• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.6
• /
• pp.493-498
• /
• 2005

Al doped Zinc Oxide, which is widely used as a transparent conductor in opto-electronic devices. In this paper, we find that the lateral variations of the parameters of the ZnO:Al films prepared by the rf magnetron sputtering can be reduced to acceptable levels by optimising the deposition parameters. The effect of bias voltage on the electrical, optical and morphological properties were investigated experimentally. we investigated sample properties of Bias Voltage change in 0 to 50 V.

• Korean Journal of Materials Research
• /
• v.8 no.10
• /
• pp.961-968
• /
• 1998

In order to investigate the effects of substrate bias voltage on the formation of$ZnS-SiO_2$ protective film in phase change optical disk by R.F. magnetron sputtering method, thin dielectric film was formed on Si wafer and Corning glass by using ZnS(80mol%)-$SiO_2$(20mol%)t arget under argon gas. In this study, the Taguchi experimental method was applied in order to obtain optimum conditions with reduced number of experiments and to control numerous variables effectively. At the same time this method can assure the reproducibility of experiments. Optimum conditions for film formation obtained by above method were target RF power of 200 W. substrate RF power of 20 W, Ar pressure of 5 mTorr. sputtering time of 20 min.. respectively. The phase of specimen was determined by using XRD and TEM. The compositional analysis of specimen was performed by XPS test. In order to measure the thermal resistivity of deposited specimen, annealing test was carried out at $300^{\circ}C$ and $600^{\circ}C$. For the account of void fraction in thin film, the Bruggeman EMA(Effective Medium Approximation) method was applied using the optical data obtained by Spectroscopic Ellipsometry. According to the results of this work, the existence of strong interaction between bias voltage and sputtering time was confirmed for refractive index value. According to XRD and TEM analysis of specimen, the film structure formed in bias voltage resulted in more refined structures than that formed without bias voltage. But excess bias voltage resulted in grain growth in thin film. It was confirmed that the application of optimum bias voltage increased film density by reduction of void fraction of about 3.7%.

• Journal of the Korean Vacuum Society
• /
• v.13 no.4
• /
• pp.150-156
• /
• 2004

Boron nitride thin films were deposited on Si(100) substrate by RF (Radio-frequency) UBM (Unbalanced Magnetron) sputtering system. The effect of working pressure and substrate bias voltage on microstructure and compressive stress of boron nitride thin films has been investigated. In high working pressure, the alignment of hBN laminates increased with substrate bias voltage, in low working pressure, however, it was high in low substrate bias voltage. Compressive stress evolution and surface morphology of deposited BN films are closely related with the alignment of hBN laminates. The cBN phase without high compressive stress could be nucleated on hBN thin film by controlling the alignment of hBN laminates.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.123-123
• /
• 2008

In this work, amorphous carbon thin films were deposited for hard mask applications by a reactive particle beam (RPB) assisted sputtering system at room temperature. The depositing characteristics of the films were investigated as functions of operating parameters such as reflector bias voltage and RF plasma power. It was confirmed that the deposition rate increased with increasing the reflector bias voltage and RF plasma power. By an atomic force microscope (AFM), it was revealed that the surface roughness was also increased. The total stress in films was determined by the use of the substrate curvature and its result will be discussed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.331-331
• /
• 2008

Transparent conductive oxide (TCO) are necessary as front electrode or anti-reflecting coating for increasing efficiency of LED and Photodiode. In this paper, aluminum-doped Zinc oxide films(AZO) were prepared by RF magnetron sputtering on Si substrate at room temperature with application of substrate bias from -60 to 60 V. Then annealed at temperature of 200, 300 and $400^{\circ}C$ for 1hr in $H_2$ ambient. Structural and electrical property of AZO thin films were investigated.

• Korean Journal of Materials Research
• /
• v.33 no.9
• /
• pp.372-376
• /
• 2023

Transparent conductive tungsten (W) doped indium oxide (In₂O₃; IWO) films were deposited at different substrate bias voltage (-V_b) conditions at room temperature on glass substrates by radio frequency (RF) magnetron sputtering and the influence of the substrate bias voltage on the optical and electrical properties was investigated. As the substrate bias voltage increased to -350 V_b, the IWO films showed a lower resistivity of 2.06 × 10^-4 Ωcm. The lowest resistivity observed for the film deposited at -350 V_b could be attributed to its higher mobility, of 31.8 cm²/Vs compared with that (6.2 cm²/Vs) of the films deposited without a substrate bias voltage (0 V_b). The highest visible transmittance of 84.1 % was also observed for the films deposited at the -350 V_b condition. The X-ray diffraction observation indicated the IWO films deposited without substrate bias voltage were amorphous phase without any diffraction peaks, while the films deposited with bias voltage were polycrystalline with a low In₂O₃ (222) diffraction peak and relatively high intensity (431) and (046) diffraction peaks. From the observed visible transmittance and electrical properties, it is concluded that the opto-electrical performance of the polycrystalline IWO film deposited by RF magnetron sputtering can be enhanced with effective substrate bias voltage conditions.

• Corrosion Science and Technology
• /
• v.3 no.4
• /
• pp.148-153
• /
• 2004

Magnesium thin flims were prepared on cold-rolled steel substrates by RF magnetron sputtering technique. The influence of argon gas pressure and substrate bias voltage on their crystal orientation and morphology of the coated films were investigated by scanning electron microscopy (SEM) and X-ray diffraction, respectively. And the effect of crystal orientation and morphology of magnesium films on corrosion behaviors was estimated by measuring anodic polarization curves in deaerated 3%NaCl solution. From the experimental results, all the sputtered magnesium films showed obviously good corrosion resistance to compare with 99.99% magnesium target of the sputter-evaporation metal. Finally it was shown that the Corrosion-resistance of magnesium films can be improved greatly by controlling the crystal orientation and morphology with effective use of the plasma sputtering technique.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.103-104
• /
• 2008

In this paper we report upon an investigation into the effect of DC bias voltage on the electrical and optical properties of Gallium doped zinc oxide (GZO) film. GZO films were deposited on glass substrate without substrate temperature by RF magnetron sputtering from a ZnO target mixed with 5 wt% $Ga_2O_3$. we investigated sample properties of bias voltage change in 0 to -60 V. We were able to achieve as low as $5.89\times10^{-4}$ ${\Omega}cm$ and transmittance over 87%. without substrate temperature.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.5
• /
• pp.373-376
• /
• 2009

In this paper we report upon an investigation into the effect of DC bias voltage on the electrical and optical properties of Gallium doped zinc oxide (GZO) film. GZO films were deposited on glass substrate without substrate temperature by RF magnetron sputtering from a ZnO target mixed with 5 wt% $Ga_{2}O_{3}$. we investigated sample properties of bias voltage change in 0 to -60 V. We were able to achieve as low as $5.89{\times}10^{-4}{\Omega}cm$ and transmittance over 88 %. without substrate heating.

• Analytical Science and Technology
• /
• v.7 no.2
• /
• pp.155-164
• /
• 1994

A conventional Grimm-type glow discharge source was constructed and applied to radio-frequency(13.56MHz) discharge for metal and ceramic analysis. We investigated the emission spectrum for aluminium and aluminium oxide and the influence of discharge operating paramaters including argon pressure, rf-power and DC-bias voltages at the sample-side electrode. Scanning Electron Microscope(SEM) also was used to investigate the effect of rf-sputtering on the microstructure formation of the aluminium oxide. Linear analytical calibration curves were constructed for Manganese and zinc element in samples of low alloy steel(BAS 401-405) and brass(NIST 1108-1117).