• Journal of Korea Society of Digital Industry and Information Management
• /
• v.14 no.4
• /
• pp.93-99
• /
• 2018

This paper presents an implementation method using NDK (Network Developer's Kit) of GNU (GNU is Not Unix) Radio and Multicore DSP (Digital Signal Processor) to implement LTE (Long Term Evolution) SDR (Software Defined Radio) Platform. In order to satisfy 1.4MHz, 3MHz, 5MHz and 10MHz of the bandwidth supported by LTE, USRP (Universal Software Radio Peripheral) X series which is an RF (Radio Frequency) transceiver of Ettus Research was used. To control this, GNU Radio which is an open source software radio toolkit was used. We also used NDK from TI (Texas Instruments) DSP to transfer data between USRP and DSP. Experimental results show throughput results according to each bandwidth, thus confirming the feasibility of implementing LTE SDR Platform using GNU Radio and NDK of TI DSP.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.5
• /
• pp.261-269
• /
• 2016

A high-performance transmit/receive (T/R) switch is essential for every radio-frequency (RF) device. This paper proposes a T/R switch that is designed in the CEDEC 0.13 μm complementary metal-oxide-semiconductor (CMOS) technology for 2.4 GHz ISM-band RF applications. The switch exhibits a 1 dB insertion loss, a 28.6 dB isolation, and a 35.8 dBm power-handling capacity in the transmit mode; meanwhile, for the 1.8 V/0 V control voltages, a 1.1 dB insertion loss and a 19.4 dB isolation were exhibited with an extremely-low power dissipation of 377.14 μW in the receive mode. Besides, the variations of the insertion loss and the isolation of the switch for a temperature change from - 25℃ to 125℃ are 0.019 dB and 0.095 dB, respectively. To obtain a lucrative performance, an active inductor-based resonant circuit, body floating, a transistor W/L optimization, and an isolated CMOS structure were adopted for the switch design. Further, due to the avoidance of bulky inductors and capacitors, a very small chip size of 0.0207 mm² that is the lowest-ever reported chip area for this frequency band was achieved.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.11 no.6
• /
• pp.47-54
• /
• 2008

In this paper, interference analysis has been performed between RF receiver and transmitters on each soldier for Multiple Integrated Laser Engagement System(MILES) which are following ZigBee standard. In order to obtain minimum transmit power without interference, 1% Packet Error Rates(PER) from 14 transmitters attached on a soldier to a receiver are measured with the scenarios for simple transmitting and receiving network configuration and for repeating network configuration. Based on this transmit power, the available distance for interference free among soldiers is simulated using Spectrum Engineering Advanced Monte Carlo Analysis Tool(SEAMCAT). Later scenario gives the benefit of 10dB lower transmit power, smaller and lighter power source, and better activity of trainee.

• Journal of KIISE:Information Networking
• /
• v.37 no.3
• /
• pp.217-227
• /
• 2010

To apply active RFID technology in the various kinds of industry, it needs to quickly transmit a large amount of data. ISO/IEC 18000-7 standard uses the 433.92MHz as single channel system and its transmit rate is just 27.8kbps, that is insufficient for a large amount of data transmission. To solve this problem, we designed a new data transmission protocol using 2.4GHz band. The feature of designed protocol is not only making over 255bytes data messages using the Burst Read UDB but also efficiently transmitting it. To implement this protocol, we use Texas Instruments's SmartRF04 develop kit and CC2500 transceiver as RF module. As an evaluation of 63.75kbytes data transmission, we demonstrate that transmission time of Burst Read UDB has improved as 17.95% faster than that of Read UDB in the ISO/IEC 18000-7.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.5
• /
• pp.558-565
• /
• 2013

In this paper, modeling and simulation for performance analysis of high resolution SAR system has been carried out in the time, frequency and numeric domain using ADS Ptolemy simulation tool of Agilent corporation. SAR system consists of antenna, controller and transceiver. Error parameters affecting SAR system performances have been defined, modeled and simulated such as phase noise of frequency synthesizer, amplitude and phase characteristic of TWTA, sampling frequency of waveform generator and I/Q imbalance. Finally, the development requirements of SAR system based on the impulse response function have been derived.

