• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.1 s.92
• /
• pp.102-112
• /
• 2005

In this work, we developed fully integrated broadband MMIC chip set employing CSP(Chip Size Package) for K/Ka band applications. By utilizing an ACF for the RF-CSP, the fabrication process for the packaged amplifier MMIC could be simplified and made cost effective. $STO(SrTi_{3})$ capacitors were employed to integrate the DC biasing components on the MMIC, and LC parallel circuits were employed for DC feed and ESD protection. A pre-matching technique and RC parallel circuit were used to achieve a broadband matching and good stability fer the amplifier MMIC in K/Ka band. The amplifier CSP MMIC exhibited good RF performance over a wide frequency range in K/Ka band. This work is the first report of a fully integrated CSP amplifier MMIC successfully operating in the K/Ka band.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.3
• /
• pp.51-59
• /
• 2009

This paper presents the design of continuous-time sigma-delta modulator for acoustic sensor. The feedforward structure without summing block is used to reduce power consumption of sigma-delta modulator. A high-linearity active-RC filter is used to improve resolution of sigma-delta modulator. Excess loop delay problem in conventional continuous-time sigma-delta modulators is solved by our proposed architecture. A low power, high resolution fourth-order continuous-time sigma-delta modulator with 1-bit quantization was realized in a 0.13-${\mu}m$ 1-Poly 8-metal CMOS technology, with a core area of $0.58\;mm^2$. Simulation results show that the modulator achieves 91.3-dB SNR over a 25-kHz signal bandwidth with an oversampling ratio of 64, while dissipating $290{\mu}W$ from a 3.3-V supply.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.1
• /
• pp.753-759
• /
• 2020

A modified Chebyshev lowpass filter function with progressively diminishing ripples in the passband is proposed and analyzed in the frequency domain. Owing to the diminishing ripples, the passband magnitude characteristic of the proposed Chebyshev function has improved compared to the classical Chebyshev function. In addition, the phase characteristics of the proposed Chebyshev function were improved considerably compared to that of the Chebyshev function, and the time delay of the proposed function was much simpler and flatter. In addition, the proposed Chebyshev filter was realizable by the passive doubly terminated ladder network delivering maximum power transfer for the order n, even or odd, thus making themselves amenable to low-sensitivity active RC or switched capacitor filters through the simulation techniques. To verify the proposed Chebyshev filter characteristics, a 6th order passive doubly terminated ladder lowpass filter was designed and analyzed using the MATLAB and SPICE program. Thus, the proposed Chebyshev function can remove the drawbacks of the classical Chebyshev function and could be applicable to the design of a filter with an improved filter size, phase, and time delay characteristics for various signal processing.

• Korean Journal of Soil Science and Fertilizer
• /
• v.33 no.1
• /
• pp.15-23
• /
• 2000

RC oscillation method was applied to study the condenser characteristics of two metal sticks insulated by vinyl tube and used in the dielectric constant determinations of most soils. Its capacitance as influenced by the contacted ambient materials was measured as relative capacitance of the sensor sticks compared with the standard one on the RC oscillation circuit. According to the equivalent circuit of the sensor stick set, the measured capacitance was composed of a basic capacitance connected in parallel with sensor stick capacitance, which was composed of lineally connected vinyl tube capacitances and the sensing part capacitance. The dielectric constant (U) of the contacted ambient moist soil located in the sensing part around the sticks interrelated with the other parameters as following equation. $$\frac{1}{C-B}=\frac{k}{U}+Z$$ where C is the output total relative capacitance, B is the hidden and fixed basic relative capacitance, k is a constant related with U, and Z is a constant for the insulating vinyl tube capacitances determined by its thickness and dielectric constant. The constant k is determined by the spacing and length of sensor sticks. The Z value is theoretically an invariable constant, but it may become considerably bigger than the determined in lab if air tube is formed on the surface of sensor sticks by some shocks on them after their installation in soil. Due to the unstability of lab Z value, it may be better to revise it after sensor stick's installation in soil and no shaking shocks should be applied on them.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.2
• /
• pp.80-86
• /
• 2011

This paper presents an integrated variable amplitude high voltage pulse generation circuit with low power and small size for driving industrial piezoelectric printer heads. To solve the problems of large size and power overhead of conventional pulse generators that usually assembled with multiple high-cost discrete ICs on a PCB board, we have designed a new integrated circuit (IC) chip. Since all the functions are integrated on to a single-chip it can achieve low cost and control the high-voltage output pulse with variable amplitudes as well. It can also digitally control the rising and falling times of an output high voltage pulse by using programmable RC time control of the output buffer. The proposed circuit has been designed and simulatedd in a 180[nm] Bipolar-CMOS-DMOS (BCD) technology using HSPICE and Cadence Virtuoso Tools. The proposed single-chip pulse generation circuit is suitable for use in industrial printer heads requiring a variable high voltage driving capability.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.1
• /
• pp.47-55
• /
• 2005

