• Journal of the Korean Ceramic Society
• /
• v.32 no.12
• /
• pp.1417-1423
• /
• 1995

α/β sialon based composites containing silicon nitride whisker and silicon carbide platelet were fabricated by hot pressing. Effect of the reinforcing agents on the α to β phase transformation of the sialon as well as on the mechanical properties was investigated. Silicon nitride whisker and silicon carbide platelet promoted the phse transformation. TEM/EDS analysis revealed that the grain containing the whisker had 'core-rim' structure; core being high purity Si3N4 whisker and rim being β-sialon. Flexural strength of the composite decreased with the reinforcement addition which, on the other hand, improved fracture toughness of it. High temperature strength was measured at 1300℃ to be about 130 MPa lower than that measured at RT for the whisker reinforced composites.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.644-645
• /
• 2006

TiC-and Ti(C,N)-based cermets are excellent in semi-and final finishing of work piece during cutting operations. Typical microstructure of the cermets is a core/rim structure. The undissolved Ti(C,N) cores contribute to their high hardness while the rim phases, (Ti,M1,M2)(C,N)-type solid solutions, play great roles in enhancing the toughness. In this paper, various ultrafine pre-mixed MeC-Ni powders were synthesized and the powders were sintered or hot pressed after mixing in order to control the size and volume fractions of core and rim phases in the system. This paper will present the factors determining the microstructure along with mechanical properties.

• Bulletin of the Korean Chemical Society
• /
• v.17 no.6
• /
• pp.502-506
• /
• 1996

Several ester group-containing calix[4]arenes were synthesized by the reaction of calix[4]arene and various acyl chlorides. Two or four ethyl succinyl units could be introduced into the calix[4]arene lower rim depending on the reaction conditions. But the mixture of three and four ethyl malonyl substituted calix[4]arenes were obtained and only three ethyl oxalyl units were introduced at the lower rim of calix[4]arene. Interestingly when calix[4]arene was treated with ethyl oxalyl chloride in the presence of aluminum chloride, two ethyl oxalyl units were introduced at the upper rim of calix[4]arene. The conformation of those ester-containing calix[4]arenes was presented based on the 1H and 13C NMR spectra.

• Korean Journal of Audiology
• /
• v.23 no.4
• /
• pp.210-213
• /
• 2019

The auricle is a three-dimensional cartilaginous frame covered with thin overlying skin. Due to its complex features, reconstructing helical rim defects after the excision of an auricular mass is challenging. Shortage of subcutaneous tissue and the presence of a tightly bound epithelium further hamper the primary closure of lateral (anterior) auricular skin defects. We present herein a case in which we used a helical rim advancement flap along with an additional postauricular skin flap. We achieved a satisfactory esthetic result with minimal loss of helical diameter and a low risk of flap necrosis by preserving the vascular network of the flap. This technique is less traumatic and will facilitate faster healing as well as improved patient recovery.

• Journal of Audiology & Otology
• /
• v.23 no.4
• /
• pp.210-213
• /
• 2019

The auricle is a three-dimensional cartilaginous frame covered with thin overlying skin. Due to its complex features, reconstructing helical rim defects after the excision of an auricular mass is challenging. Shortage of subcutaneous tissue and the presence of a tightly bound epithelium further hamper the primary closure of lateral (anterior) auricular skin defects. We present herein a case in which we used a helical rim advancement flap along with an additional postauricular skin flap. We achieved a satisfactory esthetic result with minimal loss of helical diameter and a low risk of flap necrosis by preserving the vascular network of the flap. This technique is less traumatic and will facilitate faster healing as well as improved patient recovery.

• Korea Trade Review
• /
• v.45 no.5
• /
• pp.75-89
• /
• 2020

The purpose of this paper was to analyze the trend of container volume using the Seasonal Autoregressive Intergrated Moving Average (SARIMA) model. To this end, this paper used monthly time-series data of the East Sea Rim from 2001 to 2019. As a result, the SARIMA(2,1,1)12 model was identified as the most suitable model, and the superiority of the SARIMA model was demonstrated by comparative analysis with the ARIMA model. In addition, to confirmed forecasting accuracy of SARIMA model, this paper compares the volume of predict container to the actual volume. According to the forecast for 24 months from 2020 to 2021, the volume of containaer increased from 60,100,000Ton in 2020 to 64,900,000Ton in 2021

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.04a
• /
• pp.183-186
• /
• 2003

Reaction injection molding (RIM) is a widely used process for producing various kinds of complex parts including automobiles, furniture, appliances, and housings. In RIM, products are made from two or more chemical components through mixing, chemical reaction, and molding [1]. Liquid reactants from two supply tanks flow at high pressure into a mix head, where they impinge at high velocity. (omitted)

• Proceedings of the Korean Ceranic Society Conference
• /
• 2000.04a
• /
• pp.117.2-117.2
• /
• 2000

• Journal of applied mathematics & informatics
• /
• v.30 no.5_6
• /
• pp.993-1003
• /
• 2012

The family of graphs $\hat{W}_{4n}$ is defined by taking the simple whee graph $W_{n+1}$ with $n$ rim vertices and then adding three extra vertices on every rim edge of the wheel. In this paper, the critical group of this whole family of graphs is investigated.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.10 no.2
• /
• pp.45-53
• /
• 1985

In the present paper, the capacitated solid transportation problem (planar constraints) is considered with upper and lower bounds on the rim conditions. The considered model has been shown to be equipvalent to a standard capacitated 3-index transportation problem. A procedure to solve any capacitated 3-index transportion problem is also suggested. Some special cases of the considered model have been shown to conform to possible practical situations.