• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2528-2533
• /
• 2007

Thermoforming is one of the most versatile and economical processes available for the manufacturing polymer products. The drawback of thermoforming is difficult to get uniform thickness of final products. For the distribution of thickness strongly depends on the temperature distribution of sheet, the adjustment of heater power is very important In this paper, an optimization study for getting uniform temperature distribution was carried out using dual optimization steps. At first, the steady state optimal distribution of heater power is searched by numerical optimization to get uniform temperature of sheet surface. In the second step, time-dependent optimal heater inputs have been found out to decrease the temperature difference through the direction of thickness using Rseponse Surface Method and D-optimal method. The optimization results show that the time-dependent optimal heater power distribution gives acceptable uniform sheet temperature in the field of forming temperature..

• Journal of Aerospace System Engineering
• /
• v.7 no.3
• /
• pp.1-6
• /
• 2013

Numerical optimization of two dimensional high lift configuration was performed with flow solver and optimization method based on RSM(Response Surface Model). Navier-Stokes solver with Spalart-Allmaras turbulence model was selected for the simulation of highly complex and separated flows on the flap. For the simultaneous optimization of both flap shape and setting (gap/overlap), 10 design variables (eight variables for flap shape variation and two variables for flap setting) were chosen. In order to generate the response surface model, 128 experimental points were selected for 10 design variables. The objective function considering maximum lift coefficient, lift to drag ratio and lift coefficient at specific angle of attack was selected to reduce flow separation on the flap surface. The present method was applied to two dimensional fowler flap in landing configuration. After applying the present method, it was shown that the optimized high lift configuration had less flow separation on the flap surface and lift to drag ratio was suppressed over entire angle of attack range.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.10
• /
• pp.60-67
• /
• 2019

Recently, lightweight materials such as Ti alloys have been used increasingly in the aerospace and high-tech industries for weight loss and fuel efficiency. Because of built-up edges and workpiece deflection due to low stiffness, the Ti alloys have poor machinability. In our study, systematic experiments were conducted to investigate the milling characteristics of the Ti alloy (Ti-6A1-4V) with endmills. The independent variables in the experiment were spindle speed, feed per tooth, and axial depth. Cutting force, acceleration RMS, and surface roughness were measured. Using the response surface method, the optimal cutting conditions were analyzed to improve machining quality and productivity.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.8
• /
• pp.731-735
• /
• 2002

Electro-optical (EO) performances for the twisted-nematic (TN)-liquid crystal display (LCD) photoaligned with linearly polarized UV exposure on the poly［4- (fluorocinnamate) phenylmaleimide](PFCPMI) surfaces using a new photodimerization method were investigated. For a new UVLPH (UV linearly polarized during heating) photodimerization method, the photopolymer layers were exposed by linearly polarized UV dichroic polarizer without a specific UV filter during heating at $150^{\circ}C$. The Voltage-transmittance (V-T) curve without backflow bounce in the photoaligned TN-LCD with UV exposure on the PFCPMI surface for 10 min using the UVLPH photodimerization method was observed. For response time measurement, the transmittance characteristics of the photoaligned TN-LCD using the UVLPH photodimerization method on the photopolymer surface was better than that of the photoaligned TN-LCD using the UVLP photodimerization method under a room temperature.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.1
• /
• pp.59-65
• /
• 2019

In this study, optimal design of direct-drive VCMs (Voice Coil Motor) for a missile fin actuator is carried out. The torque performance and the characteristics of the VCM are predicted by commercial electromagnetic analysis software, ANSYS Maxwell. The optimal design is obtained at the minimum and maximum actuating angles where the aerodynamic load acting on the fin is the largest in the operating range. The critical variables of the actuator is designed and the RSM (Response Surface Method) is used for the optimization. The response surface model consists of second-order functions and its experimental points are selected by a central composite design. This design is widely used for fitting a second-order response surface. The adjustment regression coefficients is computed for adequacy checking of the response surface model. Finally, the torque values obtained by the RSM and the ANSYS Maxwell are shown in good agreement.

• Journal of the Society of Naval Architects of Korea
• /
• v.40 no.6
• /
• pp.1-11
• /
• 2003

For an accurate shock response analysis of a floating structure such as a naval surface ship subjected to an UNDEX(UNDerwater Explosion), the cavitation effects due to reflected wave at free surface and wetted structural surface should be considered. In this study, for the consideration of cavitation effects an effective method using LS-DYNA/USA and its theoretical background were presented. Through the application of the analysis of bulk cavitation phenomena in the free field, it could be confirmed that almost the same results were obtained between LS-DYNA/USA code and the analytical method. for the investigation of cavitation effects from the structural shock response characteristics, three dimensional UNDEX shock response analysis of an idealized ship model was also carried out It could be found that the cavitation Phenomena gave significant effects on the structural shock response characteristics, and especially that the shock loadings calculated at the installed location of shipboard equipment were underestimated in the case of no consideration of the cavitation effects, which might cause the severe mistake in its shock-resistance design.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.42 no.1
• /
• pp.44-53
• /
• 2006

The expansion of near shore aquaculture is feasibility of moving aquaculture facilities into the open ocean. Numerical modeling technique using finite element method was used to enable the optimum design and evaluation of submersible aquaculture cage system. The characteristics of mooring loads response in mooring lines under waves and current and their response amplitude operators were calculated for single and three point mooring configuration at the surface condition and submerged one. The static mooring loads without wave and current loading were similar for both the surface and submerged configuration. It was calculated that three point mooring was more adequate than single point mooring for the mooring configuration of submersible aquaculture cage system. The wave induced response amplitude operators for the single point mooring configuration with the influence of currents were identical to those without the influence of currents.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.1
• /
• pp.26-32
• /
• 2005

In this paper, the effect of various regression models is investigated on structural optimization using the central composite method. Three bar truss and the upper platform of a satellite are optimized using various regression models that are polynomial, exponential and log functions. Response surface method is non-gradient, semi-global, discrete and fast converging in optimization problem. Sampling points are extracted by the design of experiments using the central composite method. Response surface is generated using the various regression functions. Structural analysis for calculating constraints is executed to find static and dynamic responses. From this study, it is verified that the response surface method has advantage in optimum value and computation time in comparison to other optimization methods.

• Computational Structural Engineering
• /
• v.7 no.1
• /
• pp.109-116
• /
• 1994

In this paper, various reliability analysis methods for calculating a probability of failure are investigated for their accuracy and efficiency. Crude Monte Carlo method is used as a basis for the comparison of various numerical results. For the sampling methods, Importance Sampling method and Directional Simulation method are considered for overcoming a drawback of Crude Monte Carlo method. For the approximate methods, conventional Rackwitz-Fiessler method. 3-parameter Chen-Lind method, and Rosenblatt transformation method are compared on the basis of First order reliability method. As a Second-order reliability method, Curvature-Fitting paraboloid method, Point-fitting paraboloid method, and Log-likelihood function method are explored in order to verify the accuracy of the reliability calculation results. These methods mentioned above would have some difficulty unless the limit state equation is expressed explicitly in terms of random design variables. Thus, there is a need to develop some general reliability methods for the case where an implicit limit state equation is given. For this purpose, Response surface method is used where the limit state equation is approximated by regression analysis of the response surface outcomes resulted from the structural analysis. From the application of these various reliability methods to three examples, it is found that Directional Simulation method and Response Surface method are very efficient and recommendable for the general reliability analysis problem cases.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.10a
• /
• pp.341-342
• /
• 2009