• 한국식품영양학회지
• /
• 제32권2호
• /
• pp.148-154
• /
• 2019

The aim of this study was to select compounds for the standardization of fermented Kalopanax pictus Nakai (KP-F), to develop the analysis method using HPLC-PDA and to perform method validation. KP-F is a fermented powder developed to improve the original physiological activities and create a new functionality. Eleutheroside E, Acanthoside B, and Syringaresinol were selected as the standard compounds and developed our own method for simultaneous analysis. The analyte was isolated using C18 column with a gradient elution of 0.05 M phosphoric acid in water and methanol as the mobile phase at a flow rate of 1 mL/min and detected at 210 nm. As a result, all standard compounds showed good linearity with an $R^2$ (coefficient of correlation) of 1.000 and for the limit of detection range of $0.710{\sim}0.831{\mu}g/mL$, and the limit of quantification as $2.150{\sim}2.520{\mu}g/mL$. The precision was RSD (%) of less than 4.80%, while the accuracy was 4.70%>RSD (%) for the range 102.44~110.48%. In conclusion, the developed analysis method is suitable for the detection of Eleutheroside E, Acanthoside B, and Syringaresinol in KP-F.

• 설비공학논문집
• /
• 제25권7호
• /
• pp.406-412
• /
• 2013

A hybrid heat pump is under development with the goal of utilizing 120% of primary energy resources. A plate heat exchanger is added between the compressor and air-cooled condenser of an ordinary heat pump to heat water. For successful operation of the heat pump, it is necessary to develop a control algorithm under various operating conditions. As a virtual test bed for that purpose, a dynamic model has been developed, to simulate its dynamic behavior. It was modeled in transient one-dimensions, with varying phase lengths considered. The model was implemented in Matlab and Simulink. Simulation results were effectively applied to design a control algorithm. They also provided physical insight into how to design and operate the system.

• Journal of Pharmaceutical Investigation
• /
• 제40권5호
• /
• pp.297-304
• /
• 2010

The present work focuses on preparation of olanzapine, orally dispersing tablets by direct compression method. Effect of super disintegrant crospovidone, disintegration time, drug content on in vitro release has been studied. A factorial design was employed in formulating a prompt dispersible tablet. The selected independent variables crospovidone and fmelt showed significant effect on dependent variables i.e. disintegration time and percent drug dissolved. Disintegration time and percent drug dissolved decreased with increase in the level of crospovidone. The similarity factor $f_2$ was found to be 97.48 for the developed formulation indicating the release was similar to that of the marketed formulation. Pharmacokinetics of olanzapine after single-dose oral administration of orally disintegrating tablet in normal volunteers were evaluated and the results showed that PK parameters (Cmax, Tmax, AUC) of the designed ODT matrix were similar to those of commercial product, Zyprexa Zydis$^{(R)}$ as a reference.

• 설비공학논문집
• /
• 제10권3호
• /
• pp.271-281
• /
• 1998

In this study, condensation heat transfer experiments were conducted with two small diameter(ø7.5, ø4.0) tubes. Comparison with existing in-tube condensation heat transfer correlations indicated that the correlations overpredict the present data. For example, Akers correlation overpredicts the data upto 104%. The condensation heat transfer coefficient of the ø4.0 I.D. tube was smaller than that of the ø7.5 I.D tube; at the mass velocity of 300kg/$m^2$s, the difference was 12%. The pressure drop data of the small diameter tubes ware highly(two to six times) overpredicted by the Lockhart-Martinelli correlation. Subcooled forced convection heat transfer test confirmed that Gnielinski's single phase heat transfer correlation predicted the data reasonably well.

• Bulletin of the Korean Chemical Society
• /
• 제17권1호
• /
• pp.24-28
• /
• 1996

A procedure is described for the synthesis of the title compound via phosphotriester intermediates. The preparation of $R_p$ and $S_p$ diastereomeric dinucleotide of d[Cp(S)T] was performed by the condensation of the protected deoxycytidine, the protected thymidine, 2,5-dichlorophenylphosphorodichloridothioate and 1-hydroxybenzotriazole in THF. Their designation of configuration at phosphorus as $R_p$ and $S_p$ follows from anaylsis of ${31}^P$ NMR spectroscopy and reverse-phase HPLC and the stereospecificity in the hydrolysis catalyzed by Nuclease S1 and snake venom phosphodiesterase. Diastereomerically pure $R_p$ and $S_p$ d[Cp(S)T] were utilized to synthesize oligonucleotides containing the XhoI recognition sequence with a phosphorothioate group at the cleavage site.

