• Proceedings of the Korean Information Science Society Conference
• /
• 2012.06d
• /
• pp.271-273
• /
• 2012

본 논문은 장거리 RF통신모듈을 적용하여 고정적인 통신비용이 없으며 5Km전후의 장거리 무선데이터 통신이 가능한 산업용 관제시스템을 구현함으로써 다양한 분야의 산업용 관제시스템에 대한 실증자료로 활용하고, 구현과정에서 발생한 문제점을 고찰하여, 최적의 방안을 도출하는데 목적이 있다. 이에 본 논문에서는 선박 건조 시 사용되는 조선소 화재감시시스템을 구현함으로써 산업용 관제시스템 구현에 있어 장거리 RF통신모듈의 적합성을 확인하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.2
• /
• pp.327-332
• /
• 2008

New RF matcher module has been proposed in this paper for improvement of RF matcher in plasma etcher system using in semiconductor and display panel manufacturing process. New designed warm gear was used instead of bevel gear in new driving module, and control system was re-arranged with one-chip micro-process technique. The matching performance of new match module was improved in various process condition with reduction of backlash and matching time, and flexible motion of motor compared commercial match module. However this new type RF match module will improve the productivity in etching process of the mass production line.

• Journal of IKEEE
• /
• v.3 no.2 s.5
• /
• pp.186-195
• /
• 1999

In this paper, the RF-modules composed of front-end, frequency synthesizer, modulator/demodulator and power control multi channel WLL personal system for W-CDMA using 10 [MHz] RF channel bandwidth has been implemented and considered. The measured transmission power is 250 [mW] which is very close to the required value. The measured flatness of power at the final output stage is ${\pm}1.5[dB]$ over the required bandwidth of the receiver. In addition, it is found that the chip rate transmitting spread signal is set to 8.192 [MHz], the required rate. The frequencies of RF_LO signal and LO signal of the modulator and the demodulator measured by a frequency synthesizer are satisfied with design requirements. The operating range of the receiving strength signal indicator and AGC units shows 60 [dB] respectively. Also the measured phasor diagram and eye pattern for deciding the RF modules compatible with baseband digital signal processing part are shown good results.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.5A
• /
• pp.519-527
• /
• 2010

In this paper, we design and implement a broadband LNA(Low Noise Amplifier), a mixer, and oscillators in RF module part for radar detector. For resolving the limitation of the conventional product that the sensitivity is low due to the poor gain flatness, we propose the architecture of RF module part. The proposed RF module part is composed with a broadband 2-stage LNA, a mixer, and three oscillators, and improves the maximum gain and gain flatness for detecting various frequencies. The overall performances of RF module part are above 38 dB conversion gain in whole band and 1 dB gain flatness. These results show that the maximum gain which is the problem of the conventional product is improved 6 dB from 35 dB to 41 dB, and gain flatness is also improved 17 dB from 22 dB to 5 dB.

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.3
• /
• pp.19-25
• /
• 2000

In this paper, we describe RF receiver module for IMT-2000 handset with 5 MHz channel bandwidth. The fabricated RF receiver module consists of Low Noise Amplifier, RF SAW filter, Down-converter, If SAW filter, AGC and PLL Synthesizer. The NF and IIP3 of LNA is 0.8 dB, 3 dBm at 2.14 GHz, conversion gain of down-converter is 10 dB, dynamic range of AGC is 80 dB, and phase noise of PLL is -100 dBc at 100 kHz. The receiver sensitivity is -110 dBm, adjacent channel selectivity is 48 dBm.

• Journal of the Korea Convergence Society
• /
• v.8 no.11
• /
• pp.85-91
• /
• 2017

This paper concerns the design of a matching module system enabling the RF signal to be harmonized between the new base stations (RRH) and the repeater in the same frequency band of the asynchronous transfer network. This matching system controls the RF Gain Control of the module while monitoring the quality of the quality. Additionally, the RF environment has been adapted accordingly to adjust the RF Gain Control to match the receiver characteristics of the relay. As a result of this study, we improved the quality of the interface between the new base stations and existing relays.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.6
• /
• pp.900-909
• /
• 1999

The receiving part of the RF system for the digital TRS base stations is developed in this paper. Based on the system specifications, the structure of the RF system is accomplished and its block diagram is drawn. The RF system is implemented according to these block diagrams. Subsequently the RF band-pass filter, the low noise amplifier, the automatic level controlled attenuator, the frequency synthesizer and other components for the system are designed and implemented, and a main board to integrate these modules is also manufactured. To lower the noise floor of the system and suppress the RF spurious noise, a PCB layout is performed carefully. For each module consisting of the RF system and the entire system, the performance tests are accomplished to check the specifications.

• Journal of Digital Convergence
• /
• v.12 no.12
• /
• pp.257-264
• /
• 2014

Through MCU model, Radio Frequency communication is completed using universal asynchronous receiver and transmitter. The communicatin with PC and MCU is completed using RS-232 cable. At first interconnected communication with PC and MCU is necessary for RF communication because tha UART is based technique for RF communication. Program imbeded in microcontroller unit is ran during RF signal is transmitted to other RF module. Data connected with PC and MCU is transmitted between PC and MCU during PC and MCU is connected.

• Journal of Korea Society of Industrial Information Systems
• /
• v.6 no.2
• /
• pp.31-37
• /
• 2001

In this paper, We designed and implemented an RF module for WLL multi-channel personal stations. Then, we experimentally evaluated in receiving sensitivity, adjacent channel interference selectivity and spurious response limit. From the measurement results on the RF module for WLL multi-channel personal stations, we observed and confirmed as follows: First, the variation in output power level was kept to be less than 30 dBm in the range of the input power level from -90 dBm to -30dBm. This measurement result confirmed the dynamic range of 60 dB. Secondly, at the output stage of the RF module, the gain flatness in the pass band was measured to be less than 2dB, which confirmed a precise control of the bandspread signals. Thirdly, at the RF module, the bandwidth and power level in transmission were measured to be 10 MHz, respectively we note that these features satisfy the design specifications.

• Journal of Advanced Navigation Technology
• /
• v.14 no.3
• /
• pp.391-396
• /
• 2010

This paper presents some important research result comparisons for multi function RF modules which use amplifier or frequency multiplier. By using multiplier, multi function module can be realized amply in comparison to multi band module which has separate block for each frequency band. Some com paring analysis among the switching method between separate amplifier and multiplier, the structure using frequency selective reflector, and the module using the defected ground structure. The multi function module which operates as amplifier or multiplier with input frequency is developed and input frequency suppression and output harmonics suppression can be improve d by using defected ground structure.