• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.1
• /
• pp.182-187
• /
• 2009

In this paper, the power management module of wireless sensor node is designed and fabricated utilizing RF energy from reader antenna of commercial RFID system, which is mainly categorized in the energy harvesting. For this, the rectenna and the high efficient boost converter is designed to get the DC power from RF power for the charging the battery. When the RF power from RFID reader antenna is 1.2[W], the DC power of 3.1[mW] at the distance of 1[m] and 1[mW] at 5.5[m] are obtained. Considering the connection to the battery, the boost converter for enhancing the conversion efficiency is designed. The conversion efficiency at the distance of 4[m] is 79.3[%] and the harvested power is 1.36[mW] which is actually used for the charging the battery. This value is available in the wireless sensor networking.

• Journal of Sensor Science and Technology
• /
• v.4 no.2
• /
• pp.58-63
• /
• 1995

The effects of substrate temperature, RF power, and $NH_{3}/SiH_{4}$ gas flow ratio on the dielectric constant and optical bandgap of amorphous silicon nitride (a-SiNx:H) thin films prepared by PECVD method using RF glow discharge decomposition of $SiH_{4}$ and $NH_{3}$ gas mixtures have been studied. The dielectric constant and optical bandgap of a-SiNx:H thin films were greatly exchanged as by increasing substrate temperature, RF power, and $NH_{3}/SiH_{4}$ gas flow ratio. The dielectric constant of a-SiNx:H films was increased and optical bandgap of a-SiNx:H films was decreased as the substrate temperature was increased. When the substrate temperature, RF power, gas pressure, $NH_{3}/SiH_{4}$ gas flow ratio, and thickness were $250^{\circ}C$, 20 W, 500 mTorr, 10 and $1500\;{\AA}$, respectively, the dielectric constant, breakdown field and optical bandgap of a-SiNx:H film were 4.3, 1 MV/cm, and 2.9 eV, respectively.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.4
• /
• pp.32-38
• /
• 2011

This paper describes implementation of the 5.0GHz RF frequency synthesizer with 0.18${\mu}m$ silicon CMOS technology being used as an application of the IEEE802.15.4 USN sensor node transceiver modules. To get good performance of speed and noise, design of the each module like VCO, prescaler, 1/N divider, fractional divider with ${\Sigma}-{\Delta}$ modulator, and common circuits of the PLL has been optimized. Especially to get excellent performance of high speed and wide tuning range, N-P MOS core structure and 12 step cap banks have been used in design of the VCO. The chip area including pads for testing is $1.1{\times}0.7mm^2$, and the chip area only core for IP in SoC is $1.0{\times}0.4mm^2$. Through analysing of the fabricated frequency synthesizer, we can see that it has wide operation range and excellent frequency characteristics.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.5
• /
• pp.49-54
• /
• 2009

This paper describes implementation of the 1.9GHz RF frequency synthesizer with $0.18{\mu}m$ silicon CMOS technology being used as an application of the USN sensor node transceiver modules. To get good performance of speed and noise, design of the each module like VCO, prescaler, 1/N divider, fractional divider with ${\Sigma }-{\Delta}$ modulator, and common circuits of the PLL has been optimized. Especially to get good performance of speed, power consumption, and wide tuning range, N-P MOS core structure has been used in design of the VCO. The chip area including pads for testing is $1.2{\times}0.7mm^2$, and the chip area only core for IP in SoC is $1.1{\times}0.4mm^2$. The test results show that there is no special spurs except -63.06dB of the 6MHz reference spurs in the PLL circuitry. There is good phase noise performance like -116.17dBc/Hz in 1MHz offset frequency.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.45 no.6
• /
• pp.87-93
• /
• 2008