• 약학회지
• /
• 제54권4호
• /
• pp.295-299
• /
• 2010

The aim of this study was to develop and validate for determination of alibendol in human plasma by HPLC method. After precipitation of 500 ${\mu}l$ plasma samples by 50% methanol 50 ${\mu}l$ and 60% perchloric acid 30 ${\mu}l$ and the supernatant 50 ${\mu}l$ was injected into HPLC. The assay was performed isocratically using 10 mM potassium phosphate (pH 3.0) and acetonitrile (80 : 20, v/v) as mobile phase. The $C_{18}$ column (particle size $3.5{\mu}m$, $4.6{\times}50$ mm, Zorbax Eclipse) was used as a solid phase. The mobile phase was delivered at a flow-rate of 1.7 ml/min, detection was by ultraviolet absorption at 232 nm and concentrations were calculated on the basis of peak areas. In these conditions, alibendol can be separated from ethylparaben, the internal standard, and endogenous substances. The retention times of alibendol and ethylparaben were just about 2.6 and 3.5 minutes, respectively. This rapid HPLC method was validated by examining the precision and accuracy for inter- and intra-day analysis. The standard curve was linear ($R^2$=1.0000) over the concentration range of 0.05~20 ${\mu}g$/ml. The inter-day relative standard deviation (R.S.D.) and accuracy were 0.2~12.2% and 94.4~101.2% (82.7% at the lower limit of quatitation). The intra-day R.S.D. and accuracy were 0.1~11.8% and 98.8~102.5%, respectively. The method was successfully applied to the determination of alibendol in plasma for a pharmacokinetic study.

• 센서학회지
• /
• 제23권2호
• /
• pp.105-109
• /
• 2014

Structure and electrical properties of $0.85NaNbO_3-0.15LiNbO_3$ ($(Li_{0.15}Na_{0.85})NbO_3$) ceramics were investigated as a function of sintering temperature. $(Li_{0.15}Na_{0.85})NbO_3$ ceramics were prepared by conventional solid state processing. A main phase of the orthorhombic perovskite structure and secondary phase of $LiNbO_3$ were confirmed for all sintered specimens. Dense $(Li_{0.15}Na_{0.85})NbO_3$ ceramics were obtained at sintering temperature above $1050^{\circ}C$. With increasing sintering temperature, the electromechanical coupling factor ($k_p$), piezoelectric constant ($d_{33}$) and relative dielectric constant (${\varepsilon}_r$) of the sintered specimens increased, while the mechanical quality factor ($Q_m$) decreased. These results are due to the increase of grain size and crystallite size of orthorhombic perovskite structure. Based on the temperature dependence of ${\varepsilon}_r$, stable piezoelectric properties were expected because no phase transition found up to $300^{\circ}C$. Typically, kp of 18%, $d_{33}$ of 34.7 pC/N, ${\varepsilon}_r$ of 135, and $Q_m$ of 62.8 were obtained for the specimens sintered at $1200^{\circ}C$ for 5 h.

• 국제학술발표논문집
• /
• The 9th International Conference on Construction Engineering and Project Management
• /
• pp.1179-1186
• /
• 2022

Building Information Modeling (BIM) is widely used to efficiently share, utilize and manage information generated in every phase of a construction project. Recently, mixed reality (MR) technologies have been introduced to more effectively utilize BIM elements. This study deals with the haptic interactions between humans and BIM elements in MR to improve BIM usability. As the first step in interacting with virtual objects in mixed reality, we challenged moving a virtual object to the desired location using finger-pointing. This paper presents the procedure of developing a haptic interface system where users can interact with a BIM object to move it to the desired location in MR. The interface system consists of an MR-based head-mounted display (HMD) and a mobile application developed using Unity 3D. This study defined two segments to compute the scale factor and rotation angle of the virtual object to be moved. As a result of testing a cuboid, the user can successfully move it to the desired location. The developed MR-based haptic interface can be used for aligning BIM elements overlaid in the real world at the construction site.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2001년도 춘계연구발표회 논문개요집
• /
• pp.68-69
• /
• 2001

• 한국지진공학회논문집
• /
• 제24권4호
• /
• pp.169-178
• /
• 2020

In a previous paper, ambient vibration tests were conducted on a cable stayed bridge with resilient-friction base isolation systems (R-FBI) to extract the dynamic characteristics of the bridge and compare the results with a seismic analysis model. In this paper, a nonlinear seismic analysis model was established for analysis of the bridge to compare the difference in seismic responses between nonlinear time history analysis and multi-mode spectral analysis methods in the seismic design phase of cable supported bridges. Through these studies, it was confirmed that the seismic design procedures of the "Korean Highway Bridge Design Code (Limit State Design) for Cable Supported Bridges" is not suitable for cable supported bridges installed with R-FBI. Therefore, to reflect the actual dynamic characteristics of the R-FBI installed on cable-supported bridges, an improved seismic design procedure is proposed that applies the seismic analysis method differently depending on the seismic isolation effect of the R-FBI for each seismic performance level.