model for the grass canopy is compared with the measurements.

• 한국생산제조학회지
• /
• 제20권3호
• /
• pp.304-309
• /
• 2011

A monitoring system for magnetic abrasive polishing process is necessary to ensure the polishing products the high quality and integrity. Acoustic emission (AE) signal is known to reflect the material removal phenomena in other machining processes. In a case of the magnetic abrasive polishing of non-magnetic materials, application of AE method is very difficult because of lower machining force on the surface of workpiece and the level of AE signal is extremely lower. In this study, AE sensor-based monitoring system is applied to the magnetic abrasive polishing. The relation between the level of the AE RMS and the surface roughness during the magnetic abrasive polishing of magnesium alloy steel is investigated.

• 한국세라믹학회지
• /
• 제44권6호
• /
• pp.313-318
• /
• 2007

ITO (Indium-tin oxide) thin films have been prepared by a sol-gel spinning coating method and fired and annealed in the temperature range of $450-600^{\circ}C$. The XRD patterns of the films indicated the main peak of (222) plane and showed higher crystallinity with increasing an annealing temperature. The surface of the ITO thin films were treated with 0.1 N HCl 20% solution at room temperature. The effects of surface treatment on electrical properties and surface morphologies of the ITO films were investigated with the results of sheet resistance and FE-SEM, AFM images. The samples, subsequently treated with acidic solution for 40 sec showed the sheet resistance of $0.982\;k{\Omega}/square$. The surface treatment using acidic solution diminished the RMS (root mean square) value and the residual carbon content of the ITO films. It seemed that the acid-cleaning of the ITO thin films lead to the decrease of surface roughness and sheet resistance.

• 천문학논총
• /
• 제30권2호
• /
• pp.687-690
• /
• 2015

For research and development of Silicon Carbide (SiC) mirrors, the Korea Astronomy and Space Science Institute (KASI) and National Optical Astronomy Observatory (NOAO) have agreed to cooperate and share on polishing and measuring facilities, experience and human resources for two years (2014-2015). The main goals of the SiC mirror polishing are to achieve optical surface figures of less than 20 nm rms and optical surface roughness of less than 2 nm rms. In addition, Green Optics Co., Ltd (GO) has been interested in the SiC polishing and joined the partnership with KASI. KASI will be involved in the development of the SiC polishing and the optical surface measurement using three different kinds of SiC materials and manufacturing processes (POCO$^{TM}$, CoorsTek$^{TM}$ and SSG$^{TM}$ corporations) provided by NOAO. GO will polish the SiC substrate within requirements. Additionally, the requirements of the optical surface imperfections are given as: less than 40 um scratch and 500 um dig. In this paper, we introduce the international collaboration and interim results for SiC mirror polishing and development.

• 한국세라믹학회지
• /
• 제48권4호
• /
• pp.312-315
• /
• 2011

The effect of slurry composition and wafer flatness on a material removal rate (MRR) and resulting surface roughness which are evaluation parameters to determine the CMP characteristics of the on-axis 6H-SiC substrate were systematically investigated. 2-inch SiC wafers were fabricated from the ingot grown by a conventional physical vapor transport (PVT) method were used for this study. The SiC substrate after the CMP process using slurry added oxidizers into slurry consisted of KOH-based colloidal silica and nano-size diamond particle exhibited the significant MRR value and a fine surface without any surface damages. SiC wafers with high bow value after the CMP process exhibited large variation in surface roughness value compared to wafer with low bow value. The CMPprocessed SiC wafer having a low bow value of 1im was observed to result in the Root-mean-square height (RMS) value of 2.747 A and the mean height (Ra) value of 2.147 A.