• International Journal of Quality Innovation
• /
• v.5 no.2
• /
• pp.63-69
• /
• 2004

This is an R&D project on design optimization of the inner shield of the Omega color picture tube at Samsung SDI in Korea. This was an R&D project which basically used the IDOV (Identify, Design, Optimize, Validate) process for Six Sigma implementation. Most Six Sgima projects use the process of DMAIC (Define, Measure, Analyze, Improve, Control). However, this project introduces a new cycle, RDIDOV (Recognize, Define, and IDOV). Here CPT means Color Picture Tube. Sam sung SDI is one of the two companies which began Six Sigma in Korea. This case study shows a good example how an R&D Six Sigma project can be usefully employed in manufacturing companies using a new process cycle.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.1367-1369
• /
• 2002

The pitch and stall schemes have some problems such as, mechanical stress, tear and wear on the transmission line, noise emission and disturbance to the grid, due to a delaying factor of mechanical process. In this paper, a novel control is developed. It serves to compensate delaying of pitch or stall schemes and allows the generate power to control in fast response. The validity of the proposed control scheme is verified by experiment results with the actual 660KW wind power system model.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.2 no.3
• /
• pp.185-196
• /
• 2002

MRAM(magnetic random access memory) is a promising candidate for a universal memory with non-volatile, fast operation speed and low power consumption. The simplest architecture of MRAM cell is a combination of MTJ(magnetic tunnel junction) as a data storage part and MOS transistor as a data selection part. This article will review the general development status of MRAM and discuss the issues. The key issues of MRAM technology as a future memory candidate are resistance control and low current operation for small enough device size. Switching issues are controllable with a choice of appropriate shape and fine patterning process. The control of fabrication is rather important to realize an actual memory device for MRAM technology.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.23 no.6
• /
• pp.747-753
• /
• 1986

This paper describes the design and fabrication of a digital volume control integrated circuit which replaces a mechanical volume control. The integrated circuit can be controlled volume by up/down switch. It has been fabricated by SST bipolar standard process. Its chip size is 2.5x2.5 mm\ulcorner As a result, we succeeded in fabrication of integrated circuit which satisfied DC characteristics and proper operation of volume control.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1998.06a
• /
• pp.97-100
• /
• 1998

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.357-360
• /
• 2001

Design Engineering Group, LG Production engineering Research Center has been developing The Integrated Design Environment enabling engineering design task with ease, speedy and accurate for several years targeting the design departments in LG Electronics. $ezDesign^{(R)}$ System is consisted by Engineering Database Management, Engineering Knowledge Management, 3D Design Application, Design Evaluation Method and Project Management. Engineering Database Management manage the design information effectively. Engineering Knowledge Management takes control of design knowledge from design engineering activity systematically. It is possible for the engineering designer to utilized 3D CAD easily by 3D Design Application. Design Evaluation Method can evaluate several design alternatives synthetically. In Project management System, Designer can simulate the project schedule and cost. In this report, We will introduce how design process can be innovated by way of $ezDesign^{(R)}$ System.

• Journal of the Korean Institute of Gas
• /
• v.16 no.1
• /
• pp.22-25
• /
• 2012

Welding and/or fusion in polyethylene(PE) system made on site is focused on the control of the welding or fusion process to follow proper procedure. The process control is important, but it is not sufficient for the long term reliability of a pipe system. To achieve the rate of failure close to zero, Non Destructive Testing(NDT) is necessary in addition to joining process control. For electrofusion joints several non-destructive testing methods are available. The ultrasonic phased array technique is possible to detect various defects including wire deviations and regions with lack of fusion. In this studies, testing was carried to detect the defect after electrofusion joining of polyethylene piping is utilized by the ultrasonic phased array technique. From testing data, ultrasonic phased array technique is recommended as a reliable non-destructive testing method.

• Applied Chemistry for Engineering
• /
• v.31 no.5
• /
• pp.520-525
• /
• 2020

In this study, we developed a machine learning-based model for predicting the production stage temperature of distillation process. It is necessary to predict an accurate temperature for control because the control of the distillation process is done through the production stage temperature. The temperature in distillation process has a nonlinear complex relationship with other variables and time series data, so we used the recurrent neural network algorithms to predict temperature. In the model development process, by adjusting three recurrent neural network based algorithms, and batch size, we selected the most appropriate model for predicting the production stage temperature. LSTM₁₂₈ was selected as the most appropriate model for predicting the production stage temperature. The prediction performance of selected model for the actual temperature is RMSE of 0.0791 and R² of 0.924.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.8
• /
• pp.792-797
• /
• 2009

This paper presents the evaluation of PID and fuzzy control logic for the lateral position control of a moving web in roll-to-roll (R2R) printed electronics. In addition, we report the implementation of computer simulation software that enables us to develop the control logic in a graphic user interface and to test the controller performance in 3D dynamic environment. A mathematical model of the web dynamics is described first to explain the lateral motion of a moving web. Based on the model, PID and fuzzy controllers are designed, and embedded in the simulation software. Under the simulation conditions for fabricating RFID antenna by R2R printing, the results indicate that the fuzzy controller shows a better performance and can be more suitable for R2R multi-layer printed electronics.

• Journal of Aerospace System Engineering
• /
• v.16 no.2
• /
• pp.49-62
• /
• 2022

The purpose of this paper was to present a model analysis-based design process and verification results for the high-lift control system of aircraft. For this, we used Matlab/Simulink, one of the most widely-used physical modeling tools. The high-lift control system can be divided into three domains. (i.e., Electronic control domain, Hydraulic actuation domain, and Mechanical power transmission domain) Based on this division, we modeled each of the major domains and sub-components, and integrated them to complete the complicated system model. During the development process, each model block was tuned by referring to the results of pre-test and parts acceptance tests. As a result, the entire performance model and the developed system were completely verified, through unit components and system integrated performance tests. Finally, we summarize the process and results applied to the design process of high-lift control system and present future work.