This paper describes implementation of the 5.0GHz RF frequency synthesizer with $0.18{\mu}m$ silicon CMOS technology being used as an application of the IEEE802.15.4 USN sensor node transceiver modules. To get good performance of speed and noise, design of the each module like VCO, prescaler, 1/N divider, fractional divider with ${\Sigma}-{\Delta}$ modulator, and common circuits of the PLL has been optimized. Especially to get good performance of speed, power consumption, and wide tuning range, N-P MOS core structure has been used in design of the VCO. The chip area including pads for testing is $1.1*0.7mm^2$, and the chip area only core for IP in SoC is $1.0*0.4mm^2$. Through comparing and analysing of the designed two kind of the frequency synthesizer, we can conclude that if we improve a litter characteristics there is no problem to use their as IPs.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.9
• /
• pp.1941-1946
• /
• 2009

Wireless sensor networks do the monitoring and collecting information in the environment instead of human. Sensor networks are consisted of small sensor nodes with very limited hardware resource and very low network bandwidth. The wireless communication environment causes lots of communication errors so that the sensor network requires error correction technique to increase the reliability of network. The performance of error correction technique could be increased by the researches about the error pattern of CRC. In the paper, we did the performance evaluation - transmission interval, distance between sensor nodes, racket size, and RF power - that affects to the success ratio of data transmission in the indoor environment. we propose the performance metrics of system configuration based on the analysis of performance evaluation.

• Journal of Sensor Science and Technology
• /
• v.20 no.3
• /
• pp.145-150
• /
• 2011

In this paper, we designed a tunable microstrip patch antenna using RF MEMS switches. The design and simulation of the antenna were performed using a high frequency structure simulator(HFSS). The antenna was designed for use in the ISM band and either operates at 2.4 GHz or 5.7 GHz achieving -10 dB return-loss bandwidths of 20 MHz and 180 MHz, respectively. In order to obtain high efficiency and improve the ease of integration, a high resistivity silicon(HRS) wafer on a glass substrate was used for the antenna. The antenna achieved high gains: 8 dB at 5.7 GHz and 1 dB at 2.4 GHz. The RF MEMS DC contact switches were simulated and analyzed using ANSYS software.

• Journal of Sensor Science and Technology
• /
• v.15 no.1
• /
• pp.71-75
• /
• 2006

ITO (Indium Tin Oxide) thin films have been fabricated by rf magnetron sputtering with a target of a mixture $In_{2}O_{3]$(90 wt%) and $SnO_{2}$ (10 wt%). ITO films were sputtered with substrate temperature from 30 to $300^{\circ}C$ and working pressure from 1 to under 0.1 m Torr. ITO thin films surface morphology and electrical properties analyzed by SEM Photographs, and X-ray diffractions patterns. The resistivity of ITO thin films was $1.8{\times}10^{-5}{\Omega}/cm$.

• Journal of Sensor Science and Technology
• /
• v.20 no.2
• /
• pp.77-81
• /
• 2011

This paper presents a single-pole eight-throw(SP8T) switch based on proposed a radio-frequency(RF) microelectromechanical systems (MEMS) switches. The proposed switch was driven by a double stop(DS) comb drive, with a lateral resistive contact. Additionally, the proposed switch was designed to have tapered signal line and bi-directionally actuated. A forward actuation connects between signal lines and contact part, and the output becomes on-state. A reverse actuation connects between ground lines and contact part, and the output becomes off-state. The SP8T switch of 3-stage tree topology was developed based on an arrangement of the proposed RF MEMS switches. The developed SP8T switch had an actuation voltage of 12 V, an insertion loss of 1.3 dB, a return loss of 15.1 dB, and an isolation of 31.4 dB at 6 GHz.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2009.04a
• /
• pp.1065-1068
• /
• 2009

유비쿼터스(Ubiquitous) 시대의 도래와 함께 무선 센서 네트워크기반 연구가 다방면에서 활발히 진행되고 있다. 또한 센서 네트워크를 이용한 산업이 활발하다. 본 논문에서는 유비쿼터스 시대에 걸맞게 센서 네트워크 기술을 이용한 침입 탐지 시스템을 제안하고, 이를 구현하였다. 이에 MICAz모트를 이용하여 설계하였으며 조도, 가속도센서와 RF신호를 이용하였다.