This work describes an 8b 240 MS/s CMOS ADC as one of embedded core cells for high-performance displays requiring low power and small size at high speed. The proposed ADC uses externally connected pins only for analog inputs, digital outputs, and supplies. The ADC employs (1) a two-step pipelined architecture to optimize power and chip size at the target sampling frequency of 240 MHz, (2) advanced bootstrapping techniques to achieve high signal bandwidth in the input SHA, and (3) RC filter-based on-chip I/V references to improve noise performance with a power-off function added for portable applications. The prototype ADC is implemented in a 0.18 um CMOS and simultaneously integrated in a DVD system with dual-mode inputs. The measured DNL and INL are within 0.49 LSB and 0.69 LSB, respectively. The prototype ADC shows the SFDR of 53 dB for a 10 MHz input sinewave at 240 MS/s while maintaining the SNDR exceeding 38 dB and the SFDR exceeding 50 dB for input frequencies up to the Nyquist frequency at 240 MS/s. The ADC consumes, 104 mW at 240 MS/s and the active die area is 1.36 ㎟.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.10
• /
• pp.123-130
• /
• 2016

High-frequency induction heating equipment can heat the metal by applying a High-Frequency power to the resonant circuit. The resonance circuit is composed of the work coil and the conduction-cooled power capacitor, it influences the performance of the heat treatment equipment according to the characteristics of the capacitor. However, dependence on conduction-cooled power capacitor's import is high due to lack of core technology research and development. Minimizing the generation of internal heat transmitted inside during LC resonance, reduce the reactive power loss, there is a need for a capacitor within the voltage characteristic outstanding. To implement localization it is vital that prior study of the analysis on the frequency response characteristic for the finished capacitor advanced manufacturer be implemented. Studying the interpolation method to read the value at any point of the characteristic curve for a given log-log scale was applied to the analysis tool of the capacitor by my proposed algorithm. The simulation for reproducing frequency response curves was attempted by assuming a capacitor in a simplified series equivalent RC circuit to obtain the equivalent series resistance value. It was confirmed that the reproduction rate was the result value above 83% as compared to the simulation of the properties and characteristics on the actual reactive power for Peak value, and that the algorithm can be applicable when analyzing and predicting the characteristic curves of a simpled model capacitor.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.11
• /
• pp.7794-7800
• /
• 2015

Ginsenosides in ginseng berry has been known as functional materials showing physiological effect to the human. Specially, ginseng berry contains plenty of ginsenoside Re, but the study of extraction processes were not enough performed. Accordingly, the purpose of this study was to establish the optimized extraction process for obtaining ginsenoside Re from ginseng berry. The extraction process of ginsenosides was performed in 250 mL extraction flask containing 150 solvent and 10 g of dried ginseng berry. The extracted ginsenoside Re, Rg1 and Rd and total crude ginsenosides from ginseng berry were evaluated by TLC according to the treated conditions (the ratio of alcohol to water, extraction temperature, extraction period, and extraction times). Optimized conditions for extraction was 70% to 30% of the ratio of alcohol to water, $80^{\circ}C$ of extraction temperature, 4 h of extraction period, and 2 times of extraction frequency. The amount of total crude ginsenosides of the extract obtained from the optimized process was 88.6 mg/g based on dried ginseng berry. The composition of ginsenosides from the extracted was 5.5% of Rb1, 5.2% of Rc, 14.3% of Rd, 51.5% of Re, 8.1% of Rf, and 15.7% of Rg1. A protopanaxtriol ginsenosides of whole ginsenosides extracted was about 80%.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.2
• /
• pp.99-105
• /
• 2022

As the chip size gets smaller, the width of the electrode line is also fine, and the density of interconnections is increasing. As a result, RC delay is becoming a problem due to the difference in resistance between the capacitor layer and the electrical conductivity layer. To solve this problem, the development of electrodes with high electrical conductivity and dielectric materials with low dielectric constant is required. In this study, we developed low dielectric ink by mixing commercial PSR which protect PCB's circuits from external factors and PI with excellent thermal property and low-k characteristics. As a result, the ink mixture of PSR and PI 10:3 showed the best results, with a dielectric constant of about 2.6 and 2.37 at 20 GHz and 28 GHz, respectively, and dielectric dissipation was measured at about 0.022 and 0.016. In order to verify the applicability of future applications, various line-width transmission lines produced on Teflon were evaluated, and as a result, the loss of transmission lines using low dielectric ink mixed with PI was 0.12 dB less on average in S21 than when only PSR was used.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.45 no.3
• /
• pp.51-58
• /
• 2008

This paper is a study of a prevention of power folding controller's thermal degradation. Power folding technology has been applied for many fields such as side rear vision mirror of vehicles, windshield wiper, antenna, power window. These controllers have been comprised with traditional DC moors, Switching electronic devices, and relays. But this methods have a limitation to overcome such problems of product reliability, endurance, noise margins. Therefore on this paper, to detect the movement of motor, sensing motor brush noise on a load sensing part has been used and controlling a precise RC timing control minimizes the thermal deterioration of motor. And using MOS FETs as a electronic switching device increases life-time and liability of control circuit. After testing such circuit and control method, repetition of operating time, cut-off time, wide operation voltage, power noise margin ware increased over eleven-fold.