• Journal of Satellite, Information and Communications
• /
• v.7 no.1
• /
• pp.75-81
• /
• 2012

This study is to design the transmitter and receiver of short range UWB(Ultra Wide Band) imaging radar that is able to display high resolution radar image for front area of a UGV(Unmanned Ground Vehicle). This radar can help a UGV to navigate autonomously as it detects and avoids obstacles through foliage. The transmitter needs two transmitters to improve the azimuth resolution. Multi-channel receivers are required to synthesize radar image. Transmitter consists of high power amplifier, channel selection switch, and waveform generator. Receiver is composed of sixteen channel receivers, receiver channel converter, and frequency down converter, Before manufacturing it, the proposed architecture of transceiver is proved by modeling and simulation using several parameters. Then, it was manufactured by using industrial RF(Radio Frequency) components and all other measured parameters in the specification were satisfied as well.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.11
• /
• pp.2021-2026
• /
• 2007

In the parer, we design a non-coherent UWB system by adopting the architecture of a simplified asynchronous transmission and the edge-triggered pulse transmission, which makes e system performance independent of the share of the transmitted waveform, robust to multipath channels. The designed non-coherent UWB transceiver architecture has an advantage of the simple realization since any mixer, high-speed correlator, and high-sampling A/D converter are not necessary at the cost of performance degradation of about 3dB. Further, the designed non-coherent UWB transceiver is actually implemented with the wireless CANVAS prototype testbed in short range indoor application environments such as a lecture room. The implemented prototype testbed is proven to offer the data rate of 115kbps on the conditions of Peer-to-Peer(P-to-P) in the indoor channel within the range of about 10m.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.5
• /
• pp.445-453
• /
• 2016

This paper presents the implementation and design of the 1T-1R wireless HD video streaming systems over 28 GHz mmWave frequency using 3GPP LTE-TDD standard on NI USRP RIO SDR platform. The baseband of the system uses USRP RIO that are stored in Xilinx Kintex-7 chip to implement LTE-TDD transceiver modem, the signal that are transceived from USRP RIO up or down converts to 28 GHz by using self-designed 28 GHz RF transceiver modules and it is finally communicated HD video data through self-designed $4{\times}8$ sub array antennas. It is that communication method between USRP RIO and Host PC use PCI express ${\times}4$ to minimize delay of data to transmit and receive. The implemented system show high error vector magnitude performance above 25.85 dBc and to transceive HD video in experiment environment anywhere.

• The Journal of the Korea Contents Association
• /
• v.9 no.4
• /
• pp.19-26
• /
• 2009

The microwave exposure device for microwave breast cancer detection consists of RF transceiver and several antennas. The microwave information of object acquired from the microwave exposure device can be calculated permittivity and conductivity by using the inverse scattered analysis. In this paper, we have developed the software for detecting breast cancers based on microwave tomography, by which users not only can check out the existence of breast cancers through the permittivity and conductivity information analysis of the object's internal, but also can analysis easily information for distribution of breast cancers. The developed software provides the function for visualizing the captured permittivity and conductivity information as 2D or 3D color images on which users can easily detect the existence of breast cancers. For more detailed analysis of tomography images, the proposed software also has provided the functions for displaying their cutting profiles as well as position and size information of special area in them.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.5 s.347
• /
• pp.77-83
• /
• 2006

In this paper, we designed, constructed and evaluated the system for the FTTH suited to a residence and apartment using CWDM-PON techniques. These systems have capacity to service at 100Mbps rate to 384 users in the same breath. Also, the services include the internet, CATV, IPTV and wireless LAN. In the case of ire network, the data could be transmitted by UTP cable and optical fiber and case of wireless one, the data transmitted using WLAN. The distance between the cental office and the user is 20km and the data rate is 100Mbps maximum. Of course, the optical network used just one fiber optical core. For the basic material, we obtained the characteristics of optical transceiver module, Mux/Demux and transmission qualities depends on the environment.